MikroTik

dingsingo

Hi,

I'm looking for a solution in the CRS 328 & CRS 326 to want everything except the default vlan1 switch. What do I have to set that n tagged packets are forwarded?
But I don't have to store each individual vlan in the switches.

THX

dingsingo

Hello,

we are looking for a replacement fan supplier for the CCR1072. The code of the fan is probably PF40281B2-Q02U-S99. Can you give me anyone a source where I can get these?

Thx
Dingsingo

dingsingo

do you think it makes a difference whether I'm running V6 or V7 on the devices?

dingsingo

Hello,

I'm currently using a CCR1072 and a CCR1036 for the PPPoE session for around 2000 users, each with 1000 active users. Now I would like to improve the performance when processing the PPPoE sessions. I buy two CCR2116. or should I better use two 1072 and install the V7.x on it?

dingsingo

Just confirming when you said the firmware was the same, do you mean the router OS and firmware or just the OS, it can be a bit confusing as the firmware is included with the OS but not installed until you run the upgrade option form the routerboard menu then reboot :) Yes, both the same. After the...

dingsingo

Are the same type of sfp/sfp+ modules installed in both devices? The temp reading (not cpu temp) on a number of switch models comes from the sfp/sfp+ modules themselves. I have about 50 of the switches and they all have the same 24 SFPs from Edge Optics in them. So it can't be that. Some show the t...

dingsingo

Are the blades spinning? When was the last time you blew them out? Are the fans stock or third-party? I have the 24P version, so maybe your 20S differs, but mine uses 3-pin PC type fans. If you use 2-pin fans, you lose speed control. 2-pin fans should run full-speed, but that shortens their life, w...

dingsingo

Hello, we have a problem with a part of our CRS-328-4C-20S-4S+ switch. Although the same firmware is active on all and the bios is the same. We can't read the temperature of some devices. As far as we have been able to determine so far, this partly ensures that the fans are not controlled correctly ...

dingsingo

Yes, we would be very happy about a switch with 24 CSPF. Or alternatively one with 48 ports.

We have already installed 150 pcs. of the CRS328-4C-20S-4S + RM in 2020. We then had to install other manufacturers at larger locations because the 24 Port 328er take up too much space.

dingsingo

I'm looking for a script that gives me the total number of all active ethernet ports in a CRS328. Of course, it would be best if I could include that as part of the dude. Does anyone have any ideas about this?

Thx
dingsingo

dingsingo

Hello, have a problem here with anncouning a prefix via BGP. Another AS is attached to my public AS. From there I am currently receiving a /24 prefix. But it can also be a different one on the total of /22 large. So I set a filter with action=accept chain=bgp-out prefix=1.2.3.0/22 \ prefix-length=22...

dingsingo

..... Please enable BGP on ROSv7....

dingsingo

the fans are not idle, they only seem to be activated in an emergency. I have to try to measure power consumption when I can find the time.

dingsingo

Hi, For those who want to know more about 2004. just got the first one in the mail. An ARM64 is installed, the ARM firmware package for the ARM, which was previously linked on the MT side, does not run there. There is probably something here for the 64bit version. According to MT, the 4GB memory in ...

dingsingo

Hi, we have currently processed a CCR1072 in use of the 4 full and a few more peerings. 2.6GB are currently used there. I will test the 2004 times, but I suspect that even with the 500Mhz more clocking, the calculation of the table only gets a little faster. Our biggest problem is when one of the up...

dingsingo

Hi,

is known if you can use more than 4GB in the CCR2004-1G-12S+2XS ? For BGP, 4GB is not that much. Unfortunately I found a picture of the board itself on the net. My 2004er ordered is still on the way to me. Because you can surely use a DDR4 bar with 8GB?

Thx
Dingsingo

dingsingo

Show this one, http://shop.meconet.de/Systeme-Embedded/MikroTik/19-Zoll-Systeme/meconet-High-Performance-Router-HPR-1156-6GC::115816.html and http://shop.meconet.de/Hardware-Einzelteile/Netzwerkkarten/PCI-Express/4-Port-PCI-Express-Gigabit-NIC-4-SFP::115530.html and this 10G SFP http://shop.meconet....

dingsingo

this gives them something new ??

Thx

dingsingo

dingsingo

Hi,

*) Wireless problem fixed

is it broken in 5.15 or the Version before ??

Thx

dingsingo

dingsingo

Hi, or do you use this one: Mars 19dB Dual incl. Case: MA-WA56-DP19SMES 115498_0__115498-1.jpg Shop: http://shop.meconet.de/Antennen-Zubehoer/5-GHz-U-NII/WLAN/Richt-Antennen/19dBi-Panel-DP-DS-16-GRAD-H-16-GRAD-V-2-SMA-fe-MA-WA56-DP19SMES-inkl-Case::115498.html And in the Case a RB/711GA. dingsingo

dingsingo

I think that MT didn't now what the WISP wanted. We looks for good Products and in the second time on the price. When the Board is 3$ more expensive it is NOT the problem for WISP. But when we have a downtime on a Board, then irritation buy the customer is bigger then 3$. The Client's comparatively ...

dingsingo

hi,

my think, LC-Connector will by standard.

dingsingo

dingsingo

I think the best is: - 1,25GB singelmode 1310nm 10km and a longhole version - 1,25GB singelmode 1550nm 10km and a longhole version - 1,25GB multimode 550m - 100M singlemode 1310nm - 100M multimode 2km 850nm - 1,25GB WDM 1310/1550nm 10km It's, the TP-Link oder Dlink portfolie by SFP's, too. dingsingo

dingsingo

Gread,

same in one of my Location.

TP-Link SM-Converter with original 5V Powersupply. RB/493AH.

IMG00539-20120210-1204_1.JPG

IMG00538-20120210-1204_1.JPG

dingsingo

dingsingo

the Answere is simple, don't buy the Product !

dingsingo

@Chupaka

++1

THx's

dingsingo

Hi,

my dude 4.beta3 on an WinXP works 8 month without any Problem. Now the Dude didn't send Email when an Device goes down.

I testet an new 4.beta3 dude on the same PC and it works fine. When I import the Backupfile it didn't works.

enybody a Idea ??

Thx

dingsingo

dingsingo

@honzam

can you give up a photo of the Ethernetport ? Is it a better handlink as SXT ?

Thx
Dingsingo

dingsingo

Hy,

is it corrctly that the new RB100AH have no fans by dafault ? The old Version of 2010 have two of them intern ?

Thx

dingsingo

dingsingo

Hi, look http://www.meanwelldirect.co.uk/product/AD-55A/AD-55A/default.htm and a RB/433AH, RB/411AH, RB/435G or someting. Then you can make an Dude-Trape to "heath" and the Powerinput on the Routerboard. If the AC input form Meanwell is down, the DC output goes 1,5volt down. The dude can s...

dingsingo

would you please tell me which case your 435G is in? or just outdoor case? I am looking for good indoor case for 435G.
thanks.
Code: Select all
system health print
show anything to you?

Hi,

no Power Info. Only Fan-Status by 'system heath print'

dingsingo

dingsingo

Hi,

I've to of the new RB/435G and it ist a fine Produkt. But the Powermonitoring dosen't works.

Same in Wonbox or via SNMP. No Date and no OID-Trape....

435G-Health.JPG

Dingsingo

dingsingo

Anybody check if stability of 802.11n wireless is better?

Hi, it works very fine. Better than 5.beta5...

dingsingo

dingsingo

5.0rc1 in normal Wlan 802.11n Link with MPLS/VPLS Backbone without Firewall, QoS or so works very good. Same with two R52 on RB/600 in 2km Link. Stabil Link with low Latence by >20Mbit traffic.

dingsingo

dingsingo

one of my Project. 5Ghz on a old Oeltower, 27m high. It stay in the middel of a small City as a museum. förderturm_IMG_1431.JPG 24 Volt "Mean Well Powersupply" with Accu, on the Towerground. 19072010174.jpg Cases with RB/433AH, a 23dB 5Ghz Antenna to Backbone. Two 90 Grad sEctor for connec...

dingsingo

If they do, a product similar to this http://www.rfelements.com/StationBox-5GHz-12dBi-MiMo-antenna.html would be decent starting point. First affordable dual polarity enclosure I have seen, but 12 dBi is far too low. Thanks for sharing. Look hear: http://www.poynting.co.za/ECGWebManager/MainContent...

dingsingo

Hi, at any rate, it give this new Products: RB711-5Hn-M - RouterBOARD 711 with 400Mhz Atheros CPU, 32MB RAM, 1 LAN, 1 built-in 5Ghz 802.11a/n card, RouterOS L3, MMCX connector RB711-5Hn-U - RouterBOARD 711 with 400Mhz Atheros CPU, 32MB RAM, 1 LAN, 1 built-in 5Ghz 802.11a/n card, RouterOS L3, U.fl co...

dingsingo

Hi, we use Mean Well Buffer Power Supply AD-55B 24V 2A Link: http://www.meanwelldirect.co.uk/product/AD-55B/AD-55B/default.htm 2x 12V 7,2Ah Accu. A Relais on 230V side, go the AC down the Relais fall, too. The Contact from Relais bridge Pin 2 and 3 on a free ethernetport at the Routerboard. So we se...

dingsingo

What band settings you use? I just test it on 411 with 4.6 RouterOS in indoor setup each chain conform chain settings. When you set RX/TX =0 J4 working in both directions. When you set RX/TX = 1 both directions working over J5. Set is only 802.11a with a vertical and a horizontal Antenna. Other Sid...

dingsingo

He ask number over there device name. Antenna mode settings is not active for this wireless card. Each chain have only one antenna output. Use ht-rx/tx chain= to configure antenna-mode. Hi, it not so simple. When we use V4.5 or V4.6 with 1 Antenne on J4 and setting HT-rx / HT-tx = 0 ist dosn't work...

dingsingo

Hi,

is this Problem fixt ? I've testet R4.6 with R52Hn. Other side is R5H R4.6.

20Mhz by 802.11a works fine by ~30dB signal. When we goes to 10Mhz Channel, the Link didn't work.

Dingsingo

dingsingo

Hi,

I've add via Web-portal a with profile named: 2M/384kb ( limit ist 2M/384kb).

When I look via termial, I see:

/tool user-manager user
add comment="" customer=admin disabled=no name=11111 password=22222 shared-users=1

Where is here the profile ???

thx

dingsingo

dingsingo

It works perfectly without fan. We tested it with a heatsink for more than 24 hours at full load. The temp was higher, but it worked no problem. So if you want, you can replace the fan with some kind of heatsing (the bigger the better).

Hi normis,

ok this are good news.

Thx

dingsingo

dingsingo

My feeling, too.

is the fan watch by snmp ? So i can see, the fan is dead.

dingsingo

dingsingo

@csickles i'am interess, form print simple Ticket via a POS IP-Printer. When you must have some Money for this, i thing is not an Problem. A Serialnumber and so is not so inportants My Dream is the sam Funktion of the Handlink WSG-5000. Finally the Important Point is, ist must work in my System :-) ...

dingsingo

hi,

how set the N-Testlink to max. 36mbps-HT or 56,5Mbps-HT on the connection ??

Thx

dingsingo

dingsingo

5Ghz or 2,4Ghz ???

dingsingo

Hi, I've a Link over 8km. A-Side: Rb/411AH (Ros 4.5) R52Hn 2meter Coaxcable 1x 23dB vertical 1x 23dB horizontal B-Side: RB/600 (Ros 4.5) R52Hn 2meter Cable 1x 23dB vertical 1x 23dB horizontal Link goes with 43dB Signal and by HT20-8 B-Test ( udp 1500) say max. 30Mbit half and 8Mbit by duplex. Thx di...

dingsingo

Hi,

something news about this topic ? i didn't when the UPS goes to Backup, too. Via RS232 on the RB.

dingsingo

dingsingo

Hi,

we have update 6 RB/600 with MPLS/VPLS an OSPF. System works fine...

dingsingo

dingsingo

Hi, very fine... MPC8544 800MHz Memory 256MB DDR SDRAM onboard memory Boot loader RouterBOOT Data storage NAND memory chip, CF slot on back Ethernet Three 10/100/1000 Mbit/s Ethernet ports with Auto-MDI/X miniPCI 4 x miniPCI, 1 x miniPCI-e Expansion regular PCI daughterboard port, PCI-e daughterboar...

dingsingo

Hi,

have you the dude-script to watch the Info's from the UPS-Paket in the RB ?

Thx

dingsingo

dingsingo

I am secretly hoping that '1' stands for a SFP/miniGBIC port upgrade for the RB600... Goodbye lightning (of sorts)

Me too, I could really use at least one SFP slot for some fiber installs.

Hi,

a RB433AH/SFP with two gigabit Ethernet and one GBIC-Port for SFP.

Thx

dingsingo

dingsingo

Hi,

we looks like for a Mainboard that have a SFP-Port.

Anyone an idea what I can take it?

dingsingo

dingsingo

helo to all mikrotik expert

does mikrotik supports ubiquiti Nanostation?

thanks

Hi,

NS2 and NS5 works very fine on Mikrotik Accesspoints.

dingsingo

dingsingo

Hi we are a large WISP that started using Mikrotik as a faster backhaul to replace our Trango T45's. We are using XR2's in the 5Ghz TURBO and Nstream. As my understanding, the only way to create a wireless bridge is to mess with all the WDS stuff. Is this the best and fastest way? We need MAXIMUM s...

dingsingo

Probably it shows as invalid in bridge ports, because LDP is not running, check /mpls ldp neighbor print Hi, I've the same Problem. The hole System is 3.23 with ~50 Nodes. One new Nodes ist RB433 and 3.25. When we route the VPLS Traffic over the New Node, the VPLS goes up. But no PPPoE-Traffic thro...

dingsingo

we also built a small box that is monitoring input voltage and batt voltage und speaks with the mikrotik-ups-monitor
it also monitors the temperatur and turns a fan on an d off and sends email in case of overtemperature

Hi,

have you more information about this box ?

dingsingo

dingsingo

Hi @fly

we use on both Side Dual-Ponyting 20dB with 20cm Pigtails. SNR ~40dB.

dingsingo

dingsingo

I have 30mbps full duplex with regular 40Mhz channel.
Correction...35mbps not 30.
It's 37Mbps full duplex, for precision... and I'm using 20Mhz.

Hi, have you other 5Ghz Link in the neighborhood ?

dingsingo

dingsingo

Hi, my Testlink broke by more than 10Mbit throuput. The Client say in Log: "lost connection, not polled for too long" dingsingo try disabling the periodical calibration and disable nstreme. Hi, I've disable the parameter. But not realy better. I thing, the Problem is, the we have other 5G...

dingsingo

Hi,

my Testlink broke by more than 10Mbit throuput.

The Client say in Log: "lost connection, not polled for too long"

dingsingo

dingsingo

Hi,

ok it works. But 20Mhz and ~30dB Signal. Max. 35Mbit in one way by H20-8. Two-Way ~2Mbit max. on 8km an other 802.11a in the neighborhood CCQ ~60-80%.

dingsingo

dingsingo

Hi, my Testsystem over 8km will make not more the 54Mbit brutto. Why the System dosn't go to HT-Mode ? RB433 V4.beta3 with ~30dB Signal The Config form AP ist: /interface wireless set 0 ack-timeout=dynamic adaptive-noise-immunity=none allow-sharedkey=no \ antenna-gain=0 antenna-mode=ant-a area="...

dingsingo

Never seen anything better than this (Tested on RB133c3 with R52n and RB411AH with R52n). Bandwith test shows up to 25 - 30 Mbps, not more ...

Hi,

sorry SNR is 7 , not more ???

Thx

dingsingo

dingsingo

Hi,

PPPoE ist Layer 2. A WDS oder AP-Cleint is Layer3. Use an EoIP oder VPLS Tunnel from PPPoE-Server-Interface to the AP (RB400). The User Client as Client-Psudobridge, build an Bridge on it. In the Bridge put the Wlan an ether-Interface.

dingsingo

dingsingo

Hello,

i think the easy Way is. The Dude on an RB an on the Com-Port connect an GSM Modem. The Dude kann send the trap directly to the GSM Interface.

dingsingo

dingsingo

Hi,

itsn't the easy way that Dude send the notification directly over the Com-Port to the GSM-Modem ??

Thx

dingsingo

dingsingo

Hi,

i've make an APC via serial-Kabel on an RB/450. On this work 3.23 with the UPS-Package.

My Qustion is, how i can buildin the Status by USV in the Dude 3.4 ?

An SNMP-Walk on the RB, didn't find an OID from the UPS-Package.

Thx

dingsingo

dingsingo

Hi all, I'm seeing some strange behaviour of OSPF on wireless link's. I have OSPF running on approx 40 router's and there is probaly some bug causing that randomly some wireless interface change state to down, If I check wireless registration table link uptime is in days. There is no message in log...

dingsingo

Hi, I believe that the Routerboard should not always must the are inexpensive. Many WISP not really locking of 10$. But when the Product was not stabil and dosen't work good. The cost for Service beyond in the first Servicemission the 10$ saving. Build Hardware they was work good and stabil for the ...

dingsingo

Hm, I tried to use SNMP for voltage montitoring with rb333, rb433ah, rb1000 with 3.20 and 3.22 fw, but the health oids didn't work... does someone know why??

Hi,

only the RB/333 , RB/433AH have an Volt Monitoring !

dingsingo

dingsingo

yeah, right, and disconnect all clients every 5min, good idea

sorry, i mean. That only when CCQ under ~50%, than rescan the Interface.

dingsingo

dingsingo

Hi,

or you need a script, that scan the Chanel every 5 min. for CCQ an signal. Is the CCQ to low, the Board rescan the Link.

dingsingo

dingsingo

Do you mean with "bridge between RB's" that router B in your setup is bridge (not MPLS switching router)? Please post for _all_ involved routers output of: /ip address print /ip route print /mpls ldp interface print /mpls ldp neighbor print /mpls local-binding print /mpls remote-binding p...

dingsingo

what is the output of: /tool traceroute 172.20.5.100 src-address=172.17.100.1 when run on 172.17.100.1? and /tool traceroute 172.17.100.1 src-address=172.20.5.100 when run on 172.20.5.100 Do you get IP connectivity over VPLS tunnel when you configure IP address for the bridges that VPLS tunnels are...

dingsingo

dingsingo, describe your network diagram and exact configuration - the information you provided is not enough to diagnose the problem. - Are you using LDP? - Are labels properly distributed for routes? - Is there MPLS end-to-end connectivity between VPLS tunnel endpoints? - Assuming you use static ...

dingsingo

Hi,

it is funny. between to RB600 with MTU 1600 over Lan is VLPS-Link running.

But RB600 over Wireless with MTU 1600 the VPLS-Link don't work. Why ????

dingsingo

Hello,

in 3.22 it is the same Probleme.

dingsingo

dingsingo

Hi,

in 3.21 is *) added WinBox MPLS & VPLS support mpls-test package.

But i didn't see in Winbox with Version 3.22. It's again out in 3.22 ?

dingsingo

dingsingo

Hi,

it is funny. between to RB600 with MTU 1600 over Lan is VLPS-Link running.

But RB600 over Wireless with MTU 1600 the VPLS-Link don't work. Why ????

dingsingo

dingsingo

What is the RB616 mentioned in the 3.22 release notes ?

and what ist RB 616 ?????

dingsingo

MTU issue?

Hi,

the Backbone ist on MTU 1600, MPLS Interfaces on default (1508), PPPoE-Server 1492.

dingsingo

dingsingo

Hi, we have in the internal Network an OSPF and EoIP based Backbone. Now we will switching to MPLS with VPLS-Tunnel for transport the PPPoE-User to the Accesscontroller. We use 3.17 and 3.20 with newest routing-test and mpls-test packet. Problem is, the VPLS Tunnel ist up and bild in the Bridge incl...

dingsingo

hi, i've test the 3.19 with routing-test and mpls-test, for use MPLS incl. VPLS and disable the EoIP-Tunnels in the network. The system have problem in the ospf-routing and it was very unstable. I downgrade the ~50 MT's after 4 hour to 3.17 with routing-package without mpls-test an MPLS/VPLS. ...hop...

dingsingo

Hello,

have anybody an script for me that change the 5Ghz Channel, when the CCQ under ~50%?

Thx

dingsingo

dingsingo

Is there any oid for voltage? On rb333 works fine but on 433ah I can't find the oid :/

iso.org.dod.internet.private.enterprises.mikrotik.mikrotikExperimentalModule.mtXRouterOs.mtxrHealth.8.0

dingsingo

dingsingo

dingsingo

Hi,

RB44GV oder RB44G can work with more than MTu 1500 in MT Verson 3.x ??

Thx

dingsingo

dingsingo

it one of them.

Which card supports Jumbo Frame under Mikrotik V3.x and it's Gigabit ?

dingsingo

dingsingo

Hi,

i've a x86 Board with V 3.6 and a Intel PRO/1000 Card. The MTU of the Card dosn't got bigger than MTU 1500. Intel read Jumbo Frame works.

Anybody have an Idear ?

dingsingo

dingsingo

we built a battery monitoring module an scripts for it and in addition with powersupply you have your low cost ups talking to mikrotik... http://www.stone-rich.at/dl/str-ups/default.htm regards Hi, ich hätte da auch mein Frage zu. Knasst Du mir mal eine Mail schicken? technik[at]FNOH.de dingsingo

dingsingo

Something simlar to this / system script add name="log_rf_data" source="#/int wir reg print \n:log debug \( \ \"log_rf_data::signal-to-noise=\" . \[int wir reg get \[find \ interface=wlan1\] signal-to-noise\] . \",tx-ccq=\" . \[int wir reg get \ \[find interface=w...

dingsingo

Try this.
/ system scheduler add name="Reboot Router Daily" on-event="/system reboot" start-date=jan/01/1970 start-time=00:10:00 interval=1d comment="" disabled=no

Hi,

it work's in RC3.0, too??

Thanks

Dingsingo

dingsingo

36-12db = 24 would make it senseless. The only solution is to fulfill the requirements of EN302502. And only the equipment which does this is usable/sellable. Stefan the regulation is only for WISP (commercially uses ) not for private use Yes. I'm a WISP. I want to use it :o . Stefan Me too..... di...

dingsingo

Hi,

I try despair the profiles in userman to adjust. Unfortunately do I find the Profil in Userman?

Can anybody help??

Dingsingo

dingsingo

it looks like everything is fine in 2.9.34...

But it looks in such a way, as if it would really go into 2.9.34.

dingsingo

The private ip is not an issue. Did you bind the static public to the incoming interface of the Mikrtoik though?

Hi Stryker777,

Thus if you want to know whether I the Public IP on the Uplink of the MT registered? Yes I do. Crasy is, in the 2.8 goes in the 2.9 does works.

Dingsingo

dingsingo

Hi,

same in 2.9.34

is the int. 10.10.10.10 the Problem? The Program connect on Port 443 an work over Port 3299.

dingsingo

dingsingo

You are right. I used up myself. Is changed already above. But everything unfortunately goes except this software.

In the 2.8.xx stands only nat in the 2.9.xx src nat & dst nat in it. Into 2.8 it goes, also only into 2.9 stop this SAP-Program.

Dingsingo

dingsingo

Hi, I have the following problem with the use of a SAP program. The customer goes over PPPoE on the MT (2.9.33) and receives 10.10.10.10/32 thus IP. This is converted in the NAT on the 138.xxx.yyy.zzz/32. Thus the customer is arriving and going off over the Pubilc-IP 136.xxx.yyy.zzz attainable. Over...

dingsingo

Hi, I have two Uplinks with the IP XXX, YYY. The user pubilc IP's assigned by PPPoE on the server in a IP from the pool 2x /24 selects itself and gets. Depending upon whether it is one from the block 1 or 2 becomes the packages lack and over Uplink 1-2 sent. Unfortunately do not ring that 100%. Can ...

dingsingo

Hi,

2Ghz and 256Mb are too little for 350 PPPoE Client. Because if not all online are runs there with 2.9.30 completely well. But with the 2.9.31 or also 2.9.32 that cannot be done in the long term.

dingsingo

dingsingo

Hi,

If the Client is disconnectet can these more not again itself logging in. The entire PPPOE-Server nearly stands still. Are 2.9.30 ist work an it will be better

dingsingo

dingsingo

You do not need script, time matcher is implemented in 'ip firewall mangle'. Enable 'time' for packet-mark rules, it will enable mangle for the configured time. Queue tree will stop work after mangle will not match correct time. Note, time is added to simple queues too. Sorry, I don't have said it ...

dingsingo

Hi,

I look for script a that Queue-Tree in the morning switch on and evening off switch. Someone has an idea ??

Thx

dingsingo

Ok,

.. http://www.mikrotik.com/docs/ros/2.8/ap ... g1.content

THx

dingsingo

Hi,

I look for script a that Queue-Tree in the morning switch on and evening off switch. Someone has an idea ??

Thx

dingsingo

dingsingo

Hi,

I look for a Script, with which I can every 24 hours again start the PPPoe-Server. Does someone have an idea?

dingsingo

dingsingo

Would anyone out ther know what the default ARP age timeout is on the Mikrotik ethernet interfaces? The default on Cisco routers is 4hrs...can't seem to find anything on the Mikrotik routeros. Running 2.9.30. THANKS! :wink: Me, too !!! I will PPPoE-client out-logs itself is with again to login anot...

dingsingo

hi all

I am having a problem connecting a Mikrotik to a PPPOE connection
It dials but will not redial if disconnected

Any ideas

regards

malcolm

Hi,

set "Dial on Demand" in the Client settings of on.

dingsingo

dingsingo

in addition to adding the src/dst nat rules you have to add the public IP you're mapping to the WAN interface on the router. You mean so? dst-nat: 1 X src-address=10.100.x.xx/32 action=masquerade to-src-address=216.2xx.xx.xx and src-nat: 1 X src-address=10.100.xx.xx/32 action=redirect to-dst-addres...

dingsingo

Hello,

someone can say to tell me, to route a public IP to an internal Client IP ?

when I write in src-nat and dst-nat it is not work. Is the pransparent Web-Porxy the Probleme?

FW is 2.8.28

thx

dingsingo

dingsingo

Hi,

ok, i changes form 2MB to 6MB, think thats good form ~100 Client.

thx

dingsingo

dingsingo

Hi, in our Network the User connect the MT over PPPoE-Hotspots. The Accesspoint have an Filter and blocks all Protocols except PPPoE. For the User we works with WET11 by Linksys. But the WET11 are to get with difficulty. Have enybody an Idea for other Birdgeclient work? WET54V2 doen't work with PPPo...

dingsingo

Hi,

how much DNS-Cache is ok, 2MB 4MB 10MB?? I have an MT 2.8.28 with 256MB RAM and 2Mhz Celeron.

Thx

dingsingo

dingsingo

Hi, I've the same Problem, too. On the internal interface is the PPPoE-Server for User login. The interface 2 ist Uplink one and the interface 3 ist Uplink two. It gibe two DHCP-pools in der MT and the User become an IP for Pool one oder two. This IP is important for the Routing in Uplink one oder t...

dingsingo

Hallo, ich suche nach Möglichkeit deutschsprachige Hilfe für den Bereich Policy routing. Da ich zwei interne IP-Bereich auf je einen der beiden externen Uplink routen möchte. Die Anleitung hat zwar schon geholfen, aber scheinbar gibt es im Zusammenhang mit den transparet Web-Proxy Schwierigkeiten. A...

Search found 116 matches