Community discussions

MUM Europe 2020

Search found 24 matches

by usrox
Fri Nov 08, 2013 3:18 am
Forum: General
Topic: PPTP between two Mikrotiks
Replies: 11
Views: 2903

Re: PPTP between two Mikrotiks

Yes, all clients can ping each other.
If you have different subnet on the client side, you must use router for the VPN client and configure the routing on each router so they can connect each of the subnets.
by usrox
Thu Mar 21, 2013 9:45 am
Forum: RouterBOARD hardware
Topic: New - RB951G-2HnD
Replies: 68
Views: 100271

Re: New - RB951G-2HnD

it's not MMCX, I think it is CRC9 connectors like usually used on GSM Modem or cell phones
by usrox
Wed Jan 02, 2013 10:59 am
Forum: General
Topic: Mellanox 10G Ethernet adapter
Replies: 7
Views: 4569

Mellanox 10G Ethernet adapter

Dear Mikrotik Support, Please add the driver on the new releas of RoS for the Mellanox ConnectX®-2 EN 10 Gigabit Ethernet Adapters, or did somebody already try this card on MT RoS ?
by usrox
Thu Dec 20, 2007 7:54 pm
Forum: General
Topic: PPP via serial port on RB133? *Urgent*
Replies: 5
Views: 1181

Re: PPP via serial port on RB133? *Urgent*

By Default Serial Port on Routerboard configured for console, if you want to make the serial port to become normal serial port for dialing modem you can turn off the console service: " /system console disable serial0 " and then you can configure the ppp dial-out (Client) or dial-in (SERVER).
by usrox
Tue Jul 03, 2007 6:23 am
Forum: General
Topic: [Resolved]PPTP vpn configuration[Resolved]
Replies: 6
Views: 1193

Re: PPTP vpn configuration

From my experiece i can't build pptp-server works on bridged interface, if i use non-bridged interface it works just fine. I dont know why :D Maybe my configuration not perfect enough doh.
by usrox
Mon Jun 04, 2007 8:54 am
Forum: General
Topic: PPP via serial port on RB133? *Urgent*
Replies: 5
Views: 1181

Re: PPP via serial port on RB133? *Urgent*

Yes you can use Serial-port for PPP, try disable the system-console.
by usrox
Fri May 11, 2007 7:26 am
Forum: General
Topic: PPTP connections cannot access local subnet
Replies: 7
Views: 3529

From your first rule Try change to-addresses=192.168.111.1-192.168.111.254 with something like to-addresses=192.168.111.1 <-- local ip on your local interface
by usrox
Thu May 10, 2007 6:42 pm
Forum: General
Topic: Hotspot NAT address.
Replies: 7
Views: 1347

Q: are there any default gateway on your hotspot-router (ip-route) ? also check your main router (gateway) are there any NAT rules for your internal-ip (not the hotspot-ip)
by usrox
Wed May 09, 2007 7:36 pm
Forum: RouterBOARD hardware
Topic: NetInstall - No serial cable
Replies: 3
Views: 1352

Hello, if you want to reset your routerboard configuration you can done it by shorting the JP3 (RB100 series) or JP1 (RB500 series).
by usrox
Wed May 09, 2007 6:39 pm
Forum: General
Topic: PPTP between two Mikrotiks
Replies: 11
Views: 2903

Its so simple :

- make pptp connection on both mt
- make bridge interface on both mt
- make eoip interface on both mt and use pptp ip for eoip remote-address
- put eoip and local-ethernet on the same bridge on each mt

i hope it can solve your problems :D

regards
usrox
by usrox
Wed May 09, 2007 2:42 pm
Forum: General
Topic: grouping connections
Replies: 5
Views: 1115

Hi, yes you can use pcq to equalizing your clients bandwith also you can excluding the p2p traffic using mangle and make queue (queue-tree) for your traffic to ensure your clients not taking others bandwith.
by usrox
Wed May 09, 2007 2:01 pm
Forum: General
Topic: HTTP Redirect
Replies: 2
Views: 744

Hi, You can change the www service port with /ip service set www port=8899 and then you can add dst-nat rule :

chain=dstnat dst-address=[public-ip] protocol=tcp dst-port=80 action=dst-nat to-addresses=[local-server-ip] to-ports=80
by usrox
Wed May 09, 2007 1:50 pm
Forum: General
Topic: PPTP connections cannot access local subnet
Replies: 7
Views: 3529

My vpn ip-client (ip-pool) are the same segment with my local-networks 10.xx.xx.82-10.xx.xx.85, I just add 2 NAT rules like my post before and it works perfectly.
by usrox
Wed May 09, 2007 1:40 pm
Forum: General
Topic: Problems for the installation of a RouterOS in a PC
Replies: 7
Views: 1254

Same question as "winxp2000" did. :D
The versions which you try to install are very old.
by usrox
Wed May 09, 2007 1:30 pm
Forum: General
Topic: Problem with L2TP
Replies: 1
Views: 568

Hello, try change the MTU/MRU config to "1400" or "1300" on your l2tp server.
by usrox
Wed May 09, 2007 1:17 pm
Forum: Wireless Networking
Topic: Setting up to act as a simple DHCP wireless router? How?
Replies: 6
Views: 1287

Hi, its more simpler if you build one bridge interface and put ether1 and wireless (AP mode) on bridge. If you want to make the routerboard as DHCP-relay you can use DHCP-relay feature.
I just wondering if you already have routerboard as router why you still use windows

Sorry for my bad english. :)
by usrox
Wed May 09, 2007 12:41 pm
Forum: Wireless Networking
Topic: RB 112 as a Backbone and AP
Replies: 6
Views: 1139

Hi yanuarputra, Yes you can use your 2nd Radio as your clients AP. :D
by usrox
Wed May 09, 2007 12:31 pm
Forum: General
Topic: RB112 and RB133 winbox disconnects?
Replies: 2
Views: 723

Hi, Run "sys reset" and reconfigure your routerboard :D it may solving your problems.
by usrox
Wed May 09, 2007 12:16 pm
Forum: General
Topic: Please help..hotspot and walled garden
Replies: 13
Views: 1741

Hello, you can use incoming/outgoing-filter on user-profile to put your own filter-rules on your user-profiles, so you can make different access type for you user.
by usrox
Wed May 09, 2007 8:41 am
Forum: General
Topic: Problems for the installation of a RouterOS in a PC
Replies: 7
Views: 1254

Hi, are you already try install mikrotik on another disk ? or you can also try install mikrotik on DOM or CF Disk.
by usrox
Wed May 09, 2007 8:34 am
Forum: General
Topic: Hotspot NAT address.
Replies: 7
Views: 1347

If you use masq rule from default config (setup-wizard), hotspot use any public ip on your router.
If you want to specify your hotspot outgoing ip you can change default masq rule with src-nat.
by usrox
Wed May 09, 2007 8:26 am
Forum: General
Topic: PPTP connections cannot access local subnet
Replies: 7
Views: 3529

I have similar problems and i use NAT to reach the local network NAT-VPN-to-local chain=srcnat out-interface=eth-local src-address=10.xx.xx.82-10.xx.xx.85 action=src-nat to-addresses=10.xx.xx.80 to-ports=0-65535 NAT-VPN-to-Public chain=srcnat out-interface=eth-gateway src-address=10.xx.xx.82-10.xx.x...
by usrox
Thu May 03, 2007 9:25 pm
Forum: General
Topic: Port Forwarding not working
Replies: 23
Views: 3513

Hi, i have similar config for port redirect to my local server and it works perfectly chain=dstnat dst-address=[public ip] protocol=tcp dst-port=80 action=dst-nat to-addresses=172.21.2.2 to-ports=80 chain=dstnat dst-address=[public ip] protocol=tcp dst-port=22 action=dst-nat to-addresses=172.21.2.2 ...
by usrox
Sat Nov 11, 2006 2:03 pm
Forum: General
Topic: to help me
Replies: 2
Views: 794

Use Netisntall (for Routerboard) to reinstall and use RB500 packages (-ns)