Community discussions

MikroTik App

Search found 27 matches

by migo
Wed Jan 06, 2010 2:18 pm
Forum: General
Topic: RB750 Port Based VLAN
Replies: 19
Views: 16784

Re: RB750 Port Based VLAN

migo, you have to remove/clear the SLAVE (Master Port) options from the Ether3-5 interfaces. Pada, look for my first post in this topic. [admin@MikroTik] /interface ethernet> print Flags: X - disabled, R - running, S - slave # NAME MTU MAC-ADDRESS ARP MASTER-PORT SWITCH 0 R ether1-gateway 1500 00:0...
by migo
Mon Jan 04, 2010 9:44 pm
Forum: General
Topic: RB750 Port Based VLAN
Replies: 19
Views: 16784

Re: RB750 Port Based VLAN

see above?..
Could you export sample config? That isn't work on my RB750.
by migo
Mon Jan 04, 2010 4:27 pm
Forum: General
Topic: RB750 Port Based VLAN
Replies: 19
Views: 16784

Re: RB750 Port Based VLAN

Any suggestions how to set up port based vlan on mikrotik 3.x on rb750?
switch mode is disabled.
by migo
Wed Dec 30, 2009 4:36 pm
Forum: General
Topic: RB750 Port Based VLAN
Replies: 19
Views: 16784

Re: RB750 Port Based VLAN

because at that moment I used only ether1 (ether2,3,4,5 was unplugged)
by migo
Wed Dec 30, 2009 3:31 pm
Forum: General
Topic: RB750 Port Based VLAN
Replies: 19
Views: 16784

Re: RB750 Port Based VLAN

Hello, Im trying to setup port based vlan on RB750 Its my config: (doesnt work) I dont have any filter rules. [admin@MikroTik] /interface ethernet> print Flags: X - disabled, R - running, S - slave # NAME MTU MAC-ADDRESS ARP MASTER-PORT SWITCH 0 R ether1-gateway 1500 00:0C:42:56:E4:6D enabled 1 ethe...
by migo
Thu Sep 18, 2008 4:56 pm
Forum: Wireless Networking
Topic: bonding on miltiple wireless links, need help
Replies: 1
Views: 1131

bonding on miltiple wireless links, need help

Hello, I want to configure bonding for 4 wireless links on two computers: [eth](computer a) [wlan0]===[wlan0] [eth](computer a) bonding1(wlan0,wlan1,wlan2) [wlan1]===[wlan1] bonding1(wlan0,wlan1,wlan2) [wlan2]===[wlan2] Problem is that wifi cards (wlan1,wlan2) disconnects after create bonding. Below...
by migo
Sun Feb 03, 2008 6:11 pm
Forum: Wireless Networking
Topic: [ROS 3.0] ht-channel-width etc... no questions?
Replies: 1
Views: 925

[ROS 3.0] ht-channel-width etc... no questions?

Hello, Since 3.0 some beta mikrotik version in /interface wireless nstreme-dual has had options without discription. I can't find any informations about this options: ht-rates=1,2,3,4,5,6,7,8 ht-guard-interval=long ht-channel-width=20mhz ht-streams=single Could somebody explain me what is ht-rates e...
by migo
Tue Oct 30, 2007 4:53 pm
Forum: General
Topic: RC9 - bridge in nstreme2 dosn't work
Replies: 12
Views: 2788

Re: RC9 - bridge in nstreme2 dosn't work

I confirm that after reset to default settings and reconfigure both rb333 again transparent bridge works correctly:)


Thanks janisk.

BTW. Strange but ip addresses added to brigde ether interfaces doesn't work but machines before and after bridge are visible.
by migo
Tue Oct 30, 2007 3:17 pm
Forum: General
Topic: RC9 - bridge in nstreme2 dosn't work
Replies: 12
Views: 2788

Re: RC9 - bridge in nstreme2 dosn't work

Try put IP address on Bridge interface instead. It doesn't work too. I'll precise my configuration: 192.168.1.121-[ether1-point-A] ====(nstreme2)====[point-B-ether1]-192.168.1.120 I want to create bridge, transparent connection. configuration on Point-A: [admin@point-A] > ip address print Flags: X ...
by migo
Tue Oct 30, 2007 11:18 am
Forum: General
Topic: RC9 - bridge in nstreme2 dosn't work
Replies: 12
Views: 2788

RC9 - bridge in nstreme2 dosn't work

Hello, I can't run bridge on working connection nstreme-dual. Nstreme2 is working: --- [admin@MikroTik] /interface wireless nstreme-dual> monitor 0 rx-signal-strength: -60dBm tx-signal-strength: -65dBm rx-rate: "48Mbps" tx-rate: "54Mbps" connected: yes (..) --- Bridge is working for ether1 and nstre...
by migo
Tue Dec 12, 2006 10:30 pm
Forum: Wireless Networking
Topic: 5.1-5.8 GHz antenna for snowstorms
Replies: 5
Views: 1385

The loss could be one of two things - you need to identify which it is: 1: Fade due to snow in the path (i.e. all the snow between the antennas) 2: Fade due to snow and ice ON the antenna You're right. I'm using parabolic antennas. It was snow ON the reflectors (~5cm). You may want to look into the...
by migo
Tue Dec 12, 2006 11:25 am
Forum: Wireless Networking
Topic: 5.1-5.8 GHz antenna for snowstorms
Replies: 5
Views: 1385

5.1-5.8 GHz antenna for snowstorms

Hello.

I need 5.1-5.8 GHz antenna for log (~15km) distances on dificult area with snowstorms (on my parabolic antennas durring snowstorm I lost -30dBm signal on link).

Is any sugestion?
by migo
Tue Dec 12, 2006 10:40 am
Forum: Wireless Networking
Topic: URGENT! Mikrotik lost wds connection and can't reconnect.
Replies: 1
Views: 993

URGENT! Mikrotik lost wds connection and can't reconnect.

Hello, I have problem with mikrotik (tested the newest 2.6.38). Mikrotik lost connection in peer-to-peer wds link: lan --RB532 A(station-wds + nstreme)------(bridge + nstreme)RB532 B---lan .. and can't stable connect again (watchdog is running and restarting both rb532). In log RB532 A i have (i can...
by migo
Wed Nov 29, 2006 10:41 pm
Forum: General
Topic: pppoe server question
Replies: 0
Views: 640

pppoe server question

hello,

Did Mikrotik write new pppoe server?
If not..
Is it modified GPL licensed software (for example rp-pppoe)?

I'm asking because it's dificult to find good pppoe server for linux os.

Regards,
Tom
by migo
Mon Jul 31, 2006 9:12 pm
Forum: Wireless Networking
Topic: can't turn on turbo on interface-type=Atheros AR5213
Replies: 18
Views: 3709

off course all community igore my question
by migo
Fri Jul 28, 2006 12:19 pm
Forum: Wireless Networking
Topic: can't turn on turbo on interface-type=Atheros AR5213
Replies: 18
Views: 3709

It's strange, no one from forum knows what cards support turbo mode and why in that strenght of signal i have not stable link of nstreme2?
by migo
Thu Jul 27, 2006 9:39 pm
Forum: Wireless Networking
Topic: can't turn on turbo on interface-type=Atheros AR5213
Replies: 18
Views: 3709

so what cards have ability to enable turbo mode with mikrotik, on atheros web page i seen that this card have turbo mode. in /system package i disabled wireless and enabled wireless-legacy but after reboot in /interfaces mikrotik didn't detect any atheros cards on legacy driver. so i don't know what...
by migo
Thu Jul 27, 2006 7:15 pm
Forum: Wireless Networking
Topic: can't turn on turbo on interface-type=Atheros AR5213
Replies: 18
Views: 3709

can't turn on turbo on interface-type=Atheros AR5213

hello, [topic copyed from routerboard forum] I have two PC stations (P4 2,4GHz) with mikrotik 2.9.27. This is config one station: interface wireless> print interface-type=Atheros AR5213 mode=nstreme-dual-slave frequency-mode=superchannel antenna-gain=0 tx-power-mode=default compression=no allow-shar...
by migo
Wed Jul 26, 2006 9:43 pm
Forum: RouterBOARD hardware
Topic: low performance of nstreme2?
Replies: 0
Views: 1114

low performance of nstreme2?

hello, I have two PC stations (P4 2,4GHz) with mikrotik 2.9.27. This is config one station: interface wireless> print interface-type=Atheros AR5213 mode=nstreme-dual-slave frequency-mode=superchannel antenna-gain=0 tx-power-mode=default compression=no allow-sharedkey=no (...) interface wireless nstr...
by migo
Tue Jun 20, 2006 10:34 am
Forum: General
Topic: motherboard cpu temperature
Replies: 17
Views: 7642

now i don't remember. i'll check it. but in lm_sensors is sensors-detect program. mayby good option will be option for example /system health sensors-detect and /system health print showing all detected values?
it's little dangerous when i can't monitor temperature in some locations where is very hot.
by migo
Tue Jun 20, 2006 9:51 am
Forum: General
Topic: motherboard cpu temperature
Replies: 17
Views: 7642

so.. why MT can't use lm_sensors to check temperature of cpu?
Is any chance to fix it in near future? It's urgent.
by migo
Tue Jun 13, 2006 11:50 am
Forum: Wireless Networking
Topic: New MT 2.9.12 and 5ghz-turbo
Replies: 4
Views: 1558

I have this rpoblem too. MikroTik v2.9.23. Anybody knwo what is with 5ghz-turbo now?
by migo
Thu Apr 20, 2006 2:10 pm
Forum: General
Topic: bridged EoIP doesn't work
Replies: 3
Views: 1035

I had 2.9.10 and that configuration didn't work.
by migo
Thu Apr 20, 2006 12:09 pm
Forum: General
Topic: bridged EoIP doesn't work
Replies: 3
Views: 1035

after upgrade to 2.9.20 tunnel and bridge works fine
by migo
Thu Apr 20, 2006 11:40 am
Forum: General
Topic: bridged EoIP doesn't work
Replies: 3
Views: 1035

bridged EoIP doesn't work

Hello, I have 2 networks conneted by rb's with mikrotik. First: --------- [admin@first] > /interface eoip print Flags: X - disabled, R - running 0 R name="tunel_1" mtu=1500 mac-address=FE:97:8F:93:AA:EC arp=enabled remote-address=192.168.3.2 tunnel-id=1 I have 2 bridge: lan and wan [admin@first] > /...
by migo
Wed Sep 07, 2005 7:57 pm
Forum: General
Topic: 2.9: problem, lost connection after 5 minutes on rb500
Replies: 3
Views: 1251

what have i set to generate all need logs?
by migo
Wed Sep 07, 2005 2:51 pm
Forum: General
Topic: 2.9: problem, lost connection after 5 minutes on rb500
Replies: 3
Views: 1251

2.9: problem, lost connection after 5 minutes on rb500

Since 2.9rc10 on rb500: after 5 minutes work disconnect. Aftrer reboot works fine but only 2-5 minutes. tested versions 2.9rc10 2.9 and 2.9.1. on 2.9rc9 works fine. two rb500 configured to nstreme2 with cards atheros 5213 without compression. standard config with nstreme (5ghz non turbo) with bridge...