Community discussions

MUM Europe 2020

Search found 12 matches

by jbowsher
Thu Jan 06, 2011 9:46 pm
Forum: General
Topic: I can log-in using winbox but everything is empty.
Replies: 6
Views: 2375

Re: I can log-in using winbox but everything is empty.

I experience this problem too, but i know that it is more than a pc problem because when it happens i have customers complaining of slow speeds or high latency and people who are not already authenticated in radius via pppoe cannot login. I have experienced this on both RB600A's and RB433AH's (each ...
by jbowsher
Mon Oct 11, 2010 9:35 pm
Forum: General
Topic: MAC auth with Radius
Replies: 8
Views: 1626

Re: MAC auth with Radius

I have it working fine utilizing hotspot mac auth but the problem is people will get one address from the hotspot controller and then a different address from the dhcp server and then all the sudden the user gets the hotspot login page and we have to kick them from the hotspot hosts tab and then the...
by jbowsher
Fri Oct 01, 2010 8:53 pm
Forum: General
Topic: New wireless protocol: Nv2 in v5.0beta5
Replies: 217
Views: 79682

Re: New wireless protocol: Nv2 in v5.0beta5

I have it setup that way but it is only using 20 Mhz Channel from what i can tell. I get about 190 Mbps tcp one way and about 95Mbps tcp bi-directionally but i know it would be twice that if i can utilize 40Mhz channel width. I started trying to test Nstreme dual with N today but I must say that my ...
by jbowsher
Fri Oct 01, 2010 1:30 am
Forum: General
Topic: New wireless protocol: Nv2 in v5.0beta5
Replies: 217
Views: 79682

Re: New wireless protocol: Nv2 in v5.0beta5

Can anyone tell me why i cannot select 40Mhz channel width on the wireless interface in routeros v5 rc1? It doesn't seem to matter what cards I use or what band I set it to, it always shows the error "Couldn't change interface <wlan1> - incompatible band and channel-width (6)" I tried every band on ...
by jbowsher
Thu Jul 01, 2010 9:42 pm
Forum: Wireless Networking
Topic: 802.11n
Replies: 939
Views: 292789

Re: 802.11n

wasn't looking for a prize.....I was a little shocked with my results as they were the best I've seen but I felt that it was still less than adequate for 5ghz-N and I was looking to see if anyone had gotten closer to the 200 Mbps mark than I had. I am curious why everyone uses RB800 or RB433AH's sin...
by jbowsher
Wed Jun 30, 2010 7:06 pm
Forum: General
Topic: MAC auth with Radius
Replies: 8
Views: 1626

MAC auth with Radius

I am trying to do mac authentication with Vircom Radius and have the AP send over the client's wireless mac as the username and no password. The problem that I run into is when the CPE boots it starts the accounting request and completes that but it never sends an access request. If i make changes t...
by jbowsher
Wed Jun 30, 2010 6:53 pm
Forum: Wireless Networking
Topic: 802.11n
Replies: 939
Views: 292789

Re: 802.11n

anybody seen one direction bandwidth tests resulting in 346Mbps UDP and 140Mbps TCP? Thats what I was getting yesterday with my sr71's and was curious if anyone else has seen better results? :shock:
by jbowsher
Fri Jun 11, 2010 6:10 pm
Forum: Scripting
Topic: UPS power monitor script errors
Replies: 6
Views: 2648

Re: UPS power monitor script errors

I got it working a while back just never posted to let you guys know. It works like a top and when you have equipment on grain elevators where power is on and off a lot in the spring and fall it is nice to know when it switches to battery power via txt message! Thanks for all the posts!
by jbowsher
Fri Jun 11, 2010 5:35 pm
Forum: Wireless Networking
Topic: 802.11n
Replies: 939
Views: 292789

Re: 802.11n

I have tried everything from one card with only one chain to bonding 2 eoip tunnels and i cannot achieve anywhere close to the speeds that you guys are seeing. I have tried the forum configs that everyone has been using. I have even tried using MPLS/VPLS tunnels and i am at wits end. I am using 2 ra...
by jbowsher
Wed Jun 10, 2009 5:32 pm
Forum: Scripting
Topic: UPS power monitor script errors
Replies: 6
Views: 2648

Re: UPS power monitor script errors

It says line 26 is the culprit...I really need some help with this, thank you in advance for any possible solutions
by jbowsher
Thu Jun 04, 2009 11:16 pm
Forum: Scripting
Topic: UPS power monitor script errors
Replies: 6
Views: 2648

Re: UPS power monitor script errors

Here is a copy of the script, I just removed the mail server and made up a mail from address to post here, but basically when it gets to {:set curonbatt $"on-battery"; :set curcharge $"battery-charge"} it then highlights all the c's and m's in the script that are after "$" and gives errors for each ...
by jbowsher
Wed Jun 03, 2009 1:04 am
Forum: Scripting
Topic: UPS power monitor script errors
Replies: 6
Views: 2648

UPS power monitor script errors

I am using the ups power monitor script that I found on the mikrotik wiki for RouterOS ver. 3.x, but when I try to run it on a RB433AH with RouterOS ver. 3.23 it gives me several syntax errors and in the notes of the script it tells me not to modify the section that is giving me the errors. If anyon...