MikroTik

MulderSk

The quesion is for Mikrotik engineer The MikroTik runs on Lenovo System x3550 M5 hardware with 28-Core 2.30 GHz 2x 14-Core E5-2695 v3 processors. Why is the CPU frequency so high when the CPU load is low? At 0 percent load, the frequency is around 1600 MHz, and at 5 percent load, the CPU frequency i...

MulderSk

After upgrade ros to 7.6 on CRS305 cpu increased from 1 to 2 cpu wtf ?

MulderSk

Today I bought AF-60-LR I was waiting 2 years that Mikrotik made something like this for more then 2 km distance. I wrote several mails to mikrotik teams to build something like AF60LR for more distance and answer ? We have LHG60 ,but more ISP need something for 4 - 6 km . When UBNT can build that W...

MulderSk

picture from dude nRAY60 poor link

MulderSk

Yesterday I start testing nRAY 60 on my PTP link LHG60 - LHG60 1990m at the moment I remove only one side with nRAY. RSSI on lhg60 LHG60 was -58 now with nRAY RSSI -54 Rate 2,3 Gbit . Today I noticed that throughput drop to 240Mbit. Rate was stil 2,3 Gbit I start BT on this link and I measured only ...

MulderSk

I tested any other firmware from newest 6.46.6 and now Cube60 on the firmware 6.45.7 4hrs BT without link down link up. Hercules30a try this firmware

MulderSk

I tested link without traffic about 24h all ok no more disconnect link down link up 24h stable then I start traffic link down link up again. Disabling traffic and link again ok without disconnect. Starting BT both direction link disconnecting problem again. On the table I test another 2 units Cube60...

MulderSk

same problem PtMP cube60 to wAP60 360m rssi 63dB link down - link up second PTP cube60 to cube60 520m rssi 57dB link down link up try any firmware link unstable disconnect

MulderSk

Frequency is clear when I scan I try other channels same result

MulderSk

Hi Does any know where may be problem ? Link LGH 60G SXT sq Lite 60 link often down and up I try anything nothing help last I set tx sector=36 .From support says bed alignment antenas but RSSI is 61dB on distance 600m I think its good signal 80 MCS 8 thanks for help

MulderSk

Please what type of PCI is this AOC CGP i2 ? disapproved to my pciex4 port on pc board. It is possible any adapter ? thanks

MulderSk

Link 3,8 km work very good I wait on rain

backup on 5Ghz

MulderSk

Thats a long way for the LHG60's!

On 6.43rc32 Link works 2 months without problem only heavy rain link go to backup on 5Ghz few minutes distance is no problem

MulderSk

Link 2362m LHG60 After upgrade form 6.43rc32 to rc51 link very unstable Signal drop to 20 from 80 ,ping from 2ms to 500ms very low throughput back to rc32 all ok link stable signal 80 mcs8 ping 2ms

MulderSk

MulderSk are you using a couple of "normal" LHG60?

yes

MulderSk

right now rain , normal rain has no effect only very very hard rain was link down 2min

MulderSk

Now rain and one side not adjust work ok

MulderSk

Look on picture Terminal distance 1993m I mean real distace, not from integral MT monitor. I don't trust mikrotik internal range meter, it can say about 3 km when actually link about 120 meters. I measured this link on google earth 1970m other link on wAP60G show 236m google earth show 240m Mikroti...

MulderSk

Did you mean exactly 2.000 meters or 1900 meters or 2100 meters? Becuse in 60G every few meters are important.

Look on picture Terminal distance 1993m

MulderSk

BT TCP from CCR 1016

MulderSk

Where I can download winbox 3.14 rc ? thanks

MulderSk

it fits jrc24 extreme nicely. Too bad I have a lot of non extreme versions. I tested that today... 185m one side is aimed to best signal, other site I just put there and hoped. signal 80... cable speed.... Thanks for the tip MulderSK ! here https://webshare.cz/group/Cj27iJn2in/ wAP60G in parabola M...

MulderSk

do you have pictures of JRC assembly? I have a lot of spare JRCs...

JRC 24 https://webshare.cz/group/61E6u94rll/

JRC 29 https://webshare.cz/group/3N21hM40my/

MulderSk

Is it stable with rain? We have a link test 487m with similar solutions with 80 signal but we lost link with rain. Rain is no problem link ok signal from 80 drop to 60 MSC from 8 to 6 but yesterday snow , one PTP wAP60G - JRC29 with wAP60G 320m heavy snow signal 80 no problem only when water snow o...

MulderSk

480m one side wAP60 inside LHG XL second side wAP60 inside JRC24 signal 75 MCS 8 sometimes 6
https://webshare.cz/#/group/33u784To2K/

MulderSk

obviously its possible to replace wap60 board into lhg box relatively easy. Still I am convinced that the lhg mesh reflector isnt best solution for 60ghz wavelenght. i will repeat it again. Probably would be the best to replace somehow wap60 board inside ldf box and then mount ldf60 on any appropri...

MulderSk

320m signal 80 MCS 8 full speed but one side wAP is inserted into LHG XL Please can you post some pics about this hack? Thank you first I tested about 1 month when wAP 60 in LHG only with tape but today I recieved another units so I make new version :-) foto https://ulozto.sk/tam/_PQHTNYRtxU2w seco...

MulderSk

320m signal 80 MCS 8 full speed but one side wAP is inserted into LHG XL

MulderSk

What is the default password please ? because I cant connect through winbox on mac address admin blank don't work thanks

MulderSk

Good results! Was this with traffic? Photo does not show any. Try it with full load. Hi Normis why is not possible connect to mUPS through winbox to ros and manage mUPS ? use monitoring , watchdog and other.How can I monitoring problem with power now ? thanks for answer. In brochure you wrote In Ro...

MulderSk

Hi, mUPS sounds interesting. Is it possible to power possibly a PowerBox at which probably 4 wireless systems are connected wit PoE? So is it possible to power 5 routerboards at the same time with one mUPS? Or is the current output limited anyway? 2A current (at 24V) should be ok for this constella...

MulderSk

Hi after overshoot power in I lost menu POE in routerboard now Icant power other device. I make netinstall and still poe is missing in interface menu any help ? thanks

MulderSk

I Have A Problem With the signal SSID
the signal is hidden and It shows in broadcast

same problem SXT G-5HPnD r2 ros 6.35

MulderSk

save backup to version 4.03 file with backup.tgz and then import this file to version 6.34 backup.xml I had same problem now work fine

MulderSk

I have a query in version 3.6 could do backup of my settings and networks; and in version 6.34 does not show the option to backup or export .. It's now a command line task on the DUDE Server - http://wiki.mikrotik.com/wiki/Manual:The_Dude_v6/DB_import_export /dude export-db file=(file_name_path) .....

MulderSk

I have tried that but with .xml file and it doesnt work

same problem any idea ?

MulderSk

Can you describe it ? I have point to point AP bridge other side station bridge you change the mode to WDS ? and only routing on interface ? I have several link in NV2 multihop and problem tcp single thanks

MulderSk

I was also going to ask same question , Why do you need the old legacy nstream over NV2? TCP over multiple hops performed much better at times nstreme was working. nv2 has better link performance but single users do not get the tcp performance with speed tests as they did with nstreme. Newer nv2 is...

MulderSk

I was also going to ask same question , Why do you need the old legacy nstream over NV2? maybe in NV2 1 TCP connection is low throughput when AP bride mode is use with routing NV2 is ok ,but in Nstreme mode when AP or CPE is in bridge mode 1 TCP connection is throughput ok more hops too sorry for m...

MulderSk

It seems that after changing ethernet cable to new Cat7 Shielded with shielded module, port flapping vanished

Hi I have same problem on several mikrotik You try cat6 ? or only cat7 solved problem ? thanks

Search found 40 matches