MikroTik

OrCAD

Hi @mrz
in bgp_in I set 0.0.0.0/0 ?
Filter mechanism in ros7 is very strange.
I don’t see any complete example

Thank you

OrCAD

Hello, I try bgp session without success. plese let me konw how to setup: i want to connect AS12345 to IP: 11.22.33.44, my AS 11111 and one /22 to announce, in example 10.0.0.0/22 I've setup a template then connection in ebpg-peer: /routing bgp template add as=11111 name=NR output.filter-chain=myAsF...

OrCAD

LACP support?

OrCAD

Pls explain all with a few example script..

Regards

OrCAD

Hello,
link to download all? torrent?

thank you

OrCAD

WiBox Slant + RB912

I Use Slant before ONE year... UBNT invet Warm Water

See you

OrCAD

Hi,
is possible get your slide about pppoe over vpls ?
thanks..

OrCAD

I've bug with eoip interface disappear with some pppoe registrations. Is impossible to add new eoip tunnel with pppoe server on it.

When release 6.13 ?
or where I can download RC?

thans in advance.
IM

OrCAD

Can RouterBoard do a serial-to-serial over IP ?

serial <-> RB450 <-> IP Tunnel <-> RB450 <-> serial

OrCAD

You use a simple queue or a PCQ queue?

OrCAD

question: with same hardware, you think 900 pppoe cusotmers with PCQ is better then 900 with simple queue ?

with rc12 MikroTik guru say simple queue burst 9x faster, but I think PCQ is winner when same speed is shared in more than 1000 customers.

it's true?

Thanks

OrCAD

pls provide to metal case...

thanks

OrCAD

LCD RC7
Solved with reset configuration then restore previous backup....

thanks and I hope to see a new Ros Stable RC8

OrCAD

last build, LCD still not work... and frequently reboot

OrCAD

LCD not connected after RC7 upgrade...
any news?

thanks

OrCAD

Solved,

the problem in the old RouterBoot was the memory frequency setting = 250MHz
I set this a 225Mhz then now all is perfect.

Thanks.

OrCAD

Hi,
my 2011L is locked to bios 2.41 and start only if I press reset switch.
I try with netinstall, with 5.22 and 6.0rc5, I copy 3.02 firmware file then upgrade and reboot but bios is always 2.41 and RB don't start !!
Any idea to upgrade and return in normal reboot conditions?

Thanks in advance!

OrCAD

They flashing before Mikrotik boot... I think is possible to correct.

OrCAD

pls make the test in TCP mode.

OrCAD

Sure,
but I prefere to use one only cable, with routing... then 435G

thanks

OrCAD

...and RB433UAH with 2x R52nH ?
...I think the optimus is 435G with two card a both side because 433AH have a 100mbit port..

thanks.

OrCAD

48h and don't stop (with ether13 disabled)

OrCAD

I've disabled ether13, now is 24h not stop...

I hope MikroTik engineer can be made stable this router.

Thanks..

OrCAD

many Kernel Failure every days... with ROS 5.17 and all interface Queue in only-hardware-queue

rapid solution is welcome.

Thanks in advance..

OrCAD

MikroTik use capacitor with low peak voltage. Is crazy to use 6,3v in line of 5v. I've benn replaced all the capacitors in my RB in high tower with 560uF 10v (doubled than 5v) and all works ok from 12v to 48v of power supply. My RB damaged is: RB800, RB450, RB433AH and many RB411AH supplyed at 24v o...

OrCAD

add a 90° Nmale to N female right adapter..

OrCAD

I confirm... Design skin still available!!

OrCAD

Let's go to modding...

Nand chip is 512Mbit x8 bit 2,7 to 3,6volts: NAND512W3
I try to change with 1Gbit x8: NAND01GW3

MikroTik pls stay tuned

OrCAD

Hi,
my latest topic is locked from MikroTik, is 1100AHx2 a fault project?
I propose to all 1100AHx2 users to:

1- return back the device for Nand memory upgrade
2- return back the device for money refuse

It's crazy to have a very wonderfull device with this limitation...

Best regards..

OrCAD

your routeros upgrade files is at limit of free RB1100AH space !!!
and when out ROS6 ?

thanks

OrCAD

Yes I know perfecly what is RAM...
but I think a little NAND is a limitation... I remember RB532 with 128MB Nand and I'm not understand the 48Mb free in RB1100ahx2
I refuse this engineer idea...it's only my things..
Thanks for all, great job.... but increase nand storage!

OrCAD

Hello guys,
what is the winner in LAN tcp troughput?
and in multi wireless readio backbone?

thanks..

OrCAD

normally is 15Mbye used, if you have a few backup.... ros 5.12 cause a 0% free memory....
my question is: why only 47Mbyte HDD on this beautifull router ?

thanks

OrCAD

flash... not RAM

OrCAD

Hi,
one question about RB1100AH and RB1100AHx2 for the mikrotik project engineer...

WHY 47MByte in this router? HOW many different cost with 64MB ? RB450 have 512MB !!

is problematic to upgrade to 5.12

this is crazy!!

Best Regards

OrCAD

Ok, thanks..
I see the fan up when cpu 100% or heatsink is over 40°C
good job.

thanks

OrCAD

fan don't start, in manual mode (main or auxiliary).... in auto and CPU Temp 41°C don't start... what is the minum temp to start in auto mode?

thanks

OrCAD

Hi,
I received 1100AHx2 and fan system not work in manual and auto.
I check it with Ros5.11

thanks

OrCAD

yes, I think to mod the query.... let you know...

OrCAD

exactly, I'm work to rlm_sqlcounter... then post my results...

Thanks..

OrCAD

Hello, I've this scenario: client pppoe TPLINK <---> mikrotik CPE antenna <---> AP mikrotik <---> PPPoE Server inside CPE I've bridge1 = wlan1 + ether1, if I try to start pppoe in tplink this not connect, if I start pppoe inside mikrotik CPE with interface=bridge1 it works... where is the problem fo...

OrCAD

yes, when the client reached the total data is disconnected, but if I try to relogin, I been accepted from hotspot...
I think is necessary to define sqlcounter....only with mikrotik attribute is not possible!!

correct?

OrCAD

in hotspot tab: Limit Uptime and Limit byte Total work fine, but I need this with Freeradius & MySql

thanks..

OrCAD

thanks,
but can I made this profile?

profile1: all of the client in this profile have total traffic 100MByte for 30 days, next client expired
profile2: all of the client in this profile have total connection time 1h / 30 days with data unlimited, next client expired

thanks anymore

OrCAD

I am using OS 5.0 with freeradius & MySql with DialupAdmin interface and I want to create two user profile, the first with time limit and second with total data limit.
I can use a dictionary words?
I see rlm_sqlcounter script, anybody can help me?

thanks in advance
I.M.

OrCAD

Hi,
yes I've Novatel EU850D and RB800 with 5.0rc7 not see this hardware...

news about?
thanks mikrotik

OrCAD

OrCAD

retina display supported?

OrCAD

Hi,
how to add FreeRadius monitor with dude?
I've add the dude IP in the radius client.conf file but the default dude check string cause a abnormal packet string in radiusd -X debug.

Anybody can help me?
thanks in advance...

OrCAD

OrCAD

Hi at all,
When ROS can support bluetooth device and Advertisement function?
Bluez package on debian to compile in ROS!!!

Thank you...

OrCAD

Is possible pass "PPPoE Local Address" with FreeRadius attribute?

OrCAD

Thank Sergejs but this don't work. I've: PPPoE Server with FreeRadius reply & SQL database. I've created a dummy account in the database, this account return a MikroTik Framed-IP=192.168.1.2 and Framed-Route=192.168.1.0 192.168.1.1 1 In the PPPoE Server default profile I NOT set the Local addres...

OrCAD

Hi, one question about freeradius & mikrotik attributes: I need to pass in autentication section different IP, Netmask & gateway to my client without use "service name". now, for IP -> framed-IP-address for netmask -> framed-netmask for gateway? Framed Route? But in the manual I do...

OrCAD

ok,
with port 20,21 and after reboot ftp passive mode work...
many thanks at all...

OrCAD

yes is enable,
and I 've try to add port 20 in firewal service-port and hotspot service-port,
pls check if is a bug or not...

Best regards

OrCAD

I setup my Hotspot in Vlan interface and ftp (passive mode) not work!
my RB is with ROS 2.9.27, update is necessary to solve this problem?

many thanks in advance..

OrCAD

RB532+RB564+2xCM9

Window Frequency select don't work!
I see only 2437Mhz... or manually rewrite this.

dude package?

OrCAD

Hi Devrim,
can U explain in detail this configuration?
many thanks..

OrCAD

Hey GURU, I want to modify my checkrad file to work with more than 20 RB in the HyperLan backbone and test if snmp is better or telnet.. steps: - enable simulcheck in sql.conf - add attribute :=1 in rad sql table - snmp=on in radiusd.conf - radutmp and SQL enable in autorization section - enable snm...

OrCAD

how to modify checkrad file step by step?
another question: how to delete duplicate account in the "online users" table? I see user connected up to 5day but this user not is online...
Ragards..

OrCAD

Welcome back Savage, where to find this documentation? (/usr/share/freeradius/doc ??) I try to enable the query_check in the sql.conf and inside table Simultaneous-Use:=2 with Dialupadmin webpanel but I've problem with PPP users.. Tomorrow I try to insert "return= 1" in the checkrad perl s...

OrCAD

Hi,
if I want to use "Simultaneous Use:=1" Dialup Admin option is necessary RB incoming telnet permission?
Exist one alternative metod to verify if any user is already connected from another my network RB (NAS)?
I see SNMP or Telnet finger type... it's a good way?
Regards in advance..

OrCAD

Hi,
how to use "Simultaneous Use" option to check multiple connection?
I've more than twenty RB and I want to check if any user try to log to a diverse RB..
Thanks in advance..

OrCAD

Ok savage...
solved.... Local Address in default PPP profile...
now work all ok.... coming step two: rp-pppoe server...

thank for judgement

OrCAD

No savage, Autentication with Mikrotik PPPoE and secret in pppoe-user work fine. I want to autenticate my pppoe users with Mikrotik PPPoE server and FreeRadius with DialupAdmin inteface. radiusd.conf and dialupadmin (mySQL db) work wery well with Mikrotik Hotspot interface but when try to add PPP in...

OrCAD

thank for the reply,
Framed-IP-Addess work correctly, otherwise Pool work fine
Framed-IP-Netmask return the correct data, I've check Framed-Route without success...

I use sql database not users file, where to find 'DEFAULT PPP Profile' ?
regards..

OrCAD

Hi, my freeradius work fine with HotSpot but when I check ppp I've one error. Log is paste below... _______________________________________________________ 14:16:43 pppoe,info PPPoE connection established from 00:15:D6:02:03:54 14:16:43 pppoe,ppp,info <pppoe-0>: waiting for call... 14:16:46 radius,d...

OrCAD

I think is wonderful redirect signal strenght to RS232 then attach a simple circuit with IC3915 10 or more led driver.

OrCAD

OrCAD

Yes,
WRT54G work fine with mikrotik hotspot and Atheros / Prism 2.5 card.
I use this in WDS or Client NatRouter (Talisman) with PPPoE or normally
and not have a problem. Is perfecly compatible..

OrCAD.

OrCAD

Is simple,
add future to unlock CF then mesh with internal memory...
or add SO-DIMM connector for memory expansion, same in the RB230.....

OrCAD

OrCAD

OrCAD

OrCAD

Now, the RB532 easy mod to activate minipci green LED!!
PLZ routerboard.com engineer, connect all GND track!!! .... and add 128MB RAM 10x

OrCAD

OrCAD

10x Montana, I've immaginate it...
Tomorrow I try with pure bridge..
Regards

OrCAD

Hi,
I've little question about SR5 and 2.9rc10 OS.
In my link, 18Km with two SR5 and two 24dB parabolic dish, when I set operational frequency, in ex. 5500 in the first RB (AP) and 5600 at the second (station), I obtain "connected to ess", why?
regards

OrCAD

I solve this problem simple changing frequency at both RB then apply... "connect to ess" finally appear.... New problem is speed too slow at 5G with SR5. 2.9rc6 in both side work great, I upgrade with rc10 and Bandwidth Test return TCP & UDP send very slow bandwidth (43kbps). Receive m...

OrCAD

I've RB with 2.9rc10 with BIG problem in bandwidth caused, I think, from firmware.. rc6 work fine. Now, I cannot downgrade to rc6 because Netinstall not install rc6. I've delete all package then I loaded Netinstall without success... only rc8 to rc10 is been istalled. error in serial console: omitte...

OrCAD

This is a good idea.... install a power supply plug and disable
internal regulator only for high power miniPCI installed.
RB502 without able to use up to 4 SRx is crazy or bad solution..
Regards

OrCAD

Hi,
I've same problem and I try to explain in wireless section post.
I think is a bad SR5 management of the latest wireless package
CM9 work without problem.
regards

OrCAD

Why I've to enable WDS?
I think this is a negotiation error or bad management of SR5!
WDS or not, ap-bridge and station in other side now don't work
idem for bridge mode in both side.
My SSID's and frequency match but return only "assoc timeout"
Tomorrow switch to CM9.
Regards

OrCAD

Hi, I've made the same way! First, ap-bridge and station work perfectly Next, I've try to align the two parabolic dish with RB Alingment-only utility, after this I put one RB in ap-bridge and the second in station mode. At this time I received assoc timeout error, but if I scan from station I can se...

OrCAD

Hi,
I've this result in log:

wireless,info wlan1: failed to connect to 00:01:B4:02:0B:1E, assoc timeout

the link is: 2 RB532 with 2 SR5 whit same parabolic dish at -79dBm a 14Km configured AP bridge - station
where is the problem?
many thanks.

OrCAD

oki,
for link align I can use one RB in "alignment only" and in other RB (slave) I check align button?
I think not have perfect direction or I receive with a secondary lobe in one of the two parabolic antenna.
Is possible?
Regards

OrCAD

At the both end I've -78dBm -80dBm, same antenna (grid parabolic antenna Stella Doradus) and same miniPCI ubiquiti SR5.
I've best tranfer rate in only one direction..
regards

OrCAD

Yes, understand all
but RouterOS<-->RouterOS in configuration AP<--->station
a 5Ghz with SR5
Bandwidht test return positive result only in send mode from AP RB
or equivalent receive mode in station RB.
WDS can resolve?
regards

OrCAD

oki, thanks
but why I've result in only one direction?
PC <---> RB
PC receive and RB send (12mbit)
then
PC send and RB receive (zero)

I can test link only with PC in each side then run Win Bandwidht test?
Another 10x.

OrCAD

Hi,
yes, system CPU still to 100% in receive mode and send mode, but in send mode (UDP) I have 7-12mbit and in receive mode (UDP) I have too small bandwidht!!
How to run bandwidht test throught the router?
Is possible? Receive only 48-80 kbit?

many thanks

OrCAD

Hi,
yes, system CPU still to 100% in receive mode and send mode, but in send mode (UDP) I have 7-12mbit and in receive mode (UDP) I have too small bandwidht!!
Is possible? Receive only 48-80 kbit?

many thanks

OrCAD

Hi, I've two RB with SR5 at 13,5Km. Link is stable a -79dBm 24Mbit. When I running bandwidht server in RB1 and bandwidht test in RB2 I see this: Direction=receive receive average 10s= 12Mbit Direction=send send average 10s= 34kbit When I running bandwidht server in RB2 and bandwidht test in RB1 I se...

OrCAD

Idem situation for the SR5... I've lock datarates at 6Mbit,9Mbit,12Mbit because jitter over 18 cause disconnection and continuos negotiation exchange..
I think CM9 is already the best..

Regards

OrCAD

Hi,
thank's to reply...

10.10.0.1 is my server gateway ... 10.10.0.1 <-> 84.xx.xx.xx internet
10.10.0.0/24 is the network from server to RB1
RB1 have ip:10.10.0.30/24
I try to nat: 10.0.4.2 to 10.10.0.40 in the range of the server.... fail!

another crazy idea?

10x

OrCAD

Hi, I have two RB 532 with L5 OS and I have a problem with this configuration: adsl (10.10.0.1) <--> ether2(RB1: 10.10.0.30) ...........................| ...........................-> wlan2 (RB1: 10.0.4.1) with SR5 station mode ...........................| ...........................-> wlan1 (RB1: 1...

OrCAD

Plz post list in OS2.9 syntax !
10x

OrCAD

Ares and bShare (gnutella) is not possible to limit! Block only.

OrCAD

No problem, but is very simple to copy & paste from terminal...
only from OS 2.9 because 2.8 input line is different..

another thanks

OrCAD

Plz post virus-rules list for 2.9 terminal input ?
10x

OrCAD

I would try to change LD regulator...
soon my result in this tread..
Regards

OrCAD

Apply rule then reboot...

OrCAD

U cannot drop "connection estabilisched", try to reboot RB at 01:00 and 06:00 this work fine.
Otherwise, set TCP Estabilisced Timeout= 00:01:00. After 1 min & with firewall P2P lock, estabilisched connection automatically dropped.
Regards

OrCAD

I've same problem, in log I see "lost dhcp lease" caused, I think, from B in Active User... can I solve this?
10x

OrCAD

Solved...
I've switch chain from FORWARD to PREROUTING

Best regard's.

OrCAD

Many thank's, but I've another question: ---- mangle ----- 0 chain=forward p2p=all-p2p action=mark-connection new-connection-mark=p2p_conn 1 chain=forward connection-mark=p2p_conn action=mark-packet new-packet-mark=p2p 2 chain=forward connection-mark=!p2p_conn action=mark-packet new-packet-mark=othe...

OrCAD

and after scheduler successfully enable rule for P2P lock, hotspot user's still to conitinue p2p-download.
How to block this?
I want to kill all estabilisced connection with p2p IP because filter rule:

chain=forward p2p=all-p2p action=drop

not work!
Is possible?
10x

OrCAD

/system script 0 name="p2p_disable" owner="admin" policy=ftp,reboot,read,write,policy,test,winbox,password last-started=may/08/2005 12:53:44 run-count=4 source=/ip firewall filter {disable [find comment="Lock P2P"]} 1 name="p2p_enable" owner="admin" ...

OrCAD

Hi, I want to perm-drop gnutella (shareaza) P2P protocol this rule's are sufficient? chain=forward in-interface=ether2 out-interface=ether2 protocol=tcp tcp-flags=syn,ack p2p=gnutella connection-state=new action=drop chain=forward in-interface=ether2 out-interface=ether2 protocol=tcp tcp-flags=syn,a...

OrCAD

Hi, I have this bug, somewhere p2p-enable or p2p-disable scheduler fail or don't execute command. script /ip firewall filter {enable [find comment="lock P2P"]} scheduler setting is: start date= (today) start time=22:00:00 step=24:00:00 (1day) I use regular NTP-client for read time & da...

OrCAD

Hi,
I can control with Dude four RB532 from external IP (in remote) and add & remove user?
Is possible to create the virtual map of my network with custom alert popup's?
Regard's.

OrCAD

oki, work...
but, if my PC don't have DHCP setting and have a private IP set in the range of RB DHCP Server, already connection establisced.
I would to disable this...

Regard's
OrCAD

OrCAD

Hi,
how to setting up hotspot interface for accept dhcp user's only?
Any other with fixed IP or private can't access.

Regard's

OrCAD

Where?

10x.

OrCAD

configuration race begin!

OrCAD

Nice,
option 4 in boot menù (f) is 399Mhz, next power shutdown and..... work fine!

CPU load % decrease but I think to add a fan for the continuosly operation mode.

Regards

OrCAD

I have same board... how to increase clock speed? 266 -> 333?
10x

OrCAD

oki, for complete tracking log I have add this rule: forward in-interface=wlan1 out-interface=ether2 packet-size=50-1500 action=log is necessary limit min packet-size because log is too heavy! Now, I want to unsend same packet (x user) in log for limit occupation band... i.e. send only new packet or...

OrCAD

Unchecked Default forwarding in wireless interface....in my RB not work..
Second way is to create firewall rule:
forwarding - src-adr=(gateway ip) - dst-adr=(gateway ip) - action=drop

with this rule you can block user p2p traffic.
bye.

OrCAD

oki, this solution work perfecly, many thanks.....but default forwarding not work properly.... solved in 2.9rc5?
OrCAD

OrCAD

I have default forwarding ON in wireless interface.
Each user in connect list have default forwarding OFF (unchecked)..

user's can share!
I don't understand the procedure?

OrCAD

I unchecker DEFAULT FORWARDING in wireless wLan1 but client still to communicate with each other... Why?
Is 2.9rc4 bug?

10x

OrCAD

OS2.9rc4
I have unchecked "default Forwarding" in wireless interface menù but registered client still to comunicate with each other!!
Is a bug?

thanks

OrCAD

Ok, I try this and post result....
Many thank's....

OrCAD

OrCAD

Oki, I understand all.....but one question: if a malicious user, in my network, damage one url or other, after (x es.:)1month where find: - user name - source ip - destination ip damaged - time - mac of user ecc ? Nomadix save log each day in this format! (Nat 1:1 or not) Is a stupid question? 10x t...

OrCAD

Hardware configuration: hotspot users <---> RB532 <--> Internet gateway I want to track (log file) destination ip for each user with source ip association: ip hp-user <---> ip request in gateway or ip hs-user ---> ip request in gateway I have nomadix AG2000w+ in another network and log is composed e...

OrCAD

any idea?

OrCAD

Hey boy I have tree insolved question: - many RB with os 2.9rc4 I can add to Dude? - Dude can report (log, complet ip track vs internet) like nomadix (ip source:port <-> ip dest:port)? - how to setting up Dude completly in PC & RB? I see many post for RB logging question but my idea is not perfe...

OrCAD

nice, this work perfecly...
For ICQ? I think only change the port... but for icq file transfert?
I'm waithing..
10x.

OrCAD

where to download file for test snmp logging?
10x

OrCAD

Hi,
I need to log, in file or snmp or vs IP, complete path of all user's,
now, how to send this information? es: src ip:port <-> dst ip:port
many 10x.

OrCAD

OrCAD

This script send to log source address and destination address?
For each lan port or wireless?

10x.
OrCAD

OrCAD

Hi,
I have AG2000w+ nomadix machine and give me out log into this mode:
internal IP <---> external IP (internet) - port used - time

Is possible to obtain this information in RouterOS log?
Is possible to send in log all information from Firewall-Connection window?

Thank's in advance.
OrCAD

OrCAD

oki I, seem work perfectly with this:

/ip firewall filter {disable [find comment="lock all P2P"]}

and

/ip firewall filter {enable [find comment="lock all P2P"]}

10x in advance 4all.

OrCAD

oki!

OrCAD

I have the same problem....
firewall rules don't disable or enable after scan the comment text!
Any idea?

many 10x

OrCAD

I see the manual and I try to create a script but not work... I have try to add this line in script submenù: to enable firewall rule 0 add name=enable-0 source={/ip firewall filter enable 0} to disable firewall rule 0 add name=disable-0 source={/ip firewall filter disable 0} this two line are contro...

OrCAD

any example for?

10x

OrCAD

Hello!
is possible to set a firewall rules to block P2P only from 08:00 to 23:59?
time regulation with NTP server.

10x in advance..
OrCAD

Search found 133 matches