MikroTik

sergioems

ok thanks gonna try it

sergioems

Hello there to all Im having a problem with my RB411 that is working like bridge with a router modem. The problem is that if i setup password when i try to conect using a pc ask me for credentials user and password and only after ask me for network key. And sometimes conect and other times don't. If...

sergioems

in can buy the level 4 just would loose the level 3 license right?
Also for not be half speed how can i setup to repeat with full speed?

thanks

sergioems

so need to upgrade my license. and after just setup as ap with wds? or wich way to configure?
Regards

sergioems

Central with routerboard with level 4 with ap bridge.
Now would like to extend range and repeat signal and have another rb411 but only have level 3 inside.

Any ideias?

sergioems

anyone can clarify me this?
Regards

sergioems

but in bridge mode i can repeat signal?
Regards

sergioems

I have an ap setup with a routerboard with level 4 and know i would like to put a repeater under a distance but i only have a rb411 with level 3 license. can i do anything to this work as repeater?

or what is minimum license to put this working as repeater?

thanks

sergioems

yes i have level 4 on board and i have setup like you said and im unable to get sucess. I will post how i setup for you to tell me what i did wrong. thanks

sergioems

Hi there. i Have a cable modem static ip and a routeboard rb 411 with level 4 with wireless pci that i would like to use as ap and since the modem cannot make dhcp i will use the routerboard to do this. I ve tried to setup like this but was unable to get it working. In wireless mode i select ap brid...

sergioems

Ok. Gonna try and post results. But cable is good is cat6 category and use shiel rj45 plugs

sergioems

Just one radio. The amperage of 24v power suply is 1AMP. I tried also with a 18,5 power suply from laptop with 3.5 amp and im getting same problem. It apear that is just keeps rebooting

sergioems

I have setup with a 24 volt power suply and it gets better something but not very much. Wireless signal always keep getting and going and i lose conection to the rb433.
Does anyone have any idea what it could be?
Thanks

sergioems

setup ad station-pseudobridge and worked superb. thanks

sergioems

here goes the link http://www.interprojekt.pl/katalogp.asp ... EVICE24020

sergioems

in none. i just said i can conect i never said i leave it working:) was just testing purposes

sergioems

no because i still can read and i know protection for my network.

sergioems

Ok. im not an expert on this. what i can say is that i can conect at those distance and get internet conection and all working. i can assure you that just because i tested.

Regards

sergioems

i can show anyone who wants. More exactly i was checking in google earth distance and i get 6.05 km. you can doubt but is true

sergioems

Hi there to all. Im trying to setup a rb411 as station conected to an ap but im not getting there. I ve setup as station and it associates and also bridge setup between ether1 and wlan1 and bridge is working. I get dhcp adress from ap but i cannot ping neither the ap neither have conection to the in...

sergioems

thanks. I was also thinking that:) but now i clarify:)

sergioems

Yes with ligne of sight. My laptop is a dell e4300 with a internal wireless card nothing more. But by ap have an omni of 19dbi

sergioems

Hi to all. I have one client with one rb411 and one senao pci and i would like to know if is possible to conect to 2 aps at same time.
Ex: have 2 pc one conected to each gateway.

thanks

sergioems

i have that configuration in my sistem.
Works superb and have great range. Have conected my laptop to the ap at more than 6 km with ligne of sight

sergioems

thanks for the hint. Gonna buy then a 24v power adapter

sergioems

Hi to all. Im setting up a rb 433 and im having a problem wich i think is power supply problems. I have a cable of about 60 meters and poe suply is 12v and 1amp at the other end of the cable and im getting lose wireless sometimes and when i try it with a smal cable don t have this problems. can it b...

sergioems

And a 411a can be set as repeater from 433?

sergioems

i didn t folow your ideia.
How do i make that? senao is the mini pci on the 411 routerboard. you say to set 411 to station but how do i make that without setting all wireless to station?

thanks

sergioems

Hi there. Im running here a system using a rb433ah setting in ap mode and now i ve bought another rb411 to set up as repeater for a house that is more far away. What should i select to make this rb411 with senao EMP-8603 work as repeater? Bridge? or what? since i don t get repeater option. Thanks Of...

sergioems

Thanks for reply. Managed to get bridge and now working.

Now im facing other problem.

On security profiles have made default profile with wpa-psk key but when seting up one ap as client the security that recognises is WEP and by there for i cannot connect.

why this happen?

sergioems

Sorry for only reply now but i was bit sick this last months So i have setup my network on ethernet1 on ip 192.168.2.2 on this interface Aplied on wireless interface ip 192.168.2.5 and setup the wlan as ap bridge. Now i can conect to the wireless network but don t have internet. I need to setup brid...

sergioems

now i see. Problem i has viewing the 2.9 version:)
Sorry for that.

And how about the bridge i ve asked? I need to setup?

Thanks once again

sergioems

ok. i have tryed to search before but could not found. gonna try and search again

sergioems

thanks for answer.
But what is Nstreme field?

Also there must be a bridge from Ether1 to wlan1 in order to use router on ether1? or can be pluged in any port?

And if needed how do i setup a bridge between this?

Once again thanks for your quick answers.

sergioems

Ok. i will
About the setup of the ap i think i managed to get it work.
Now i would like to know if my card is having the full output since it suport 800mw.

Where do i check or configure that?

sergioems

The security part i have solved. I was using browser configuration but on winbox i was able to set up to the security i want and now is well detected. But i still cannot acess wireless network. Always message waiting for the newtwork under windows wireless configuration tool. Aatched i send my scree...

sergioems

I im thinking in to buy an RB433AH. I would be interested in to know if i can do the folowing. I have 2 adsl conections there and my interested is not to make load balancer ( only will make if this solution not work). I would like to get adsl line in ehternet 1 and make ap with mini pci 1 and get a...

sergioems

enable wireless card and set it to mode "ap_bridge". that will make it as an accesspoint. then just add IP address in the "ip address" menu. I have enabled wireless card and have set up to ap bridge. But i have set up WPA security with a 16 digit paraphrase and when scan network...

sergioems

Finally my order arrived. Bought a Rb 433AH and it apears like great stuff:) About radio card bought a Engenius EMP-8603. Now im a complete newbie in this and have already be able to assign ip to ether1 reading some manuals here. Now i would like to use it as a normal ap to start testing without dch...

sergioems

I im thinking in to buy an RB433AH. I would be interested in to know if i can do the folowing. I have 2 adsl conections there and my interested is not to make load balancer ( only will make if this solution not work). I would like to get adsl line in ehternet 1 and make ap with mini pci 1 and get ad...

Search found 40 matches