maybe is the offset 3 db offsetRB751U-2HnD has two chain 'n' wireless chip.
27dB per chain gives 30dB total.
Set Tx power to 27dB and check 'Current Tx Power' tab in Winbox.
the focal point doesnt change by frequency its depend of the size and form of the reflector..Not to go off-topic, but how do yo calculate focal point as it's slightly different for each frequency(band)?
yes it does im using itDoes anyone know if the stock RAM is capable of running at 533 MHz?
I might consider a RB1100 as suitable replacement for dying RB1000's if I can reliably clock them to 1333/533 MHz...
the RB600 has 64mb and RB600A has 128Than you should be asking how to fix those routerboards to show 64MB instead 128MB
Seriously, the spec sheet shows what you should get, anything more you can consider as a bonus. For example I have old RB433AH with 512MB and new with 64MB...
they are working on in a rb750 with wireless interfaceHi, i want to replace my (home) acces point. In the past there was talk about a wireless unit similar to the rb750g. Any progress in that area ?
thanksnice solder job!
if you can change it to IP175C/E u can confirm for sure that is a a bug,No one can confirm it? Ive sent supouts... Ive said... Guess nobody even notice this bug! *sigh*
ok, I got it, did u contact to mikrotik? sending email to support to confirm that?As I said, IP175C is working great. Ive found this occasionally implementing MPLS VPLS... guess I will need at least 1526 L2MTU.
ive two olds 3.5 alvarion XL and I can use the build in 23dbi antenna, did u try it with in turbo mode ?20.5Mbps in both directions at the same time using tcp
i am using the full 20MHz channels
how much bandwith do u get with it?I have a 5 mile link running these:
http://www.roc-noc.com/product.php?prod ... =38&page=1
I am seeing -60db so you might need to turn down the power at 2 miles.
im trying to fix the ether1 (PORT1) for later fix it the OS with netinstall. remember ive ether1 damagedIP175C and IP175D it's not replacement from software viewpoint.
maybe is ur simple queue. disable whole and test it againI used mikrotik on pc-router, connect by hub to lan wired 7 pc, before i'm using mikrotik v 3.28 ping time is 1 ms.. its normal?
yes but generally in internet we user smaller packets 64 bytesLook closer. It says 777 Mbps with 1500 byte packets.I guess the RB450G wont support that bandwidth, according to the test-april-2009 the board can just support upto 60 Mbps routing
can you show me the default TX power of your card?Dont worry, i had Compex WLM54AG-23 (23dBm) card. and i could run it on max (30dBm) without any problems.
I guess so, 'cause it managed by the routerOSDears,
RB 800 supports wireless compression like a RB 600?
Can you take photos of the hw inside.. thanks.. what kind of switch chip does it use?They just arrived yesterday and we ordered them the day they were announced to distributors. So don't expect any real world experience other than "yes, I touched one, I plugged it in and it works".
i did it right but there are no peep and the device does not work right too
the Ethernet led dose not flash when the cable is plugged too
anyideas?hi.. how can I create a pseudo VLAN over wireless... like some hotspot AP has...
acording what a read, it assign a vlan per mac-wireless (customer) so u can create a vlan per customer
any idea to make this in RB333 or RB433 ?
that email script is cool. i have realized the whole thing in a different way. i have nagios polling the voltage via snmp and give an alarm via email and sms if the voltage is out of normal values. that work fine for me.