Community discussions

MUM Europe 2020

Search found 22 matches

by sindutzz
Tue Mar 30, 2010 7:36 am
Forum: Wireless Networking
Topic: [ASK]Why my RB411AH+R52H can't go further than 23Mbps ?
Replies: 11
Views: 2274

Re: [ASK]Why my RB411AH+R52H can't go further than 23Mbps ?

@popcorrin & colebert

Thank you for your suggestion. I'll to turn down the power once I arrive at my office. BTW, will it make the bandwidth better?
Or 23Mbps is the max for RB411AH without Nstreme and 5Ghz Turbo?

Thank you
Aldhy SP
by sindutzz
Tue Mar 30, 2010 6:17 am
Forum: Wireless Networking
Topic: [ASK]Why my RB411AH+R52H can't go further than 23Mbps ?
Replies: 11
Views: 2274

[ASK]Why my RB411AH+R52H can't go further than 23Mbps ?

Hi, I just setup new link between two buildings using RB411AH + R52H + Flat 20dB Antenna. The distance is 15 meter..yes, only 15 meter. I wish I could pull a cable between the building through the window at 19th floor but it is not allowed. The Topology: PC---RB411AH(AP) - - - RB411AH(station)---FTP...
by sindutzz
Wed Mar 10, 2010 6:07 am
Forum: General
Topic: [ASK] License become Level 0 after Format NAND
Replies: 6
Views: 5021

Re: [ASK] License become Level 0 after Format NAND

You guys right!!

Yesterday I contacted support using my account with attached suppout of my RB1000 with v4.5 installed and replied by them within 24 hours with the license key for v4.5.
And now my RB1000 working normally.

This is great. Mikrotik support is rock!! Good job guys ;)
by sindutzz
Sat Mar 06, 2010 3:42 am
Forum: General
Topic: [ASK] License become Level 0 after Format NAND
Replies: 6
Views: 5021

Re: [ASK] License become Level 0 after Format NAND

NAND format erases license information. you should not do that w/o support request Hi Chupaka, thanks for your reply. Would you please explain to me what do you mean with "support request"? Do I have to contact mikrotik first before I "format NAND"? Actually, before I format NAND, I searched wiki a...
by sindutzz
Fri Mar 05, 2010 6:50 am
Forum: General
Topic: [ASK] License become Level 0 after Format NAND
Replies: 6
Views: 5021

[ASK] License become Level 0 after Format NAND

Hi, I have RB1000 with ROS v3.22 since I bought. Yesterday, I successfully upgraded it to v4.5. What I did was : 1. Upgraded the bootloader 2. Upload the .npk to "File" 3. Restart 4. Update the license key. Everything ran smooth, even the soft ID had updated to 8 digits successfully. But I saw there...
by sindutzz
Mon Feb 08, 2010 10:04 am
Forum: General
Topic: When our MTCNA certificate available for search?
Replies: 23
Views: 3134

Re: When our MTCNA certificate available for search?

Hi Normis,

Thanks for your info.
I'll ask my trainer about this.

Thank you ;)
by sindutzz
Mon Feb 08, 2010 4:06 am
Forum: General
Topic: When our MTCNA certificate available for search?
Replies: 23
Views: 3134

When our MTCNA certificate available for search?

Hi, I Just passed MTCNA Training exam on 29 Jan 2010. I just wonder how long my name will be able to be searched on this link http://www.mikrotik.com/certificate_search.php Will my name automatically listed? Or do I have to wait until I get the certificate and register it at my account? Thank you fo...
by sindutzz
Mon Dec 14, 2009 10:24 am
Forum: General
Topic: What hardware able to deliver 2G pps using mikrotik?
Replies: 3
Views: 969

Re: What hardware able to deliver 2G pps using mikrotik?

I found this on the Cisco web site. Q. What is the maximum packets-per-second (pps) performance of the Cisco NPE-G2? A. Based on 64-byte Ethernet frames, the Cisco NPE-G2 can achieve up to 2 million pps of Cisco Express Forwarding, doubling the performance compared to the Cisco NPE-G1. For more det...
by sindutzz
Sun Dec 13, 2009 7:04 pm
Forum: General
Topic: BGP Configuration
Replies: 7
Views: 4290

Re: BGP Configuration

Thanks George for your prompt response...I am running Mikrotik v3.28 on X-86 Server with RAM-2GB and 4 Processors and 4 NIC cards,so I suppose there wont be any Device level constraints. Will be great if you can provide me with the detailed IBGP configuration of my setup with the below example para...
by sindutzz
Tue Dec 01, 2009 1:30 pm
Forum: General
Topic: What hardware able to deliver 2G pps using mikrotik?
Replies: 3
Views: 969

What hardware able to deliver 2G pps using mikrotik?

I have a client which doing bgp with to my router . At first setup I'm using RB1000 and he use Mr C 7206 with npe400. But when he know that I use RB1000 he ask me if I also have a Mr C device. And yes I have my old unused Mr C 7206VXR with npe 300. And he prefer doing BGP to my Mr C. So I replace th...
by sindutzz
Wed Oct 07, 2009 5:08 am
Forum: General
Topic: How to prevent this loop situation ?
Replies: 3
Views: 919

Re: How to prevent this loop situation ?

Hi fewi,

Yes i already think about that solution too. But the problem, just like you said, this setup will prevent legitimate traffic from heavily utilizing the port. Anyway I'll try it and see what will happen. Thank you for your solution ;)

Aldhy
by sindutzz
Tue Oct 06, 2009 12:50 pm
Forum: General
Topic: How to prevent this loop situation ?
Replies: 3
Views: 919

How to prevent this loop situation ?

http://www.910investment.com/scan.jpg As we can see in the picture, I have a RB450 (Switch1) which act as a switch. At Ether1, I have unmanageable switch (Switch2) connected which located on different floor of my office building. One day, a staff, by a mistake plug a UTP cable on switch2 at port 2 ...
by sindutzz
Thu Sep 10, 2009 9:43 pm
Forum: Wireless Networking
Topic: How to improve wireless ping time with Nstreme enable?
Replies: 10
Views: 2741

Re: How to improve wireless ping time with Nstreme enable?

Hi Tom,

Thank you for your reply :)

I realize that I can not have both advantage. And I choose to enable the Nstreme :D
by sindutzz
Thu Sep 10, 2009 3:29 am
Forum: Wireless Networking
Topic: How to improve wireless ping time with Nstreme enable?
Replies: 10
Views: 2741

How to improve wireless ping time with Nstreme enable?

Hi, Currently,I have a PtP link for distance 10Km at 5Ghz. Both side Using Rb411A+CM9. One as bridge and other as station. Nstreme enable, Enable Polling, disable CSMA, framer policy dynamic size. The signal strength is -69/-70 and TX/RX CCQ around 85-100% and I lock it at 36Mbps. Signal to noise is...
by sindutzz
Thu Jul 23, 2009 9:28 am
Forum: General
Topic: Feature Request : BGP Route Table
Replies: 0
Views: 619

Feature Request : BGP Route Table

Currently I'm working with 3 upstream admins to build a new BGP network. They use Cisco and Juniper to do BGP. And I use a single RB1000 to do peering with them. And they are surprise how I can do filtering for peering very quick using winbox. I still remember their face when I set nexthop out addre...
by sindutzz
Thu Jul 23, 2009 9:13 am
Forum: Forwarding Protocols
Topic: RB1000 BGP having difficulty to advertise to Juniper
Replies: 4
Views: 1770

Re: RB1000 BGP having difficulty to advertise to Juniper

Problem solved, my upstream using local preference above their OSPF network and redistribute their BGP and put their preference to their upstream :( That is why my prefix never choose as the best path since I also advertise my prefix to other upstream. After they filter receiving my prefix from thei...
by sindutzz
Wed Jul 15, 2009 8:59 am
Forum: General
Topic: what is the different between routing and routing-test pack?
Replies: 3
Views: 494

Re: what is the different between routing and routing-test pack?

Thank you normis :)

So on v.3.25, it is better to use routing-test package right?
by sindutzz
Wed Jul 15, 2009 7:48 am
Forum: General
Topic: what is the different between routing and routing-test pack?
Replies: 3
Views: 494

what is the different between routing and routing-test pack?

Hi

I try to find the different between routing and routing-test package.
Already tried to find the thread in this forum but could not found it.

To run BGP on v3.25 or V3.26, which one is better? routing or routing-test package?

Thank you.

Aldhy SP
by sindutzz
Wed Jul 15, 2009 6:26 am
Forum: Forwarding Protocols
Topic: RB1000 BGP having difficulty to advertise to Juniper
Replies: 4
Views: 1770

RB1000 BGP having difficulty to advertise to Juniper

Hi, I'm running EBGP to 3 upstreams using RB1000 2 Upstreams using Cisco 7200VXR 1 Upstream using Juniper M120 I have no difficulty to advertise my prefix to upstreams with Cisco router even when I'm using advance filter. But advertise to Juniper is rather difficult. Sometime, even when my prefix sh...
by sindutzz
Tue Jun 30, 2009 2:02 pm
Forum: General
Topic: "show ip bgp neighbors xxx received-routes" on mikrotik?
Replies: 6
Views: 12966

Re: "show ip bgp neighbors xxx received-routes" on mikrotik?

If you use where and print detail together then detailed information is not printed. We will fix that behavior in future versions. Currently you can use another method /ip route print detail from=[find gateway~"^xx.xx.xx.xx[0x00-0xff]*"] where xx.xx.xx.xx is desired gateway. It works on peer with 6...
by sindutzz
Tue Jun 30, 2009 12:58 pm
Forum: General
Topic: "show ip bgp neighbors xxx received-routes" on mikrotik?
Replies: 6
Views: 12966

Re: "show ip bgp neighbors xxx received-routes" on mikrotik?

As far as I know there isn't alternative for such command. One way you can try is /ip route print were gateway="x.x.x.x" This will work if gateway is the same as peer's IP address. Thank you mrz for your quick reply ;) I already tried that command, and it work :D Yes you are right, it will work onl...
by sindutzz
Tue Jun 30, 2009 11:29 am
Forum: General
Topic: "show ip bgp neighbors xxx received-routes" on mikrotik?
Replies: 6
Views: 12966

"show ip bgp neighbors xxx received-routes" on mikrotik?

Hi,

What command on mikrotik to do "show ip bgp neighbors 114.57.172.50 received-routes" like Cisco ?
Already try to search on this forum, but only got Mikrotik version of "show ... advertised-routes"

Thank you before.

Aldhy