MikroTik

tagno25

Even after upgrading to 7.13 and trying MANY deferent wireless settings (nstream, security, management protection, etc), we are still experiencing the same problem. It seems like when the 5GHz is flickering that the bonding may be having a problem and dropping some packets on the 60GHz.

tagno25

You may need to configure a scan-list, or something may be incorrect on the AP

According to the LGH5 product page it does not support 5060MHz as a valid frequency.

tagno25

I have multiple CubeG-5ac60ay-SA APs with CubeG-5ac60ay clients setup with "active backup" bonding and have NAT setup in the CubeG-5ac60ay. The problem is that if the 60GHz connects first, the 5GHz will only stay connected for about 10 seconds before disconnecting. The APs say that the cli...

tagno25

I have quite a few RB750UPs that fail to boot after updating routerboot. The only way I can get them to consistently boot is to use the backup boot loader, and then enable force-backup-booter. Is there an update/fix for these routers without replacing them or permanently using the backup boot loader?

tagno25

Even if it cannot be fixed, it would be nice if you could save the syslog logs to disk

tagno25

What's your RouterOS version? It was broken this way (not sure for how long) and was fixed in 6.34.x, but I did not test if the fix made it also in 6.32.x bugfix branch. Then there's another possible problem, but behaviour is different. When DHCPv6 server looks for DNS address to use, it unconditio...

tagno25

If it's mainly DNS you're after, RouterOS DHCPv6 server can already run in stateless mode and provide DNS. Just add new server without any pool, set managed-address-configuration=no and other-configuration=yes in /ipv6 nd and it will take DNS addresses from /ip dns and send them to clients when the...

tagno25

the routers IPs are 192.168.6.1/24 and 192.168.6.2/24
The only bonding I can get to work is 802.3ad, but what I can see that won't work because the links could have differing speeds.
I have tried mii link monitoring, it stays linked with no traffic.

tagno25

I am trying to bond two 700Mbps+ links and bridge them to a 10Gbps link I cannot ping from router1 to router2 with sfp7 and sfp8 in a bonding interface. If I move them directly to the bridge and remove the bonding then I can ping. Here is the relevant "/export compact". Both Agg1 and Agg2 ...

tagno25

The DHCPv6-server currently does not support address delegation, it only supports prefix delegation. The DHCPv6-client supports both.

Without address delegation Windows does not receive any IPv6 DNS servers.

tagno25

Still having the same IPv6 DHCP issue with ROS 6.34rc9 , when requesting a prefix: IPv6 DHCP rc9.png This problem still exists with v6.34rc14. Works fine with v6.33.2 -tp 6.34rc3 added the ability to request a IPv6 address via the DHCPv6-client. You currently have to add the IPv6 DHCP client via th...

tagno25

You currently have to add the ipv6 dhcp client via the terminal. The GUI does not have a way to set the request type (address and/or prefix).

example:
/ipv6 dhcp-client add interface=ether1 request=address,prefix pool=test

If you have request include prefix, then you must set a pool.

tagno25

Have three CCRs, and they all crashed. They were each running a different version (6.26, 6.28, and 6.29) Have a customer that has a CCR that didn't lockup, but don't know if it is poling ntp. It could also be that the others caused it to not be able to update it's clock, so it didn't get the time 23...

tagno25

I am trying to get this working without SNMP, is that possible? Or do I need to enable SNMP?

tagno25

I have a RB450 that had three of the 6.3v 560uF capacitors vent. I replaced them with some 10v 1000uF and it is now working. I was wondering if there could be any issues because of the new caps. They are the two closest to the CPLD and the one next to the CPU.

tagno25

there is also this program, made by another company:
http://itunes.apple.com/us/app/mikroman ... 04767?mt=8

Any for android that you know of?

tagno25

Advertise where? If you mean stateless address configuration, then yes if advertise-dns is enabled. But note that client should also be capable to receive DNS advertisements. Thanks that is exactly what I needed. Because DNS settings are under /ip dns, I was thinking that they were only IPv4 settin...

tagno25

Yes, it is possible to specify IPv6 DNS servers in /ip dns servers list

But does it advertise those?

When I said requests I meant can it act as a DNS cache on IPv6.

tagno25

Does Mikrotik ROS support IPv6 DNS requests?

Is there a way to specify the IPv6 DNS servers? RFC5006?

tagno25

It looks like it may be the same or a similar problem, but I am using the built in switch chip.

tagno25

I am having a problem where my RB750G will not send a router advertisement. I have to take down the Ethernet interface that I am trying to advertise on, then when I bring it back up then it starts advertising. When it tries booting the router attempts to advertise the fe80: address, instead of the 2...

tagno25

and a wireless freak on the moon. literally

Oops sorry, when I posted I accidentally removed saying to try a moon bounce.

tagno25

It would be neat to attempt a 70000km+ link and get it working, even if for only a few seconds.
It would probably require a different radio and a amp though.

tagno25

Is it possible to use nstream dual in a PTMP configuration? or is it strictly PTP?

tagno25

I think I found out what the problem was. When I checked "Add Default Gateway" on the ovpn client, all traffic wanted to go through it, even the ovpn session. :shock: I had to add a static route for the VPN connection IP to the route list to force that IP to go through the correct gateway....

tagno25

emmm, even the forum and firefox can't display that mysterious character are you sure it's UTF8?

Maybe your OS cannot display it? I can see it fine in Chrome on Ubuntu.

http://en.wikipedia.org/wiki/%C5%BD

tagno25

I have seen the exact same behavior. The sad part is this issue won't have any priority as I have said before that everyone else seems to think that they have openvpn running without any issues. I have tried several different configs and have not been successful. I use pptp connections and they sta...

tagno25

Now the log shows "peer disconnected" on both sides Client: 16:31:17 ovpn,debug ovpn-out1: disconnected <peer disconnected> 16:31:17 ovpn,info ovpn-out1: terminating... - peer disconnected Server: 16:34:48 ovpn,info ovpn-xxxxxxx: terminating... - peer disconnected 16:34:48 ovpn,info ovpn-x...

tagno25

Turning on keepalive might help.

I tried turning it on (I set it to 30), but it still does the same thing.

tagno25

Here is some log info from when the OVPN drops. I have a ping going across the link from both sides when this happens. Log on server: 17:46:03 ovpn,info ovpn-xxxxxxx: terminating... - nothing received for a while 17:46:03 ovpn,info ovpn-xxxxxxx: disconnected 17:46:10 ovpn,info TCP connection establi...

tagno25

Any chance of an android version?

tagno25

I have set up a OVPN client and serer. I have it working how I want to, but after a shor period of time the connection stops passing any traffic. To get the connection back I have to disable and then enable the OVPN-client connection. Server: /ppp profile set default change-tcp-mss=yes comment="...

tagno25

change the read group so that "sensitive" is not checked.

tagno25

You should be very careful, it is recommend to grant separate directory for Dude, to make sure it will not happen again. I realize that now and have recovered. But the Dude should not delete all the files, it should just replace the files and if necessary delete the files relating to it and nothing...

tagno25

I found a MAJOR problem in the update script! If you run the dude from outside the proper directory then it can delete everything!!!!!!!! :shock: :shock: I was running the dude on Linux and it prompted me to upgrade it. So I told it to upgrade, it downloaded the files and then started deleting my en...

tagno25

I need IPv6 Queue support as well.

It would be nice if all services supported IPv6.

tagno25

I have the Dude running on my network monitoring some laptops and other devices that have multiple IPs. When the first IP on the address list is unreachable, then the Dude claims that the device is "Down Complete" (it should be "Down Partial").

tagno25

Hi freedns.afraig.org offers 'n Dynamic DNS service, but it order to do so, i need to be able to run the following linux script on the mikrotik. Is there someone that can help me out with it. Want it to update every 5mins and then delete the url it downloaded a few seconds later (otherwise i will s...

Search found 38 matches

Re: CubeG-5ac60ay 5Ghz flapping

Re: SECTOR ANTENNA NOT BROADCASTING

CubeG-5ac60ay 5Ghz flapping

RB750UP unable to boot

Re: Syslog

Re: [Feature request] DHCPv6-server address delegation

Re: [Feature request] DHCPv6-server address delegation

Re: Bridging Bonding interface and sfp+

Bridging Bonding interface and sfp+

[Feature request] DHCPv6-server address delegation

Re: 6.34 release candidate version topic!

Re: ROS v6.34rc6 IPv6 Issue

Re: all CCR crashed

Re: Norification if speed on a link drops

RB450 Capicitor replacment

Re: winbox for windows mobile - minBox

Re: IPv6 DNS

Re: IPv6 DNS

IPv6 DNS

Re: IPv6 radav not sending

IPv6 radav not sending

Re: WR: 304km with RouterOS + XR5 + handmade antenna

Re: WR: 304km with RouterOS + XR5 + handmade antenna

nstream dual PTMP?

Re: OVPN traffic stops

Re: UTF8 characters in system identity name crash console

Re: OVPN traffic stops

Re: OVPN traffic stops

Re: OVPN traffic stops

Re: OVPN traffic stops

Re: winbox for windows mobile - minBox

OVPN traffic stops (Solved)

Re: Security Problem - read only login can see passwords and key

Re: MAJOR Failure in update

MAJOR Failure in update

Re: Winbox and IPv6

Dude ping/service bug?

Re: Wget Afraid - FREEDNS script help