MikroTik

ihernandez

If you Need configuration Setup i will help you with it

Thank you Discmandj, I was just asking now so I can buy the CCRS. As soon as I get it, I will let you know so if I get into trouble you give me some pointers.
Best regards,

Ignacio

Gesendet von iPhone mit Tapatalk

ihernandez

Hi if the Port 1 will be for isp 1 witch Port will be for isp 2?

for ISP 2 the port used would be 24 (for example)

Gesendet von iPhone mit Tapatalk

ihernandez

Hi guys, it´s been a long time since I visited last time the forum and I see that a lot has changed! congrats on every improvements for the mikrotik crew. I have a few questions about the CCRS and the switch OS I have two ISPs and would like to use the CCRS to connect ports 2 through 9 to ISP1 and p...

ihernandez

i just tried it. It worked both ways. Paste the codes in a script and run to see if it works. Manually delete the ARP entry for 10.70.3.5 and then run the script. Thanks again Skillful, I will try it again tomorrow (saturday) wary in the morning so that the traffic is lower than usual Hello Skillfu...

ihernandez

i just tried it. It worked both ways.

Paste the codes in a script and run to see if it works.

Manually delete the ARP entry for 10.70.3.5 and then run the script.

Thanks again Skillful, I will try it again tomorrow (saturday) wary in the morning so that the traffic is lower than usual

ihernandez

1. Create a schedule to run at 10sec interval 2. Copy and paste the script below into the "On Event" box of the schedule { :if ([/ip arp print count-only where address="10.70.3.5"]=0) do={ /ip add set [find address="10.70.1.1/30"] disable=no } else={/ip add set [find a...

ihernandez

1. Create a schedule to run at 10sec interval 2. Copy and paste the script below into the "On Event" box of the schedule { :if ([/ip arp print count-only where address="10.70.3.5"]=0) do={ /ip add set [find address="10.70.1.1/30"] disable=no } else={/ip add set [find a...

ihernandez

Hi guys, I would like to know how to make a script to be run when a specific IP address is not detected in the ARP table. For example If ip addres 10.70.3.5 in arp table is not registered then enable ip address 10.70.1.1/30 and when ip address 10.70.3.5 is detected in arp table again disable ip addr...

ihernandez

Hi guys, I would like to know how to make a script to be run when a specific IP address is not detected in the ARP table. For example If ip addres 10.70.3.5 in arp table is not registered then enable ip address 10.70.1.1/30 and when ip address 10.70.3.5 is detected in arp table again disable ip addr...

ihernandez

Hi guys, I have this scenario: Two sites with two wireless links, ether1 and ether4 are used on the routers. I managed to add manually in routing>ospf>interface ether4 with a cost of 10 because I want it to be the primary and the backup is ether1 with a higher cost of 100. In ip>routes my router sho...

ihernandez

Hi guys, I have the same scenario. Two wireless links ether1 and ether4 to point b. I managed to add manually in routing>ospf>interface ether4 with a cost of 10 because I want it to be the primary and the backup is ether1 with a higher cost of 100. In ip>routes my router shows dst address 0.0.0.0/0 ...

ihernandez

Hello guys, I have a RB1100AHx2 and I've been using it as a DNS server and it's working fine. However some times the response is rather slow and would like to know what could be happening. I have blocked requests from the internet and only my clients can make DNS requests. The cpu has spikes up to 5...

ihernandez

Was anyone able to get this scenario working..??

Thanks!

I got this working, sort of.... still working out some issues with bluecoat

ihernandez

thank you for your reply, would this be enough? /ip firewall filter add action=accept chain=forward disabled=no dst-address=xxx.xxx.xxx.xxx dst-port=53 in-interface=ether1 protocol=tcp add action=accept chain=forward disabled=no dst-address=xxx.xxx.xxx.xxx dst-port=53 in-interface=ether1 protocol=u...

ihernandez

thank you for your reply, would this be enough? /ip firewall filter add action=accept chain=forward disabled=no dst-address=xxx.xxx.xxx.xxx dst-port=53 in-interface=ether1 protocol=tcp add action=accept chain=forward disabled=no dst-address=xxx.xxx.xxx.xxx dst-port=53 in-interface=ether1 protocol=ud...

ihernandez

Hello guys, I set up a Mikrotik as a DNS server and its working perfectly!. Now I would like to protect it from WAN queries, for example if the DNS query comes from WAN with dst to my DNS server block it.
Thank you for your help!

ihernandez

I have issues when the clients IP addresses are public. Do you have experience with CacheFlow?

ihernandez

Hello, I am looking for a mikrotik consultant. I am trying to implement a BlueCoat Cache Flow appliance and I need someone that knows about this and has had experience with web caching equipment.

ihernandez

You are right! thank you for your help

ihernandez

Hello my friends, I am having a bit of trouble with a policy based route. Here is the deal: The policy works when I use a single address just fine, but when I use a subnet it doesn't! I will post how its configured. Address List: /ip firewall address-list add address=192.168.162.111 disabled=no list...

ihernandez

Hi guys, than you for your replies!!!! I got this document from bluecoat and I need to translate this into mikrotik

Could you please help me do this?

ihernandez

Hey guys!, a hint? I am not sure how or where to start and would really appreciate your help on this

ihernandez

Hello guys, I would like to know if you could help me on this one!!! I just received a Bluecoat CacheFlow 500 appliance, super cool!!!, I assume I need a policy based routing rule in order to get this working, could you please help me? I plan to connect this appliance directly to a Routerboard 1200A...

ihernandez

Hello, finally I was able to recover the RB but I have to say that there may be a problem with that bactch of router boards. I purchased 3 and had to return 2 while I was in Miami because they stopped working after the upgrade. Then I tried to upgrade two and both got broken. I find this very strang...

ihernandez

Hi, I downloaded the firmware and I was able to upload it via hyperterminal. That is done and working. The problem now lies with netinstall. I am able to do a netinstall to other routers but with the 1200 that I am trying to unbrick it tells me that ehternet link is not present. I am getting the imp...

ihernandez

I am able to get into the routerboot through serial cable. It reads version 2.38. Then I hit o - boot device option in order to boot it through an ethernet port and then hit x in order to boot. Then it just stays there and throws a character and never responds again where could I get the firmware in...

ihernandez

Thank you for your help capital!, I will try this and let you know how it went I usually freak out when i have to upgrade a routerboard then system reboot. I procrastinate until i find i have to upgrade cause of security. I have lost my 1st Routerboard ever purchased RB1000. Then also bricked a coup...

ihernandez

I hope someone from mikrotik read this post quick, I purchased 3 rb1200. I opened the box, went into CLI terminal, input /system routerboard print to see if the current and the upgrade firmware was the same. It was not the same in all the routers, they were shipped that way. I hit /system routerboar...

ihernandez

Hello!, I have a routing question. I placed a mikrotik in a client with a static route dst=0.0.0.0/0 gateway=10.70.3.101. I have two sets of addresses in that router (1 set is private which I NAT) and a Public. The gateway 10.70.3.101 is part of an ospf core network. The problem is that the public a...

ihernandez

NV2 is TDMA based protocol that uses the channel more aggressively. It means that in most cases you effectively rule over the channel you are using, pushing out other interferers. Give it a try anyway. I have fixed that kind of problem such way..

Thank you taduikis, I will try this !

ihernandez

Most likely interference. Judging by 'poll timeouts', you use nstreme? If correct, try NV2. Otherwise you might need to try changing freq. Thank you taduikis I think interference is present, tomorrow I will change the frequency and see what happens. I use nstreme, why would NV2 be better if there i...

ihernandez

Hello!, I have had this link for about 2 years working flawlessly. Today it started disconnecting and throwing disconnection errors, attached you can see the errors. What could be happening and what could I do to diagnose and solve this.

ihernandez

I changed the channel to 20MHz, attached you can see what I get. Theoretically I am getting more P Throughput but my Tx CCQ is not as good as in 10MHz, I see a change in signal level as well as in noise floor. When I use the Freq. Usage tool in both towers of the link, it shows nothing that could be...

ihernandez

Hello guys, attached is a print screen with signal levels. The Tx varies from 78% up to 90% and the Rx varies from 95% up to 100%. The P throughput varies almost always is around 11mbit but sometimes drop down to 5mbits and goes up again to 11mbit. With these values what would be your advise to get ...

ihernandez

I will post results as soon as I get some tests done

ihernandez

Hello guys, I would like to ask you if this is possible or if any of you have had a similar experience. There is a glass building where possible clients have internet needs and called me (I own a small WISP). 500 meters away (aprox 1500ft) I have a node and could install a omnitik AP. The question i...

ihernandez

Hello, I am starting to deploy 4G airspan wimax equipment and would like to know if there is any drivers support for USB modems produced by greenpacket.com. The goal is to be able to install an USB modem on an USB capable mikrotik.
Please let me know if there is any information on this scenario

ihernandez

What is % of the loss? And have you tried pinging with size=500, 1000, 1450? Does the loss grow with packet size?

Hello dasiu, the % of the loss is about 1%, for size 500 and 1000, for 1450 it goes up to 4%.

ihernandez

Any chance that the IP address has been moved to the wrong interface? Its a really hard thing to troubleshoot from one line like that, what happens if you Mac-Telnet and reboot both sides? Have you done any hardware changes Firmware updates or so forth? Hello CyberT, I have rebooted both sides and ...

ihernandez

Hello guys, I am having an odd problem. I have a healthy wireless point to point wireless link ( signal -58, signal to noise -37, ccq 99%/100%, nstreme enabled, xr5 cards) the link has been working perfectly for the last year. Now I am having an odd behavior, when I ping from router a to router b (a...

ihernandez

Hello guys, I have installed a radius server and I have centralized authentication for hotspot users. When users login a dynamic simple queue is created with its specified speeds. What I would like to be able to do is to limit the amount of maximum bandwidth that all the users will use in total. For...

ihernandez

Interesting.... now I configured two 750G on v5rc5 (eth connected) and MPLS does not work. I tried dynamic / static neighbors.... all interfaces on a specific MTU and individually telling the router which interface had which MTU. I tried attaching supout.rif for mikrotik support but it is not possib...

ihernandez

Hello!!, I am having trouble with MPLS. If implemented on eth interfaces it works perfectly, if its configured over a wireless interface it does not work, when I say it doesnt work I mean the two routers communicate to each other but when I try to communicate from a pc going through both routers to ...

ihernandez

Good day everyone!, I am attaching a diagram of what I wish to accomplish. Its very simple, I wish to limit the speed to access internet per user with hotspot. I have several servers in my LAN and I do not wish to have my hotspot control the speed to which I connect to my servers (file server, apps ...

ihernandez

Just upgraded one of my routers in a VRRP cluster to 4.13 and get the same issue, change the priority and it turns to invalid :-( And there is no firewall rule blocking access to the router? If you are unsure, try disabling the firewall and change priorities once again. I just checked: It really is...

ihernandez

Any with a license level 4. A 750G should be able to handle 40 clients that only log in occasionally just fine, a 450G could definitely do it, anything above can, too.

Thank you fewi, +karma to you

ihernandez

I am having the very same issue, I opted to work with netwatch and enable/disable routes. VRRP on mikrotik has given us a lot of headaches....

ihernandez

Hello guys, I am attaching a simple diagram to what I would like to be able to do. The question is simple:

Which routerboard model should I use in this setup?

ihernandez

Hello, I am running into this very same behvior. I have two routers with vrrp, everything goes according to plan but when I test the vrrp (I unplug cables and then plug them back in) all hell breaks loose!, both routers go to RM and nothing works. I am running ver 4.13 on a x86 platform.
Help...

ihernandez

Great, how about lifespan and speed for the compact flash?

ihernandez

From my understanding, you wish to connect clients to a specific VLAN. If you're not sure or wish not to configure VLANs on the clients PCs and devices you should use untagged VLANs on the ports that connect directly to your clients. I hope this helps

ihernandez

Hello guys, I would like to know what are your thoughts / experiences on using a Compact Flash card for loading ROS on an x386 architecture. The reason for me to think about doing this is lower power consumption (currently I am using a p4 with a large power supply) and small footprint but high proce...

ihernandez

Now I upgraded a second one in order to see if the first one is a faulty router board and It has the same problem!!!

I now have two RB411AH with v5.0 and have CPU 100%!!

ihernandez

Hello my friends! I have a question. I am doing remote logging from my RB's to a dude server. I see that there are levels of details for logs but I haven't found a way to log detailed things, for example I would like to know which is the number of the simple queue I changed and what I changed or may...

ihernandez

Hello my friends I upgraded to 5beta5 a 411AH that I use on a point to point link. The only thing I have implemented in that router board is OSPF. Eventhough currently I am not passing traffic through this link the CPU usage goes to 100%. What do you think ? Would a supout help? Anyone from Mikroti...

ihernandez

Please anyone from mikrotik who could help me?

ihernandez

Does anyone know where I can get a good tutorial/documentation about bandwidth/QoS?

Hello elarrarte, you could start here http://wiki.mikrotik.com/wiki/Category:QoS in the wiki there is a lot of useful information.

ihernandez

Hello my friends I upgraded to 5beta5 a 411AH that I use on a point to point link. The only thing I have implemented in that router board is OSPF. Eventhough currently I am not passing traffic through this link the CPU usage goes to 100%. What do you think ? Would a supout help?

ihernandez

I just wish to know if I can use XR5 cards

ihernandez

Did anyone test the drivers?, I do not have available Dell servers so I can't test but Normis is right it appears nobody is testing so far

ihernandez

Any news about TDMA? this would be goooooood!

ihernandez

This would be interesting to know, anyone knows?

ihernandez

Hello guys, any thoughts about learning ros book?

ihernandez

I am having the same problem in 4.6, maybe a bug?

ihernandez

100% is not possible, your value is very good. Hello Normis and thanks for your reply!. I have to disagree with you on that since I have 2 links that show almost steady tx/rx CCQ 100% (the links are 11km and 15km). If you state that 100% is not possible, which would be the range for bad CCQ, ok CCQ...

ihernandez

please?

ihernandez

Any thoughts guys, this is a great point to know.

ihernandez

Any ideas please?

ihernandez

Hello I will first state my equipment: 2 x XR5 @ default power 2 x 29 dBi parabolic antennas 2 x 411ah RB 2 x 18 volt power supply and PoE Having said this, I cant get the CCQ to get steady up to 100% please see attachment so you'll know noise floor etc I have swapped all components to see if I had ...

ihernandez

Hello guys, something happened to my router. Its in production hence urgent in the message title!.

I logged into my rb433 and it gave me this error!! see the print screen!

What do I do!? the rb is in production!!!

I already followed the instructions and nothing changed

ihernandez

I think its possible too, I would be using XR5 and 33.4 dBi antennas which should give me a signal level at the RX site of -62.20 dBm

What do you think guys?

ihernandez

Hello guys, I would like to listen to your oppinions on this link: Point A Latitude 10°32'25.76"N Longitude 66°52'51.45"W Point B Latitude 11°47'21.53"N Longitude 66°36'42.09"W The link is 150Km in length, point A is a very high mountain about 2000 mts above sea level and point B...

ihernandez

Thank you very much!, I will try this.

ihernandez

Thank you for your response, what would you recommend for me to do if now I need to restrict my clients speeds. Both residential (broadband) and companies (dedicated speeds)

ihernandez

Hello guys, here is a print screen of a queue tree that I made in order to give priorities to different services. I do not know if this is the best way to do it so I would like to know what you think. On the other hand, I would like to do the same on the simple queues area but instead of priorities ...

ihernandez

Hello my friends I have two ISP's and both converge in my RB1000. What I wish to do is to force a specific subnet tha is in another node to find internet through the ISP I wish. For example, ISP A is used for dedicated internet access for companies. ISP B is used for residential internet access (Bot...

ihernandez

Yes. http://wiki.mikrotik.com/wiki/DNS To block outside access, simply add a firewall rule like this: /ip firewall filter add chain=input in-interface=<your WAN interface> protocol=udp dst-port=53 action=drop To block access to udp/53 via the WAN interface. Make sure you accept established/related ...

ihernandez

what functionality do you need from DNS?

Only basic functions, name resolution and DNS caching

ihernandez

Hello wise people!, I have a question for you:

I would like to know if its possible to use a routerboard with router os to substitute temporarily a DNS server. If the answer is yes, how would I do it and how would I protect it from being used outside my network.

ihernandez

Connect the ethernet interface of a RouterOS device to another device that does dot1q. Create a VLAN interface with the ethernet port as the parent, and apply the VLAN id you want (like creating a dot1 sub-interface on a Cisco router). Traffic from the VLAN network will go out the ethernet interfac...

ihernandez

Yes, the user service tag is q-in-q.

Hello fewi, thanks again. How do I tag a vlan in mikrotik?

ihernandez

Hello wise crowd!, I seek your help. I setup my mikrotik with VLAN 77 on it's eth1 as you can see on diagrams B and C and a WiMAX cell with VLAN 77 on its ethernet port (tagged only). If I check User Service Tag on my mikrotik VLAN (dawing B) the communication is lost, if I uncheck the User Service ...

ihernandez

Thank you fewi, it worked perfect!!!

ihernandez

Make an address-list containing the IPs of clients not permitted internet access, then drop packets from those clients out the WAN interface. /ip firewall access-list add list=no_internet address=10.2.0.0/24 add list=no_internet address=10.3.0.0/24 /ip firewall filter add chain=forward out-interfac...

ihernandez

I have a client and he has two services with me. One is Internet Access and the other is data between 4 offices. For internet access he uses public IPs and for data between offices he will use private IPs I would like to block the private IPs of that client from internet access. How would I do that.

ihernandez

Thank you for your response fewi, I will review the link you sent.
Any comments from Mikrotik???

ihernandez

Hello, I have managed to configure VLAN's in mikrotik and between mikrotik and mikrotik they work as intended, my headaches start when I introduce a switch. I am using a 3com 2226 plus and I can make them talk through VLAN but the behavior is strange. I will post later on today some of my problems, ...

ihernandez

I am about to buy dell used servers to load Router OS. The server processor is Intel CPU: 1x 64 Bit Intel Pentium D/830 Dual Core 3.0GHz / 2MB Cache / 800FSB My question is: Will I have trouble using ROS on this server because its 64bit, I know I wont use efficiently the processor since its a 64bit ...

ihernandez

Hello, I would like to know if I can use this cards with external dish antennas for point to point links

ihernandez

Set for the /radius configuration, 10.70.1.70 instead of 10.5.50.1 What do you see on the HotSpot logs ? Hello sergejs, I tried this before and I am able to authenticate but I dont go through the router itself after I authenticate. What I mean is that I am not controlled by the central hotspot serv...

ihernandez

Hello guys! I have installed hotspot and user manager on a PC L6 ROS. I have read all the wiki articles about centralized authentication with hotspot and user manager but still cant make it work. Please help. Here are some configurations from both USR manager and client router, in my network I use O...

ihernandez

Hello guys, I would like to know if I can use layer 7 on a rb433 without killing its processor. If rb433 hasn't enough juice, which one would you use.

ihernandez

Any thoughts please?

ihernandez

Hello guys, I seek your wisdom!. I have a queue tree that gives me priority to different kinds of traffic, here is the tree: /queue tree add burst-limit=0 burst-threshold=0 burst-time=0s disabled=no limit-at=256000 max-limit=500000 name=winbox_in packet-mark=winbox_in parent=global-in \ priority=1 q...

ihernandez

Make sure you have configured two DNS servers to /ip dns set primary-dns= secondary-dns= To reply for remote DNS requests set /ip dns set allow-remote-requests=yes Add redirect NAT rule for DNS traffic (port 53, protocol UDP and TCP), /ip firewall nat add action=redirect chain=dstnat dst-port=53 pr...

ihernandez

Hello guys!, I have a hotspot server on my network and I installed a DNS cache server on it. I would like the hotspot users and non hotspot users to be able to access the cache server on that router. How can I do that?, I think its a simple rule on that server (Firewall rule) but I dont know how to ...

ihernandez

I have a question about implementing correctly mangle/queue tree bandwidth management. I have this mangle on my firewall: 4 ;;; Client 1 UL chain=prerouting action=mark-packet new-packet-mark=client1_u passthrough=yes src-address=172.16.6.8/30 5 ;;; Client 1 DL chain=prerouting action=mark-packet ne...

ihernandez

Hello guys, I would like to share my latest link, it's a 15km point to point link made with XR5, RB433, Dish antenna 29 dbi. This so far is the best link I have in terms of CCQ and quality of wireless link. I would like to know how could I optimize it in terms of data throughput.

ihernandez

Thank you for your reply!, I will try this and let you know how it went Then you can do the same in Mangle. Just add the subnet to the source IP. Optionally (if you want to mark more subnets together) you can create an address list in IP/Firewall/Address List and refer to that list in Mangle/Advance...

ihernandez

Thank you for your reply but I need this to be a part of a queue tree.

Sure you can... But if you want to use simple queue, not even mangle is necessary, you can just create a simple queue with a limit and set the subnet as the source IP.

ihernandez

Hello telematics09, I was having the same problem however I was using ROS v3.22 and v3.10. I solved it by upgrading all routers to v3.22

I hope this helps

ihernandez

Hello guys, I would like to know if I can mark packets on a group of IP addresses. For example I have a xxx.xxx.xxx.xxx/40 on a router and would like to mark their packets in order to control their bandwidth. the setup is like this (bandwidth control) Subscriber module canopy <-----------> AP canopy...

ihernandez

ihernandez - Sure - there are a number of reasons..... Bad cable(s) or connections at the card(s). Bad cable connection from the card to the antenna (bad cable-loose ground, water intrusion, etc). Antenna damage. LoS issues, such as 'knife edge defraction', or an obstacle closer to one antenna than...

ihernandez

Hello, I would like to know if you could help me with this issue. On one side I have an ok signal level (good ccq 75% to 81%) and on the other I have a weak signal (see print screen)
I use XR5 on both ends I just changed them to make sure it wasn`t the cards.

ihernandez

Any thoughts guys?

ihernandez

Hello, I would like help here guys!. I haven't started this project but this is what I would like to have: A centralized user manager - This router os would be installed on a dedicated machine (IBM server) A series of wireles point to point links - I use only Mikrotik for wireless links and routers ...

ihernandez

Any thoughts guys?
Really need feedback because I have seen in other posts that the xr3 are prone to damage due to static

ihernandez

Hello and happy new year guys!
I would like to know what experience has any of you had with the Ubiquiti XR3. I am planning on buying a lot of 100 of this cards but would like to know what you think of them in combination with mikrotik RB 433 and a cpe RB.

ihernandez

23dBi patch antennas are good till 10km

How about 22 dBi grill antennas, both the grilled and the patch are hyperlinktech

ihernandez

Hello guys!, I need a little help here. This is my setup. On each side I have: one rb433, patch antenna (23dbi), 1m LMR 400 cable and SR5 running on 5300 MHz. The thing is that the signal strength is too weak. According to my calculations I should be getting around -82 and the according sensibility ...

ihernandez

THe ccq has improved over time by itself. However I see that the pings are 1ms and 2ms but it has occasional spikes up to 200ms, what could provoke this behavior.

ihernandez

Hello, is there a diagram to make from scratch a serial cable in order to access the routerboard to reset it?

ihernandez

Hello I have an 9 km link with one solid dish 29dbi on each location. The wireless card I use is an SR5 on default tx power, and for routerboard I use RB433. Attached is a printscreen of my throughput (which I am happy with). I would like to know which tweaks (if any) I could use to get a better CCQ...

ihernandez

Thank you Normis, I will try that

ihernandez

Hello, I would like to know how can I schedule a change on a simple queue:

For example, I have a simple queue that has a target dowload/upload of 1mb and on a certain hour of the day I would like to change it to 3mb.

Thank you for your help

ihernandez

where is ANI in advance tab...i cant see the premabe type but i m not abl e too see adoptive noise immunity. i m usiing ROS 2.9.38

The first thing you should do is upgrade your ROS, and in advanced tab you should be able to find what you're looking for

ihernandez

On one rb use bridge mode on other station wds. Use clearest turbo channel with nstreme enabled on both devices. On bridge device set nstreme framing policy to exact size. Also in advanced tab use long preamble, and adaptive noise immunity. ANI adds about 2-4 Mbps. If you get good signal strenght, ...

ihernandez

Hello, I am installing one important link on my wisp and I will be using this link as part of my backhaul. I would like to know which would be the best configuration for highest throughput (AP to station, pseudo bridge, etc) I don't need to route on the mikrotiks that I am using to make the radio li...

ihernandez

Hello, I have the following configuration for an Access Point: rb433, xr5, sector antenna - 19dbi I would like to know how many subscribers can I give service to with this configuration. On the subscriber side I would be using a NANO 5 Stations. Regards, Ignacio How much bandwidth will be allocated...

ihernandez

Hello, I have the following configuration for an Access Point: rb433, xr5, sector antenna - 19dbi
I would like to know how many subscribers can I give service to with this configuration. On the subscriber side I would be using a NANO 5 Stations.
Regards,

Ignacio

ihernandez

Hello, I would like how to solve a problem that I am having: I use hotspot for my residential clients, I would like to give a username for each person that lives on a given apartment. The problem comes when I specify the amount of bandwidth that I am allocating for each apartment, in example One apa...

ihernandez

I have RB433AH ROS 3.13, firmware 2.16 using 2 x XR5 in dual-nstreme mode. the voltage is 11V, standing still when the cpu is set to 680MHz everytihng is ok but when I set it to 800MHz the RB works for a while and then reboots there is nothing wrong in the log I don't know if the watchdog is going ...

ihernandez

-----
Hello fren,

are you working with mikrotik's. . . . ?

regards
Hasbullah.com
-----

Yes, I have 10 mikrotiks and over 15 wireless links.
Regards,

Ignacio

ihernandez

Hello, I have the same question but for the radio links. Is there a way to see the serial number for the wireless cards

Regards
Ignacio

ihernandez

Hello, is there a way to get through CLI the serial number of the routerboard. If not, is it possible in any other way?
Regards,
Ignacio

ihernandez

what antennas are you using? Check the pigtails. Make sure you aligned the polarity of the feedhorn to the polarity of the grid. Make sure you are using a for main on the pigtail or b for aux connector. Can you see the other side with your eyes? Also grid dishes are hard to aim and usually only hav...

ihernandez

how long is your cable? is the visibility clear? did you use snooper to scan what frequency is most free? did you set transmit power to "default"? did you try "/interface wireless reset"? Hello, my cable is 6ft long, the line of sight is clear, I did use snooper and got that 518...

ihernandez

Hello, I am having trouble making a 5km link. I am using 2 grid antennas 22bi, and 2 rb52. Vertical pol. The signal strength is low, it varies from -78 to -81 and the longest time it has been connected without dropping the connection is about 3h
What can i do?

Regards,

Ignacio

ihernandez

the restore button is there if you double click on the actual file. they just moved the button. however its broken in 3.11. MT confirms this will be fixed. for now i was able to use the CLI to restore a backup.

Hello, I would like to know which is the CLI sequence to restore a backup.
Thank you

ihernandez

Thank you, will do this and let you know how it went

ihernandez

"make sure you are using latest RouterBOOT and RouterOS v3.11"

Hello, I would like to know how do I upgrade to the latest RouterBOOT

Thanks

ihernandez

Hello, thank you for taking the time and letting me know how to do this. As soon as I do this, I will post my results
Regards,

Ignacio

ihernandez

Thank you again for your reply, since I am a little new to mikrotik and minipci.. could you be more specific on how to do this?
Regards,

Ignacio

ihernandez

How do I know if they are propperly aligned?
How do I use the Align button, do I use it from the subscriber?

ihernandez

Thank you for your prompt reply,when I change the cards:
How do I know if they are propperly aligned?
One is configured as AP bridge and the other one as station, is there a better way to configure this if its a point to point link?
How do I use the Align button, do I use it from the subscriber?

ihernandez

For antennas I use dishes 29dbi I have a pair of Engenius Model name: EMP8602 Plus-s How can I optimize this? Where should I make the changes in winbox in order to improve ccq % rate? How do I know if they are propperly aligned? One is configured as AP bridge and the other one as station, is there a...

ihernandez

Thank you, do you recommend that I use an amplifier with this setup?
Regards,
Ignacio

ihernandez

Hello, I would like to know if you could point me in a right direction. I need to make a 17 km wireless link and would like to know what antennas should I use as well as the best wireless mini pci suited for the job.
I have a clear line of sight.

All your comments are welcome!!!

Regards,
Ignacio

ihernandez

Hello, I have a question about an Ubiquity card, the XtremeRange3 2.7-3.7GHz. Can I use this card with mikrotik routers, if so, which is the best mikrotik router for this card and which is the best antenna for this card. The approx length of the link is 15 km and the reason for me to choose this car...

ihernandez

Thank you for your reply, how would I set it up and what tests do I have to do to ensure its working
Regards,
Ignacio

ihernandez

Hello, I have a question about what exactly is DFS mode and how do I implement it. I have not found Info about this on the forums. Apparently everyone has it on dfs mode=none
Regards,

Ignacio

ihernandez

Thank you for your support, I will let my supplier that what he sold me is pure junk!

ihernandez

I'm I better off with a R52H from mikrotik for a 4km link?

ihernandez

To start, you need to upgrade your ROS to the latest version. Your signal strength will not give a reliable connection. Buy yourself a couple SR or XR5's and you will be fine. Is the signal too strong? or is it just that the minipci cards are not good?, Can I modify manually the signal strength? Re...

ihernandez

Continuing with my posts, I am including some printscreens with the info that follows: I have two buildings connected 4Kms appart (aprox) signal strength -88 dbm Noise Floor -95 dbm overall tx ccq oscilates from 10% to 50% and somtimes the connection is dropped I should have nstream disabled right? ...

ihernandez

That is a horrible card to use for 5ghz. Get a R52h or XR5

Thanks for the info, which one is better for distances no longer than 20km?
For antennas I use dishes 29dbi.

Thank you,

Ignacio

ihernandez

The wireless card:
Engenius
Model name: EMP8602 Plus-s

ihernandez

5413 doesn't tell me anything. What make/model are the cards?

The info that is shown in the winbox about the card type is: Atheros AR5413
Is this enough or you need more info. Where can I find more info about the cards?

ihernandez

What type of radio are you using? Atheros AR5413 5745 Mhz What is your signal strength? I Will post this later on because the link is down What height are your antennas? One is on top of a 10 story building which is on top of a 400 mts hill The other one is a 8 story building Do you have clear line ...

ihernandez

Hello, I have successfully installed 2 RB333 on each there is a wireless minipci card and each rb333 is located on a different building. The distance between the buildings is about 4 KM. I used 24dbi dish antennas. The link behaves perfect when it doesn't rain, however when it rains it is not too re...

ihernandez

Hello cmit,

If you would be so kind to mail it to me too !

thanks in advance

ihernandez at c-com dot net dot ve or
ignaciohernandezr at gmail dot com

Search found 151 matches