Dear, my router OS generate ghost traffic from my users! I changed the DNS for my DNS servers, but the traffic is yet, theys generate traffic to googles DNS and my DNS servers. I'll like anybody help me about this?

Router OS version: 6.44.3
Hardware: CCR1009-7G-1C-1S+


Thankyou

In other side there is no interference, because it is in the jungle, no radios, no wifi.

Have you good Fresnel clearance on this link?

Yes.

Don't forget that you're using a 40mhz channel which is more susceptible to interference. Suppose that your receiver is located near another receiver on a similar channel - did you do your spectrum analysis at the client site? Yes I did. I''ll try change to 20mhz channel. I think this really is int...

Don't forget that you're using a 40mhz channel which is more susceptible to interference. Suppose that your receiver is located near another receiver on a similar channel - did you do your spectrum analysis at the client site? Yes I did. I''ll try change to 20mhz channel. I think this really is int...

Do you have more radios near by? It looks like interference to me.

There is some radios, but not in same channel. The frequency usage show me that don't have used channels.

Dears

I have some problem in my wireless link. The signal is strenght, CCQ RX is 98/100% and low CCQ in tx rates ( 37, 44%). I tried anything, change channel, modulation, etc. I need help

Thank you

Which RouterOS version are you using? 6:33.3 Firmware version? (see System >Routerboard?). routerboard: yes model: 1100AHx2 serial-number: xxxxxxxxx firmware-type: p2020 current-firmware: 3.24 upgrade-firmware: 3.24 I'd open the cover to inspect the fan is actually properly plugged in place. Everyt...

the CPU temperature is high ( see bellow). Any solution or the fan is broken? [xxx@Server ] /system health> print fan-mode: auto use-fan: main active-fan: none voltage: 12.1V current: 865mA temperature: 33C cpu-temperature: 65C power-consumption: 10.4W fan1-speed: 0RPM The temperatures are normal r...

The url is broken.

Dears Merry christmas I have the problem on my RB100 AHX2, the fan stoped, and the CPU temperature is hight ( see bellow). Any solution or the fan is broken? [xxx@Server ] /system health> print fan-mode: auto use-fan: main active-fan: none voltage: 12.1V current: 865mA temperature: 33C cpu-temperatu...

try HT MCS 12 or HT MCS 13 with auto tdma on ROS 6.19 (6.25) with wireless fp package. signalstrength should not be worse than -70 (all in range 60-70) So if I've some interferences 16QAM is better than QPSK? No, the QPSK is better in environments with interference than QAM Try it: 1 - Set only mod...

Dears friends

I'm need a PtP of 70 km (see attached image), and I need to know if QRT5 close this PtP, the troughput must be 15Mbits halff. . Low Noise and LOS




Thanks to all

Friends I need your help. Here's the problem: I have a switch CRS125-24G-1S-RM and need to configure it so that all other ports see only ports 1 and 2, and they see each other. Any way to help me?


Thxs all

Sorry my english.

there is no bug - if you use "both-addresses-and-ports" you will get such problems for sure. you need to use "both-addresses" Thanks! But, for my experience, the both-addresses adjust does not add the links, it just makes balancing! In my case I have tree links of 10 mbits, when...

Dear I´m new by here! Well, I am implementing a Load Balance with PCC, and wondered if the "bug" in both-address and ports at the 3.27 version (Per Conection Classifier) was corrected in 3.30? Because this was not before loading youtube, it was necessary to press the regarregamento browser...

Thanks all, Regards

Dears, I´m new user here, and I change my POPs of Staros V3 to MK :lol: :lol: :lol: ! In this case I need make the link of 73 Km but with non line of signal, and i think that use the XR9 or XR7, but I ca´nt if is possible because many montain that see bellow the pic of Motorla link estimator - only ...