MikroTik

joserudi

Hello, is there any way to delete the logs that are in payments? Thank you

joserudi

Hello, is there any way to delete the logs that are in payments? Thank you

joserudi

After upgrading to 6.45.1 PPPOE Profile bandwidth defaults are not creating simple queues. Radius auth is working but if the radius server does not send Mikrotik-Rate for a user ( meaning use the profiles default settings ) it does not. Only users with a defined Mikrotik-Rate get simple queues crea...

joserudi

Hi, is mikrotik planning to use arm devices in sector antennas like mantboxes now that nv2 works correctly? Thank you

joserudi

Now that works perfectly nv2. Will it release mikrotik mantbox with arm that admits a greater number of users and throughput?

joserudi

40 MHz 1 tcp between two arm devices.

joserudi

Nv2 in PTP with arm works now fine:

802.11 90 Mbps
Nstream 105 Mbps
Nv2 156 Mbps

joserudi

Could a mantbox with an arm routerboard give more speed and number of users than with mipsbe routerboard?

joserudi

I can not believe it, the nv2 works perfectly in arm with version 6.44rc4 giving more speed and stability than nstreme or 802.11.

joserudi

I have tried a mikrotik base station and to give an acceptable speed I can not associate more than 20 clients. I have tried a cambium base station updating the mikrotik client to the ptp elevate cambium firmware and get the same speed but with 60 clients per base station. Is the speed restriction ha...

joserudi

I have the same problem. +1

joserudi

I hope you have not considered it resolved because it still does not work. It's a pity being such a good product that it does not work. Finally we will have to return several units.

joserudi

*) wireless - improved Nv2 reliability on ARM devices; The first point-to-point tests with nv2 on arm are not satisfactory. We will perform more tests Just a question without intention of doubting what you say: why use NV2 on PtP? I always use nv2 with mikrotik. There are some noise in my city.

joserudi

Hi, in my case with a good signal on arm when going from 802.11 or nstreme to nv2 the level of ccq falls and the link appears at 6mbps. It goes back up to 90% and then falls again continuously when passing traffic. In 802.11 or nstreme it is stable.

joserudi

Version 6.43rc45 has been released.

*) wireless - improved Nv2 reliability on ARM devices;

The first point-to-point tests with nv2 on arm are not satisfactory. We will perform more tests

joserudi

*) wireless - improved Nv2 reliability on ARM devices;

The first point-to-point tests with nv2 on arm are not satisfactory. We will perform more tests

joserudi

New 6.43rc44 (Release candidate) but nothing to do.

joserudi

*) userman - fixed compatibility with PayPal TLS 1.2;

Paypal works perfectly now. Many thanks.

joserudi

I join the request, we use paypal daily and it is causing us a lot of inconvenience. Thank you

joserudi

Thanks, I see that there are several Twisport adapters but I do not see any specific for netmetal or netbox. Which you use to adapt the mikrotik euqipos to the horn antennas rf elements

joserudi

What a great news, I see some symmetrical novelty that I do not understand very well. What do you recommend the 30º, 60º, 70º, 80 or 90º. Have you tried any?

joserudi

I need to locate several antennas at the same point with a high density of clients. Have you tried the new 5 GHz, 3x30 ° HD Sector Antenna from Ubiquiti with netmetal equipment? I think it could turn out very well.

joserudi

*) wireless - improved Nv2 reliability on ARM devices;

I'm sorry to indicate that the nv2 protocol on arm devices continues to fail. It is unstable and has packet loss. Nstreme is still the best option

joserudi

*) wireless - improved Nv2 reliability on ARM devices;

There are no improvements in this regard, the nv2 protocol in arm devices remains unstable. It continues to have packet losses. At the moment nstreme is the best option.

joserudi

With nv2 and the new update we get 96 mbps per sector with 15 users and good signal. Great news

Now we need to improve in nv2 ptp since we can not get past those 100 mbps in ptp mode as well.

joserudi

I have started testing this version. So far the issue of one client having high download causing slowness to other clients has been resolved. Mikrotik great and good work on this. We are going somewhere now One question is dynamic downlink ratio behaviour changed? In 6.42.2 with ratio of 60% ap can...

joserudi

Good morning, I wanted to know if there are improvements regarding version 6.42 where the same was announced or there are improvements in this regard:

Release 6.42

*) wireless - improved Nv2 PtMP performance;

joserudi

So they do not think about solving it? There are scenarios where only works correctly using nv2

joserudi

Best regards, I love the idea of having ac devices with architecture arm with greater processor and memory. The problem is that I have tried to do point to point with all the new versions both current and release and I can not get it to work correctly in nv2. In nv2 the ccq is unstable and there is ...

joserudi

All its ok in tile.

joserudi

Hi friends, could you tell me if the tests were done with dynamic or fixed downlink / uplink ratio. Thank you

joserudi

Fixed the correct ip but continues to stop users with time until you make a database rebuild

ppp - send correct IP address in RADIUS "accounting-stop" messages (introduced in 6.39);

joserudi

good afternoon, there has been a problem that I would like to comment. I have a pptp bridge. The station is linked in turn to a netmetal5 all in bridge. I happen to have several customers with antennas SXT 5 with version 5.26 and have now added several SX5 lite with 6.30.4. When the pptp cut or freq...

joserudi

Don´t work, I need to clear the counter of sessions and just let me clear in 1000 and 1000 there are 30,000 records

joserudi

I only need clean count session. I have registered two years. I would like to use tool/user-man/session clean but I only can clean one number. Numbers 0-20000 dont work.

joserudi

Please tell me how you clean session logs because I only can remove 1 on 1 withs this option tool/user-manager/session/remove numbers. Thanks

joserudi

Yes. The router its radius ser server too. My data base its more than 100 Megabytes. I need to clean sesión user database.

joserudi

Hi, I am testing the new version 6.33 RC16 to try to clean the historic session but I can not properly use the userman / history / clean command. 1000 users currently handle with radius on the same machine as the PPPoE server and each time it restarts take long to respond database. How we can stream...

joserudi

ROS 6.28rc18 and User Manager 6.28rc18 Works fine. Thanks MikroTik.

http://www.mikrotik.com/download/share/ ... latest.zip

joserudi

ROS 6.28rc17 and User Manager 6.28rc17 still the same error.

joserudi

Any solution?

joserudi

Hi Friends, since last March 24 paypal not return correctly: PayPal - ssl connection error: handshake failed: unable to get local issuer certificate (6)

Can you test your returns? Thanks.

joserudi

"operation failed" and no disconnects me users on the remote server. If you try the two servers in lan doing well but passing through an area not wan's me off. Open ports and remove all filters but something escapes me to work correctly COA ports or something. Thank You

joserudi

Thanks for answering. Only I try to close active session by selecting the user and clicking edit / logout in active sessions with local users no problem but with the remote routers me indicates failure in the operation

joserudi

Hello friends. I have remote routers configured correctly and properly authenticated clients from each location. The problem I have when a user expires or when I try to close sessions dont disconnect from remote routers. Any ideas? Thanks

joserudi

Good friends, needed to implement a hotspot (with pppoe everything goes perfect) on an interface in bridge mode and works fine until I try to close a user session manager and always gives me 503 error and not close sessions or eject users who are expiring. Use CCR1036 with 6.18. If I implement the p...

joserudi

Good friends, needed to implement a hotspot (with pppoe everything goes perfect) on an interface in bridge mode and works fine until I try to close a user session manager and always gives me 503 error and not close sessions or eject users who are expiring. Use CCR1036 with 6.18. If I implement the p...

joserudi

With 6.19 paypal not works, Another friend say that until 6.18 it works fine.

joserudi

PayPal dont work in this versión. After upgrade from 6.13 show this error:
"PayPal - ssl connection error: handshake failed [unable to get certificate CRL] (6)"

joserudi

Its possible to open a ticket to advertirse this problems to resolver as soon as possible.?

Search found 66 matches