MikroTik

abyss

Hi, WanOs has only gigabit solutions, seems to be too small... We have connected the fiber link directly on the 1072 and directly a server on each side, same result around 619 mbps. Running 10 parallel session go up to 9.98 Gbps I've made a calculation with https://www.switch.ch/network/tools/tcp_th...

abyss

It's routed, but the link was always on the CRS317 ad CRS326 attched to the 1072, this window problem impact the routed traffic on them. We made the crossing VLAN for tests. We will try to mount the link on the CCR1072 directly and see if routed traffic is subject to the same performance problem or ...

abyss

Even is we plug this link on both CCR1072 and do routing or VPLS you think so ?

abyss

ping 192.168.70.15 PING 192.168.70.15 (192.168.70.15): 56 data bytes 64 bytes from 192.168.70.15: icmp_seq=0 ttl=64 time=3.095 ms 64 bytes from 192.168.70.15: icmp_seq=1 ttl=64 time=3.072 ms 64 bytes from 192.168.70.15: icmp_seq=2 ttl=64 time=3.085 ms From S3 to S5 Same result with TCP window size 6...

abyss

Hi, Thanks for your replies, The link was on the CRS317 before, with another layer 2 provider with same ping time due to distance. We had the same result and put the fault on the provider limiting individual sessions. Then we ordered a second link layer1 that was plugged on the the CRS317, same resu...

abyss

Thanks for your comment, I'm not a native english speaker as you can read

If you talk about brand, I'm asking if it's a good idea to make a test with another switch brand. To be sure that's the problem come from a configuration or a CRS cascade.

Sorry.

abyss

Hi, We noticed a performance problem with CRS3xx switches. We are unable to reach more than 350 Mbps per session on this configuration scheme from S3 to S4, and more than 150 Mbps from laptop to S4 https://www.wifx.net/images/forum/testlab3xx.jpg Our 2 datacenters linked by an 10Gbps amplified 320 k...

abyss

Hello Everyone,

I would like to know if the new LtAP LTE kit, LtAP 4G kit and LtAP have an internal GPS antenna ?
If yes, does anybody has experience if the gps is working inside a car ?

Best regards,
Julien

abyss

Hello mikrotik, To increase performance over virtualization, I tried to configure SR-IOV with SR-IOV interfaces or PCI direct devices. I use a standard HP HP 2x 10GbE Ethernet 530FLR SFP+ DualPort with a Broadcom BCM57810S. It's seems that this standard driver is not supported by routeros: https://w...

abyss

You can have a look to your cpu readyness stats running: esxtop command... If you have more than 20% of %ready, decrease your chr numbers of core to fit better your hardware CPU. All our chr runs with 2-4 cores better than 10 or 20. When CPU ready increase over 100%, it crash. https://www.wifx.net/i...

abyss

Hello,

Any news about SR-IOV support ? I tried a configuration and it's seems to be not supported.

Best Regards,
Julien

abyss

Hello, We are using CCR1072 and CCR1036 as LNS servers with L2TP secrets. We encounter a speed limit per L2TP session of 508 Mbits with 1.2 Ghz CPUs independent of CCR1072 or CCR1036. it's seems that L2TP interfaces are limited to 1 core and we cannot activate fastpath because we are using radius an...

abyss

Directly at metanoia, they send us 3 samples... But metonoia support could not help us at the moment...
Our national operator is deploying Gfast and metanoia has also a Gfast module, would be great to be supported soon...

abyss

In Switzerland also most of the lines are VDSL, only 10 percent of fiber-to-home in the major cities...
If we have a ADSL/VDSL interface for Mikrotik, we need more than 300 pieces for our own use and remove all those bridges !

Cheers,
Julien
http://www.wifx.net

abyss

Hi, We bought 3 pieces and made first tries with our VDSL lines. We've tried with a RB962UiGS-5HacT2HnT and 3 VDSL configurations: VDSL2 Vectoriezd 1,5 km VDSL2 1,8 km VDSL annex B, 600m The SFP Modem is good and stable and snr are comparable even better than our current planet VC-231. The mikrotik ...

abyss

Hi,

I can use 6.35.1 cloning the disk:

- upload vmdk
- open ssh session and go to VM folder
- type vmkfstools -i chr-6.35.1.vmdk -d thin yourvmname.vmdk
- use the cloned disk insteed of the original one..

Best regards,
Julien

abyss

Hi, Is Capsman going the way of stacking Mikrotik routers ? It would be a great feature the ability to concatenate multiple Mikrotik devices in one. We have many site with 3 to 5 Grooves, some RB911, and it will completely change the configuration facilities if we can see all wlan's interfaces in th...

abyss

Hi, Controlling clients with access list prevents bad signal clients and low bandwidth. The biggest difference with seamless roaming, multiple AP and unifi is the that clients see only 1 AP and 1 mac-address. This prevent Apple device to constantly jump, register, disconnect over detected APs when i...

abyss

After Doing some tests:

Better configuration seems to be:

wwm enabled
periodic calbiration enabled
hw-protection-mode rts-cts
hw-retries 15
frame-lifetime 0
Adaptive noise-immunity ap-client mode
Disconnect timeout 00:00:15
Distance indoors

Reagrds,
Julien

abyss

This Topic is closed...
Mikrotik Job offers works well...

Welcome Oleg

abyss

Hi,

2.4 Ghz dipole is a good way. I didn't think about using basebox without the cover.... Will give feedback after first freeze and snow....

abyss

The old disable-running-check setting on wlan interfaces is a good way, shame on me

It get rid of OSPF calculation and link brings down/up without disconnecting VPLS tunnels when making changes on frequencies...

abyss

Hi guru's, I've implemented a full ospf network on our network. I really take care for route summarization to have the smallest route table as possible (about 74 routes). Is there a way to prevent VPLS tunnels to fall on the subtrees when I do a change on a base point to point wireless link ? It tak...

abyss

Hi Quared,

Yes of course.
It's planned to associate with him, but he actually has to care about his health so we are searching another engineer until the autumn and surely more.

Best Regards,
Julien Hoppe
http://www.wifx.net

abyss

Hello Everyone, We are looking to hire a Mirkrotik Network Specialist in Switzerland. Our dedicated network counts 750 broadband Wireless Access end users. Our infrastructure is fully Mikrotik. We also manage 200 routers for Corporates. The temporary mandate is: - Manage our network and provide supp...

abyss

Hi Normis,

No the good deal with Omnitik is the one case box, without high frequencies cables and external antennas that "always" fill up with water after some years...

Thanks for reply.

abyss

Is it planned to have an omnitik in 2Ghz Band ? It would be a really great outdoor Access Point :D and I think it's missing in the product list... And is it also possible to consider adding an option in the quickset on RB951Ui to have the default gateway on port 5 ? Feeding an external antenna with ...

abyss

Thanks, I already use nv2 in a large network, with some good results, I try to make it better, prevent pppoe disconnection, saturation, etc... But I didn't answer what is exactly the "built-in QoS policy algorithm" ? I should update the documentation if I can get an answer... For the 2 other questio...

abyss

Hi Everybody, I would like to have more details about NV2 QoS... - What is exactly the "built-in QoS policy algorithm" when nv2-qos=default is set ? Does it prioritize by packet size or something else ? - If mangle rules with set-priority are used, does it pass over nv2 qos default or do I need to u...

abyss

Hi, you need to use proxy-arp on your LAN interface. Create a pool of addresses in the range of your server network but out of your DHCP scope and give thoses addresses with the ppp profile. In the profile, the local address will be your LAN VPN router adress...

Best Regards,
Julien

abyss

Hi,

Just because nobody's connected... Connect a client and the interface will be running...

Best Regards...

abyss

You can specify a pcq rate, for your example 2mbps, or make a queue in a queue using queue tree....
If you don't specify a rate, it will divide the total bandwidth equally between users or connections...

abyss

Try with 36000

Regards

abyss

http://forum.mikrotik.com/viewtopic.php?f=10&t=78315

abyss

Hi,

Is there already a price annoucement ?

Best Regards,
Julien Hoppe

abyss

Ths dst-nat rule, do not specify the public IP, but the in. interface..

abyss

Hi, I'm trying to stabilize at the maximum our network for VOIP needs and as it grows, pppoe disconnections increase. Splitting users in separates VLAN with each time a pppoe service already bring more stability. Removing RIP packets on each interfaces also prevent a lot of disconnections (yes I kno...

abyss

Hi,

Use PCQ to equally divide the bandwith to users:

http://wiki.mikrotik.com/wiki/Manual:Queues_-_PCQ

abyss

Hi,

Specify the in. interface in your firewall rule instead of the IP address.

Best Regards

abyss

Yeah

waiting for it...

abyss

Hi,

Do you already have a release date for this device ?

Best Regards,
Julien Hoppe
http://www.wifx.net

abyss

Hi Mikrotik,

CoreRouters are really amazing !

Is it planned to develop and 10 SFP fiber ports CoreRouter to match backbone needs ?
I actually need 2x CCR1036-12G-4S-EM to have 8x SFP.

Thanks,
Julien Hoppe
http://www.wifx.net

abyss

Hi,

try to make a static DNS entry pointing to your local server and be sure that your wireless devices use Mikrotik DNS...

For example, point myexchange.mydomain.com to 192.168.1.10 (local server IP)

Best Regards,
Julien
http://www.wifx.net

abyss

Hi, I had a response from normis, those settings seems to be better (mix with mine and replies): wwm enabled hw-retries 10 frame-lifetime 100 Adaptive noise-immunity ap-client mode Disconnect timeout 00:00:10 Distance indoors I hope that wmm power-save will be supported soon, would be good for spect...

abyss

Thanks for reply, Why not to use MT :-) ? Did you try to manage 60 TP-Link in a hotel :-) ? I will try your tips... about ack timeout, I have better to set indoors ? Did I also have to grant the success.html page on the HotSpot ? What about WMM ? Is there a setting that MT don't manage in the Wifi s...

abyss

You can find the CCQ clicking on the line in registration tab... TX/RX CCQ

abyss

Hi, Try to decrease power to have a signal around -60 dbm and check CCQ. Configure bridge, station-bridge mode, VLANs or MPLS tunnels, EOIP is havy for processing. Generate and receive your packets from routers behinds your wireless devices, it will increase... but don't expect mo than 99 Mbps, you ...

abyss

Hi, I'm managing and deploying hotels and administrations HotSpot and everybody is complaining about disconnections and speed problems since may this year. After making some tests, it's seems that the problem is generated by the iphones, Ipads and Macbook on the wireless networks... Thoses devices c...

abyss

Hi,

Do I need to uprgrade CPE as well as AP to increase nv2 stability ?

Best Regards

abyss

Ok thanks,

And what about your settings for default-queue, pfifo ? and default-small ?

Cheers,
Julien
http://www.witecom.com

abyss

Hi, Anybody has feedback about this ? I've set up my default-small to 100 and default to 500.. Maybe it's crazy... but my Internet links increases traffic for more than 50% and my cpu's seems to manage that ! Everybody has full speed. What's should be the best settings for a "standard" pppoe server,...

abyss

Hi,

I was really use to see the P Throughput ont stations when running nstreme links...
Is it possible to have it in a next release with NV2 protocol ?

Best Regards,
Julien Hoppe
Witecom Sàrl
http://www.witecom.com

abyss

Hi, I've implemented PPPoE + MPLS + VPLS + NV2 with Qos. Priority informations are crossing all the network for Voip and Video with my rules but.... When a NV2 wireless link in the middle of the MPLS path get to saturation, voice is good but all pppoe-sessions of end-user drop down and does not reco...

abyss

Hi Normis, I've made a test lab and the bug appears also with 3.30-wireless-test package. I'm affraid to find the problem again with ver 5. Clock is ticking normally until I activate nstreme on a wlan interface. When the wlan is in nstreme mode, time is ticking 4 to 10 times faster. Do you think we ...

abyss

Hi everybody, I would lke to know if it's possible to append a string to an url with the web proxy. I would like to add to the google search the string "&safe=strict" when the url contains */images?*, so people will be redirected to */images?&safe=strict*" Is it possible to do it with the "redirect-...

abyss

OK,

I understand what do you mean, I will try and make some tests... I have EOIP tunnels running on the links...

Thanks,
Julien Hoppe
http://www.wifx.net

abyss

Thanks,

But I don't kown how to do that with static routes ? Maybe my schema is not clear enough...
I've made a new one for better illustration purposes:

Thanks,
Julien Hoppe
http://www.wifx.net

abyss

Hi, Did anyone know if it's possible to make one way routing ? I would like to have different route for the upload and the download traffic like the following schema: Router1->wlan1 -----> Router2----->wlan1->Router3 | | |___<wlan2<------ Router3<------wlan2<___| Thanks in advance if somebody can he...

abyss

Hi, I was searching a way to calculate the weekday for enabling different HotSpot settings. This script return the weekday in a global Aweekday variable. Maybe it's intersting someone else... Weekday is returned in the following format: Saturday 0 Sunday 1 Monday 2 Tuesday 3 Wednesday 4 Thursday 5 F...

abyss

Hi, I offently use the WDS mode on my networks to make chains of access points. I've seen on the forum that many users have disconnections like I have. Link stay disconnected on one router for 3 secs to more than 5 minutes, and then AP synchronised again without any user action... I've made a compar...

abyss

Thanks JP, Your printscreens where helpfull for me, I forgett to tag the MKT port for the destination VLAN.... But I have a recent procurve switch and I had to activate also the "VLAN awareness" of each port on the web interface... Awacenter, routers HAVE TO share a common VLAN ID, that's the goal, ...

abyss

Hi, I'm trying to setup a mikrotik to use tagged packets and communicate with a procurve switch and bring phisical separated LAN ports with differents IP configurations... It seems that tagged packets from mikrotik are not understood by the procurve switch and vice versa... Anybody as a similar runn...

abyss

Recompile the etherboot package from http://rom-o-matic.net With the WRAP options, and add include - PXE_DHCP_STRICT WRAP base options: - natsemi:dp83815 -> controller type - Binary ROM image -> ZROM - CONSOLE_SERIAL -> serial console - COMPRESERVE -> don't change serial parameters, use the setting ...

abyss

Hi, I've compiled a new bios for WRAP boards, that include the correct PXE boot paramaters for Mikrotik netinstall. Just upload by Xmodem the right .UPD file and choose network boot from the serial console at next reboot. WRAP2.UPD and WRAP1.UPD http://www.wifx.net/download/wrap111neti.zip Cheers, J...

abyss

Hi,

I've set specials NTFS rights to use exported maps with aspjpeg.
But each time dude's export maps (png), it set up differents NTFS autoristations that are not corresponding to the parent folder's one.

abyss

This is my remarks on the dude usage: - As already mentionned, move elements from a map to another. - Move a link from an element to another, without loosing graph datas. - Assign rights per users on different maps ? Panels ? - Assign a root map per user. - When moving Dude from a computer to anothe...

abyss

So Heinrich, paste the code in the source of a script, it's fully functionnal, you just need to name your EOIP interface (Name) with the dns name, like "blabla.wifx.net", and if you have EOIP tunnels that don't have a DNS, just name it with the IP address directly...

abyss

Hi Normunds, I use this topic to ask you a simple question... Is mikrotik planning to use dynamic DNS resolution ? Because actually I've srcipted most of my routers to run dynamically... For IPSEC I resolve the "proposal name field" to have dynamic policies and for peers, I've put the DNS in the beg...

abyss

I don't know if you're using WPA but I had a similar problem with chains of WDS and WPA security... Networking is working fine, it's only DHCP that's stay requesting.... I've put the clients on a Vitrual AP with WPA support, and WDS interfaces without any keys, directly on the master interface... Re...

abyss

Hello, As mentionned on this post, I had bad performance with multiple channels, regardless of the non-overlapping freqnencies... To increase bandwith on WDS chains I've made some tests with "/sys int wir brust-time". And apparently 1500 [us] is the best setting, for UDP and TCP... But it also solve...

abyss

Since version 2.9.28: :local year [:pick [system clock get date] 7 11] :local start-tmp (5 * $year / 4 + 4) :local start-day (31 - ($start-tmp - ($start-tmp / 7) * 7)) :local start ("Mar/" . $start-day . "/" . $year . " " . "02:00:00") :local end-tmp (5 * $year / 4 + 1) :local end-day (31 - ($end-tm...

abyss

Hi, I have the same problem with two of my clients configurations, I've made some tests and it seems that third box is not working... (cannot ping) with this configuration: Wireless Client ---- MKT1 ---- MKT2 ---- MKT3 ---- MKT4 (Internet gateway) But with this configuration it's ok: LAN Client --- ...

abyss

Yes, really weird, But with staros I have the same result, I was thinking it was from MKT but not... Did anybody do some performance tests running on multiple frequencies at the same time ? I also tried with a couple of hardware, with 1 minipci per adapter, pentium, celeron, WRAP, etc, etc... If I h...

abyss

Hi, I'm doing some tests since 2 weeks now, to improve bandwith on my networks... maybe my questions are quite "amateur" :oops: I've installed two EPIA 1ghz mainboards with 2 routerboard 14 and on each, 3 Winstrom CM9 I can easly get 40 Mbps TCP throughput on 5 Ghz-turbo mode, and 22 Mbps on 2.4 Ghz...

Search found 74 matches