Community discussions

MUM Europe 2020

Search found 22 matches

by GP01Fb
Wed May 21, 2008 11:11 pm
Forum: Wireless Networking
Topic: ARP reply couldn't get through
Replies: 3
Views: 1300

Re: ARP reply couldn't get through

Thank you for your reply. But now I have more questions: 1. What is station-pseudobridge mode? I couldn't find it anywhere. Could you please provide me a step by step setup about this? 2. What do you mean by "it should work fine for one client"? This is only the phase 1 of my project, and in phase 2...
by GP01Fb
Wed May 21, 2008 11:08 pm
Forum: General
Topic: station pseudobridge in 3.x
Replies: 6
Views: 8711

Re: station pseudobridge in 3.x

I would like to setup my MikroTik router in station-pseudobridge mode too, but I don't know where to start. Can anyone provide a step by step setup guide? Thank you very much for your help.

Horace
by GP01Fb
Wed May 21, 2008 4:51 pm
Forum: Wireless Networking
Topic: Wireless connection problem
Replies: 8
Views: 1336

Re: Wireless connection problem

Thank you very much. But I cannot setup the dhcp server correctly. I followed the doc but it's not working. Can anyone provide a step-by-step setup instruction. Your help will be appreciated.
by GP01Fb
Wed May 21, 2008 4:46 pm
Forum: Wireless Networking
Topic: Urgent!!! Newbie questions regarding wireless connection.
Replies: 10
Views: 1523

Re: Urgent!!! Newbie questions regarding wireless connection.

How to setup the Dhcp server? I followed the doc but it's not working: /ip pool add name=dhcp-pool ranges=192.168.1.2-192.168.1.254 /ip dhcp-server network add address=192.168.1.0/24 gateway=192.168.1.1 /ip dhcp-server add interface=wlan1 address-pool=dhcp-pool 192.168.1.0/24 is the subnet the ether...
by GP01Fb
Wed May 21, 2008 10:14 am
Forum: Wireless Networking
Topic: Wireless connection problem
Replies: 8
Views: 1336

Re: Wireless connection problem

I cannot see the dhcp-client at winbox. Is there any other solution? Thank you.
by GP01Fb
Wed May 21, 2008 10:06 am
Forum: Wireless Networking
Topic: Urgent!!! Newbie questions regarding wireless connection.
Replies: 10
Views: 1523

Re: Urgent!!! Newbie questions regarding wireless connection.

How to do the routing then? Below is my configuration but it's not working. Is there anything wrong? IP: Address: 192.168.1.70 Network: 192.168.1.0 Broadcast: 192.168.1.255 Interface: wlan1 Route: Destination: 192.168.10.0/24 Gateway: 192.168.1.70 Check Gateway: ping Scope: 255 Target Scope: 10 Pref...
by GP01Fb
Wed May 21, 2008 1:05 am
Forum: Wireless Networking
Topic: Urgent!!! Newbie questions regarding wireless connection.
Replies: 10
Views: 1523

Re: Urgent!!! Newbie questions regarding wireless connection.

If that's the case, then how can I connect the router board to my router?
by GP01Fb
Tue May 20, 2008 11:42 pm
Forum: Wireless Networking
Topic: Wireless connection problem
Replies: 8
Views: 1336

Re: Wireless connection problem

Yes.
by GP01Fb
Tue May 20, 2008 10:37 pm
Forum: Wireless Networking
Topic: Wireless connection problem
Replies: 8
Views: 1336

Wireless connection problem

Is it possible to connect the router board 133c3 to regular wireless router? (e.g. linksys, d-link, etc...) If so, how to configure the router board and/or the regular router so that my pc can surf the web wirelessly? Below is the setup which I want to construct: PC ---(cable)--- Router Board 133c3 ...
by GP01Fb
Mon May 19, 2008 7:08 pm
Forum: Wireless Networking
Topic: Urgent!!! Newbie questions regarding wireless connection.
Replies: 10
Views: 1523

Re: Urgent!!! Newbie questions regarding wireless connection.

Thank you Egate. That's what I think too, but I just can't ping from one side to the other (both direction). Did I miss out anything for the configuration? Again, I've set the wlan1 interface in station mode; band, frequency and ssid matched with my other router; add bridge1 and two ports for both e...
by GP01Fb
Mon May 19, 2008 12:39 pm
Forum: Wireless Networking
Topic: Urgent!!! Newbie questions regarding wireless connection.
Replies: 10
Views: 1523

Urgent!!! Newbie questions regarding wireless connection.

I would like to setup the network as follow: PC1 ---- (ether1 -- bridge1 -- wlan1) ---- router ---- PC2 (or internet) RouterBoard 133c3 Basically I would like to use the RB so that the PC1 can have wireless feature, and then it can connect with a generic wireless router which connects to PC2 or the ...
by GP01Fb
Fri May 16, 2008 12:36 pm
Forum: Wireless Networking
Topic: ARP reply couldn't get through
Replies: 3
Views: 1300

ARP reply couldn't get through

Hello, I've set up the network as follow: Laptop A connects to the router board 133c with cable. Laptop B connects to another router with cable. (just normal router purchased at retail store). The two routers are connected wirelessly. I run wireshark to keep track of the traffic and I discovered the...
by GP01Fb
Thu May 15, 2008 9:13 am
Forum: General
Topic: Help!!! Router has been disconnected!
Replies: 2
Views: 2630

Help!!! Router has been disconnected!

When I was testing the router, it suddenly started to lose connection. I tried to restart the winbox and the router several times but it didn't help. I then reset the router but the problem still there. After I login with winbox for a few seconds, the error message "Router has been disconnected!" po...
by GP01Fb
Thu May 15, 2008 2:26 am
Forum: Wireless Networking
Topic: wlan1 setup
Replies: 1
Views: 881

Re: wlan1 setup

Just want to point out that I've ping from my PC to ethan1 to wlan1 and it can get through. So the problem should be the wireless connection.
by GP01Fb
Thu May 15, 2008 2:23 am
Forum: Wireless Networking
Topic: wlan1 setup
Replies: 1
Views: 881

wlan1 setup

Hello, I would like to setup my RouterBoard 133c wlan1 to connect to my other wireless router (just a normal router purchased at retail store) connected to the DSL modem. The reason to do this is to make my PC connect to the internet through RouterBoard wirelessly. However, I cannot setup the wlan1 ...
by GP01Fb
Mon May 12, 2008 11:49 am
Forum: Wireless Networking
Topic: wireless client and proxy ARP
Replies: 1
Views: 1012

wireless client and proxy ARP

Hello, I wonder how to set up the router as a wireless client. Also, how to set up proxy ARP to the router? I'm using 133c RouterBoard. Thank you very much.
by GP01Fb
Fri May 09, 2008 10:07 pm
Forum: Scripting
Topic: Save script source file
Replies: 3
Views: 1686

Re: Save script source file

I use winbox to write script and the scheduler. However when I reboot the router, winbox will automatically close and I don't know whether my startup script can be executed at startup. Any suggestion? Thank you very much.
by GP01Fb
Fri May 09, 2008 9:58 am
Forum: General
Topic: Web Server
Replies: 3
Views: 779

Web Server

I would like to install a web server application to the Router. Can anyone suggest one? And how can I install that to the router? Please advice. Thank you very much.
by GP01Fb
Thu May 08, 2008 8:56 pm
Forum: Scripting
Topic: Send package
Replies: 1
Views: 834

Send package

I would like to make the router to send out a package everytime the router starts, is there a way to do that? Please advice. Thank you very much.
by GP01Fb
Thu May 08, 2008 8:52 pm
Forum: Scripting
Topic: Save script source file
Replies: 3
Views: 1686

Save script source file

I need to write an auto run script so that it will run everytime the router starts. How to do that? Should I write the script as a file and save it in the router's memory? If so, how to save the file in the router's memory? Please advice. Thank you very much.
by GP01Fb
Wed May 07, 2008 11:42 pm
Forum: Scripting
Topic: Auto Run Script
Replies: 1
Views: 1892

Auto Run Script

Hello everyone,

I'm new to the RouterOS and scripting and I need some help. I wonder how to write some auto run script. Please advice. Thank you very much.