MikroTik

Muzaki

There is also a problem with the 6.44.x branch with Radius and PPPoE - radius timing out after a few days of operation. This has been reported to Mikrotik with support file via email. I had the same problem, but it seems like the problem is on CCR (tile) and not on RB100AH (powerpc) When a client t...

Muzaki

There is also a problem with the 6.44.x branch with Radius and PPPoE - radius timing out after a few days of operation. This has been reported to Mikrotik with support file via email. I had the same problem, but it seems like the problem is on CCR (tile) and not on RB100AH (powerpc) When a client t...

Muzaki

Seems like i fiksed it.
I had to uninstall userman package, delete database, the reinstall userman, and load from a backup.
Then queues was correctly created

Muzaki

This is getting strange... I have 2 servers with userman. I one replay, the users get 10Mbps, if the other reply they get 200Mbps. I have tried upgradeing the one that reply with 10Mbps. Even tried rebuilding database. But the strangest thing is that it doesnt fit any profile. The limit fits, but pr...

Muzaki

Just now there was an short power outtage, and 240 clients reconnected. 103 of them got wrong limitation on their queue.

The customer is ofcourse happy when the get faster speed, but the ones that gets lower is not so happy.
If i disconnect them again, most of them gets the correct queue value.

Muzaki

Do you mean Userman config or PPPOE config?

I dont think Fasttrack should help creating wrong queues?

Muzaki

I cant believe that I'm the only one with this problem?

I think its strange that the user gets a wrong profile/limitation

Muzaki

I have a strange problem sometimes with PPPOE limitations. Sometimes it seems like it selects limitation by chance. It may happen when the PPPOE-server has been restarted, but not every time. Now i had about 15 clients with 8-16Mbps limitation in Userman, but when I looked in the queue the limitatio...

Muzaki

Found a problem with hAP ac lite and iphone. (Probably other devices to)
With no WPA, everyting is ok, but if you enable WPA then the wireless disappears, returns and disappears.
My solution was to disable WPS, then everything is ok again.

Muzaki

Im having trouble using NV2 on some (most) of my P2MTP. I use RB912 with RF Element horn at my towers, and RB911 with RF Element Stationbox XL as CPE. (Some are RB711 and Stationbox Micro) 20MHz and both HT enabled There is about 20+ clients. My problem is that with NV2 it seems to peak at 20-23 Mbp...

Muzaki

Is it possible to set total rate limit (rx + tx = total), dynamic rx / tx but limit the total. I know i can set rx and tx, but then a user can use ex 32Mbps + 32Mbps = 64 Mbps. Is there any way I can set limit to total 32Mbps. (ex: 10Mbps + 22 Mbps = 32 Mbps / 20Mbps + 12 Mbps = 32Mbps) I'm using Us...

Muzaki

I upgrade my PPPOE-servers to ver 6.30.2 (Using RB 1100x2) I had to downgrade because my PowerBeams P2P just stopped working for some reason. I did have the time to do any research. I did see a lot of traffic going to the PowerBeams even when the client wasnt connected. Downgraded to 6.27 and everyt...

Muzaki

Still no reply ?

Muzaki

Nobody else has this problem?

Muzaki

I have the same problem. Dynamic DNS serveres is filling up, and the customer cant connect to Internet. After reboot everything is ok for a few days..

Muzaki

In our network we have multiple PPPoE servers, which have fiber link into a central router. Now we have the ability to have a network with PPPoE server at each end, allowing customers to connect to the router that responds fastest. But then comes the challenge of routing. I have tested putting two g...

Muzaki

I've found this solution: http://forum.mikrotik.com/viewtopic.php?f=7&t=29844

One one of them it alreade was set to AP-Client, so i put it to Client. On the other it was none, so i put it to AP-Client.

Hope that helps..

Muzaki

From the log it seems like it is checking connect list, and then the one with strongest signal. Why not just SSID?

Muzaki

Is it poosible to dowgrade a routerboard using autoupgrade?

Muzaki

Mode is "AP-Bridge" There are 8 registered clients on that interface. (two with WDS that are disconnecting) The others have been up fpr a long time

Muzaki

AP: RB 600, ROS: 4.6

Client: RB 532A, ROS: 4.6

Muzaki

On Client: Signal Strength: -74 TX Signal strength: -72 Signal to Noise: 23dB TX/RX CCQ: 80-100 / 80-100 mostly over 90% On AP: Signal Strength: -70 TX Signal Strength: -73 Signal To Noise: 33dB TX/RX CCQ: 80-100 / 80-100 mostly over 90% There are two WDS links on that AP. Both disconnect, but not a...

Muzaki

So far it looks like flash is using most of the CPU when the RB "freezes"...
Perhaps the flash is going bad on some of your boards?

Is there any way to "repair" that?

Muzaki

Try upgrading the bios

system / routerboard / upgrade

They have 2.18.

Muzaki

I have som WDS links that doesnt work like the sould. The suddenly disconnect and reconnect. Others on the same interface is ok. From logging, it seems like there's no SSID on client, but there is.. Any idea? 09:00:48 wireless,info debug: 00:0C:42:1B:46:C8@Danebu_Kongsgaard_Abjora: lost connection, ...

Muzaki

Some of the boards is "online" (pppoe connected) but ping is not responding. If i'm able to MAC telnet into the RB, it shows the IP adress on pppoe-out but cant ping. (no route to host) after restart they can be "fine" When the boards are like that MAC ping from AP is very unstable 170ms to 800ms wi...

Muzaki

So far it looks like flash is using most of the CPU when the RB "freezes"...

Muzaki

Thanks. I will try that

Muzaki

These are used as client antennas. CPU goes to 100% for a long time when pppoe is enabled. But the weird thing, is that some boeards work great. If everyone was slow, i would accept that it's old slow boards, but with the same config, same packages, same ROS they work different. If we take a slow bo...

Muzaki

Most of my 133 / 133C3 / 112 is working very slow if I use them as a router with pppoe enabled.

When pppoe is disabled everyting is fine.

Is there any reson for that?

Somtimes pppoe wont connect, other times pppoe is connected, but nothing works until a reboot..

(Bad english.. I know..)

Muzaki

ether1 stops working after about 30sek with 4.7 on RB433 , RB 532 and RB 133.

OK after enable / disable or phisical unplug / replug

Muzaki

I've got 2 boards (that i know about) with the same error 192 an 333.

192 was running 4.2 an 333 was running 3.30. Booth with upgraded license key What is causing this, and how can it be fixed?

Muzaki

ok. Thanx.

I will try that

Muzaki

I have never made a script like that, but i it would be easy to use "search and replace" in notepad.

My only problem is that export create \

Is it possible to export and get the whole command on one line?

Muzaki

Maybe wrong forum, but someone will move it :) We have multiple pppoe servers on different locations. Is it possible to sync these secrets, without export / import? Is it better to use radius, like usermanager? If usermanager is best, is it possible to import secrets direct into usermanager? I have ...

Muzaki

I know it's an old topic, but did you solve the problem?

Muzaki

How can i add a password to this user. If I paste config into terminal it works fine. Then i just add a line with the password. /system upgrade upgrade-package-source add address=1.2.3.4 user=admin password This will create an error in a *.rsc file when i use import, or run after reset. How can I se...

Muzaki

Would a "/system reset-configuration file=name.rsc" do what you want? It would reset, and then apply the config in the RSC file so that your CPE could connect to the AP for example.

Would love this, but still nothing?

Muzaki

Seems like the upload was interupted..

Muzaki

Thanx that worked. Now with another problem: When i use this: /system scheduler add name=sched_upgrade on-event=upgrade start-date=Oct/09/2008 start-time=02:40:00 interval=30d /system script add name=upgrade source="/system upgrade refresh\r\n:delay 05\r\n/system upgrade download-all reboot-after-do...

Muzaki

I've tried to set up an auto upgrade script. I used an RB 192 as a server, and upgraded a RB411 and another RB192. It worked fine, but I have one problem. When I reboot the RB192 it removes the mipsle package.

How do I set up a server that I can reboot, and still keep all packages?

Muzaki

I think that the printer sends a command to the zyxel router, and it generates a username and password.

I tought that I could use that "signal" to automaticly create a user on RouterOS. We have used routerOS for Hotspot, but then we had to create notes with username and password manually.

Muzaki

Is it poosible to use this printer and Mikrotik hotspot?

We have different printers on differens locations, but no way of logging where the ticket was printed...

Search found 43 matches