Thanks for your response. Not sure why I have not gotten others? The 2 x CRS504's add the ability to connect the TrueNAS @ 100gb in a redundant fashion if I can use MLAG/LACP with the CRS326 switches it also makes those redundant across my network. My Firewall also supports LACP (802.3ad) as well so...

Are they other alternative transceivers that someone has used to connect a CRS326-24S+2Q+RM - 40G QSFP+ port to a CRS504-4XQ-IN - 100G QSFP28 port with fiber directly using a 1x12 MTP/MPO Multimode cable other than the XQ+85MP01D? The XQ+85MP01D is on the compatibility list: https://help.mikrotik.co...

Anyone have a sample config for a CRS504-4XQ-IN to work with some CRS326-24S+2Q+RM?

Looked on all the posts but don't really see much out there posted?

No responses?? Bummer

I have lurked for some time on this forum and own a few of the Mikrotik Switches/Routers now that I have acquired over time. I would like to simplify/yet automate my network config and consolidate into an all Mikrotik configuration if possible. My current Mikrotik Inventory: 2 x CRS504-4XQ-IN 2 x CR...

Please Add CRS504-4XQ-IN to this list as well! Thanks

Is it possible to use the MTP to 10 Duplex LC Breakout cables available to use one of these breakout cables available and get 10 separate LC 10gb connections? Plenum Fiber Optic Cable, 100 Gigabit Ethernet CFP/CXP 100GBase-SR10 to MTP(MPO)/LC (10 Duplex LC) 24 inch Breakout Cable, OM3, 50/125, 3 met...

Here is the high-level Network Diagram of what I am trying to do. Firewalla Gold + [4x2.5gb] Primary Function: Internet Firewall L3 Switch(Work VLANs) Mobile Devices Uplink to internet CRS326-24S+2Q+RM+ [2xQSFP+40gb & 1xSFP+10gb] Primary Function: L3 HW Offloading Video streaming - VLAN7(Video S...

Finally was able to finish this simple config. To get a simple access port/trunk configuration working. Now I need some help with locking down the VLAN filtering. Any links on a good way to make sure it is locked down? myconfig - clean.rsc Also getting a CRS504-4XQ-IN to drop in and do stateful fire...

First thanks for the quick reply. This is more of a bulletin board than a forum too many hard coded formatting fields and the quick buttons at the top do not work for me either :) As you can see by the time stamp on my message i don't really have time for formatting :) 1) Yes the interface lists are...

Just building this out but got stuck when i put on vlan filtering on the bridge. Did some searching but never found a complete answer. There is no IP on MGMT as I use a direct connect ethernet cable to the MGMT/BOOT port and connect via MAC. I could not find a similar config. I have HW offload turne...

I think your mixing up form and function. The MT Device is a switch and you clearly stated you have an upstream firewall that takes care of firewall rules etc. so not sure what the issue is?? Its a switch so Wire Speed should be a given. Security wise are you asking what additional security functio...

Currently I have CRS326-24S+2Q+ which I would like to use for HW Accelerated Bridging at Wire Speed and use filtering and stateless inspection with connection tracking. I have upgraded it to RouterOS 7.1.3 and I want to optimize both wire speed and security. I do have concerns on whether this is sec...

a) you can use default config as a starting point for your changes. And whatever you change, changes are saved permanently unless you do it while safe mode is enabled. b) depends. If you have a router (which will handle traffic between VLANs), then you shoukd keep using CRS as switch. If you don't ...

New to Mikrotik so just learning. I had a few basic questions: 1) CRS326-24S+2Q+ - I have upgraded my brand new switch to RouterOS 7.13 but wanted to ask some basic questions: a) It loaded a default config - should I change this? It is mentioned if i lose power that it will revert to the default con...