Community discussions

Search found 48 matches

by SapieH
Fri Jul 26, 2019 11:47 am
Forum: General
Topic: Load balancing over dual L2 backhaul fibre
Replies: 4
Views: 275

Re: Load balancing over dual L2 backhaul fibre

Thank you. Will give it a try over-night.
by SapieH
Fri Jul 26, 2019 11:45 am
Forum: General
Topic: Load balancing over dual L2 backhaul fibre
Replies: 4
Views: 275

Re: Load balancing over dual L2 backhaul fibre

Thanks for the response.
In our core it is a CCR1036 and the remote network is a RB1100AH X2
by SapieH
Fri Jul 26, 2019 8:52 am
Forum: General
Topic: Load balancing over dual L2 backhaul fibre
Replies: 4
Views: 275

Load balancing over dual L2 backhaul fibre

Good day,

I have two layer 2 back-haul fibers from a remote part of my network. I need to load balance across both fibers.
This part of the network is a separate OSPF area. I have tried using OSPF to load-balance but it does not work. Also tried bonding. No luck

Any ideas?
by SapieH
Thu Jan 26, 2017 7:49 am
Forum: General
Topic: Incoming connection with two wan interfaces.
Replies: 9
Views: 956

Re: Incoming connection with two wan interfaces.

Sob, Thank you for all you time. Much appreciated.
I will implement that in the early hrs of tomorrow morning and will update you.
by SapieH
Wed Jan 25, 2017 9:18 am
Forum: General
Topic: Incoming connection with two wan interfaces.
Replies: 9
Views: 956

Re: Incoming connection with two wan interfaces.

I have proxy-arp enabled on my main Neointernet break out. Could this affect it?
by SapieH
Wed Jan 25, 2017 9:14 am
Forum: General
Topic: Incoming connection with two wan interfaces.
Replies: 9
Views: 956

Re: Incoming connection with two wan interfaces.

Here it is......... 0 X S dst-address=0.0.0.0/0 gateway=41.162.6.1 gateway-status=41.162.6.1 inactive check-gateway=ping distance=1 scope=30 target-scope=10 routing-mark=neoint-route 1 X S dst-address=0.0.0.0/0 gateway=169.239.44.17 gateway-status=169.239.44.17 inactive check-gateway=ping distance=1...
by SapieH
Tue Jan 24, 2017 1:50 am
Forum: General
Topic: Incoming connection with two wan interfaces.
Replies: 9
Views: 956

Re: Incoming connection with two wan interfaces.

I disabled those rules, just in-case, but when I enable both the routes with the routing mark, all internet traffic dies. With only the Neointernet out route enabled, Napa traffic is OK but the Neo internet outbound connections are affected. I have posted my default routes below, although the ones w...
by SapieH
Mon Jan 23, 2017 6:43 am
Forum: General
Topic: Incoming connection with two wan interfaces.
Replies: 9
Views: 956

Re: Incoming connection with two wan interfaces.

Thank you Sob, I have other mangle rules using Layer7 strings voice prioritization and pop3 traffic. But these are on chain post routing. My full mange rules are listed below. 0 D chain=forward action=change-mss new-mss=1410 tcp-flags=syn protocol=tcp out-interface=all-ppp tcp-mss=1411-65535 1 D cha...
by SapieH
Sun Jan 22, 2017 5:15 pm
Forum: General
Topic: Incoming connection with two wan interfaces.
Replies: 9
Views: 956

Incoming connection with two wan interfaces.

I have one main Internet breakout and have now added a second wan interface to Napa. With this enabled, my incoming connections, Rdp, pptp etc, come in in my main breakout but leave on the napa connection. I have enabled the following to try and force them out the connection they came in on, but it ...
by SapieH
Sat Feb 06, 2016 8:21 pm
Forum: Forwarding Protocols
Topic: OSPF no Neighbors
Replies: 2
Views: 1689

Re: OSPF no Neighbors

Thanks. Will check that.
by SapieH
Sat Feb 06, 2016 11:29 am
Forum: Forwarding Protocols
Topic: OSPF no Neighbors
Replies: 2
Views: 1689

OSPF no Neighbors

I have started organizing different parts of my network in separate areas. Most areas come up and distribute all required routes. In two instances, the router on one end shows active interface and neighbor, but on the other side no neighbor shows. I have added the network with the correct area and t...
by SapieH
Tue Aug 12, 2014 10:29 pm
Forum: Scripting
Topic: Hotspot user removal by script
Replies: 8
Views: 12106

Re: Hotspot user removal by script

Paste this into a terminal on your Router board and schedule it to run at midnight
add name="Clear users" policy=\
ftp,reboot,read,write,policy,test,winbox,password,sniff,sensitive,api \
source="/ip hotspot user remove [find];"
by SapieH
Fri Aug 08, 2014 5:23 pm
Forum: Scripting
Topic: Hotspot user removal by script
Replies: 8
Views: 12106

Re: Hotspot user removal by script

Thanx rextended! Working well :D
by SapieH
Wed Jul 23, 2014 7:59 am
Forum: Scripting
Topic: Hotspot user removal by script
Replies: 8
Views: 12106

Re: Hotspot user removal by script

Thank you for your suggestion. I am not using usermanager. I need to delete all entries under the user list in Hotspot. The reason for this is that hotspot users get 400mb free and thereafter they need to purchase access through the portal on the landing page. I have a script in place to remove all ...
by SapieH
Tue Jul 22, 2014 10:24 am
Forum: Scripting
Topic: Hotspot user removal by script
Replies: 8
Views: 12106

Hotspot user removal by script

I need a script that will remove all hotspot users at 00:00 every night. My hotspot is running on Ros6.15
by SapieH
Fri Aug 16, 2013 11:17 am
Forum: General
Topic: Hotspot trial limit by usage not time
Replies: 10
Views: 4153

Re: Hotspot trial limit by usage not time

The scheduler is working ok.
But how do I apply the complimentary access when a user log onto the hotspot for the first time?
Can you maybe post your setup here. It would be a great help .
by SapieH
Fri Aug 16, 2013 10:19 am
Forum: General
Topic: Hotspot trial limit by usage not time
Replies: 10
Views: 4153

Re: Hotspot trial limit by usage not time

Thanks Stan,
Will give it a whirl
by SapieH
Thu Aug 15, 2013 8:27 am
Forum: General
Topic: Hotspot trial limit by usage not time
Replies: 10
Views: 4153

Re: Hotspot trial limit by usage not time

Thanks Cstan,
One thing more, to clear the users every 24 hrs how do Imodify the script?
by SapieH
Wed Aug 14, 2013 6:24 pm
Forum: General
Topic: Hotspot trial limit by usage not time
Replies: 10
Views: 4153

Hotspot trial limit by usage not time

Hi All,
I am wanting to limit the trial on my hotspots by usage mot time.
In other words, A user logs onto my hotspot and receives say 200Mb complimentary service, thereafter he needs to purchase access.
Any ideas??
by SapieH
Thu Jul 25, 2013 3:17 pm
Forum: General
Topic: Hotspot setup with Radius Manager
Replies: 7
Views: 3453

Re: Hotspot setup with Radius Manager

Got it sorted. Thanx to eben at Cape Connect :D
by SapieH
Wed Jul 17, 2013 8:15 am
Forum: General
Topic: Hotspot setup with Radius Manager
Replies: 7
Views: 3453

Re: Hotspot setup with Radius Manager

Thanx for that Tim, I have got it sort-of working by following that. 0 D ;;; gateway.netcash.co.za hotspot1 allow 0 1 D ;;; gateway.netcash.co.za hotspot1 allow 0 2 D hotspot1 allow 0 3 D ;;; acssb.bankserv.co.za hotspot1 allow 0 4 D ;;; 3dsecureprd.fnb.co.za hotspot1 allow 0 5 D hotspot1 allow 0 6 ...
by SapieH
Mon Jul 15, 2013 4:55 pm
Forum: General
Topic: Hotspot setup with Radius Manager
Replies: 7
Views: 3453

Re: Hotspot setup with Radius Manager

Hi satish

It was not ticked but Ihave done so. Problem persists. Page not available on https but available on http.
Any other ideas??
by SapieH
Fri Jul 12, 2013 9:08 pm
Forum: General
Topic: Hotspot setup with Radius Manager
Replies: 7
Views: 3453

Hotspot setup with Radius Manager

I have Radius Manager 4.0 and am setting up a hotspot. The Radman setup with integration to Netcash works 100%. My problem is with the walled garden entries to allow clients to reach the buyias.php page and then authenticate to Netcash. It seems as if all port 443 traffic is blocked. if I change my ...
by SapieH
Wed Jul 25, 2012 7:46 am
Forum: General
Topic: how to route packets out of network
Replies: 3
Views: 410

Re: how to route packets out of network

Guys, Thanks for the info. Much apreciated :D
by SapieH
Tue Jul 24, 2012 10:53 pm
Forum: General
Topic: how to route packets out of network
Replies: 3
Views: 410

how to route packets out of network

I need to route packets out the same wan as the one they enterd on Any ideas??
by SapieH
Tue Jan 17, 2012 7:22 am
Forum: General
Topic: recomendations for a switch for core of network
Replies: 2
Views: 672

Re: recomendations for a switch for core of network

I use an RB1100AH. If I had to buy now Iwould go for the 1100AHx2
by SapieH
Tue Jan 17, 2012 7:08 am
Forum: General
Topic: Forwarding a puplic IP to CPE
Replies: 5
Views: 1146

Re: Forwarding a puplic IP to CPE

I have changed the accept rule to a netmap, but have had no success
by SapieH
Mon Jan 09, 2012 8:00 pm
Forum: General
Topic: Forwarding a puplic IP to CPE
Replies: 5
Views: 1146

Re: Forwarding a puplic IP to CPE

Done all that. The Cpe now has the IP and if I check on my core router there is a route for it. But I can not ping it from outside my network. I tried with proxy arp enabled, then I can ping it from the internet. Problem then is that any trafic coming from the Cpe to the internet shows as coming fro...
by SapieH
Tue Dec 20, 2011 9:37 pm
Forum: Wireless Networking
Topic: Apartment Wireless Blanket, groove + ?
Replies: 10
Views: 2021

Re: Apartment Wireless Blanket, groove + ?

Hi richedav,

Your solution sound interesting. Can you give me more detail?
by SapieH
Fri Dec 09, 2011 7:27 am
Forum: General
Topic: Forwarding a puplic IP to CPE
Replies: 5
Views: 1146

Re: Forwarding a puplic IP to CPE

thanx fewi,

taking it one step further, can i setup a nas on cpe with the public IP in my radius and the subscriber can then do a dialup from his Juniper as he would on any adsl line?
by SapieH
Thu Dec 08, 2011 9:09 pm
Forum: General
Topic: Forwarding a puplic IP to CPE
Replies: 5
Views: 1146

Forwarding a puplic IP to CPE

Can anyone advise me how to forward a public IP to the CPE with out dstnat and srcnat. My nework is a fully routed network running on OSPF.
by SapieH
Sat Aug 27, 2011 8:09 am
Forum: General
Topic: RouterOS 5.6
Replies: 28
Views: 8354

Re: RouterOS 5.6

Hi - I run my whole Network of 19 AP's on 5.6 with OSPF. No problems. The stability on the wireless side is greatly improved. Would be great if we could get the kind of throughput the Radwin guys get :D
by SapieH
Thu Feb 18, 2010 9:40 am
Forum: General
Topic: RouterOS v4.5 released
Replies: 92
Views: 21453

Re: RouterOS v4.5 released

Hi phendry We have done some tests using 5GHz-only-N. As far as I know you can not use N-streme in conjunction with -only-N. Up to 8km link we have reletevely stabe performence using R52N both ends. We then set up a 29km link and experienced exactly the same problem as you describe. As soon as you l...
by SapieH
Sun Oct 18, 2009 10:30 pm
Forum: Forwarding Protocols
Topic: How do I bypass the masqurade rule
Replies: 19
Views: 3482

Re: How do I bypass the masqurade rule

on which rule ??
Have tried it on the genral maqurade rule but it does not accept
by SapieH
Sun Oct 18, 2009 8:53 pm
Forum: Forwarding Protocols
Topic: How do I bypass the masqurade rule
Replies: 19
Views: 3482

Re: How do I bypass the masqurade rule

I have a router pc with 9 ether ports. ether 1 - 192.168.102.1 - from rb600 with back bone links ether 2 - 192.168.101.1 - from rb433 public hotspot ether 3 - 192.168.103.1 - from internet ether 4 - 192.168.104.1 - pc ether 5 - 192.168.105.1 - from radius manager ether 6 - 192.168.106.1 - from rb433...
by SapieH
Fri Oct 16, 2009 3:25 pm
Forum: Forwarding Protocols
Topic: How do I bypass the masqurade rule
Replies: 19
Views: 3482

Re: How do I bypass the masqurade rule

I need to masqurade my network as I have private IP ranges internally and the internet only sees my public IP
by SapieH
Thu Oct 15, 2009 11:48 pm
Forum: Forwarding Protocols
Topic: How do I bypass the masqurade rule
Replies: 19
Views: 3482

How do I bypass the masqurade rule

I need to bypass the masqurade rule on my router pc for all trafic to the voip server on IP 192.168.108.2
This critical as the voip server must see the IP of every incoming connection and not all of them coming from the router pc.
Any ideas???
by SapieH
Sat May 30, 2009 8:24 am
Forum: General
Topic: 30 chanel PRI over Mikrotik
Replies: 9
Views: 1756

Re: 30 chanel PRI over Mikrotik

I am looking into this. Thanx
by SapieH
Sat May 30, 2009 8:21 am
Forum: Beginner Basics
Topic: Spliting local and international traffic
Replies: 22
Views: 3915

Re: Spliting local and international traffic

Thanx. This works perfectly!! :lol:
by SapieH
Tue May 26, 2009 9:59 am
Forum: General
Topic: 30 chanel PRI over Mikrotik
Replies: 9
Views: 1756

Re: 30 chanel PRI over Mikrotik

Thanx Guys!! :D
I am at present runnig a dual nstreme link of approx. the same distance and am getting UDPfull duplex 23.6Mbps and tcp 14.2Mbps.

Will I then be able to place our sip/iax2 server at the end of this link andhave only a "converter"to and from E1 at the other end?
by SapieH
Mon May 25, 2009 1:45 pm
Forum: Beginner Basics
Topic: Spliting local and international traffic
Replies: 22
Views: 3915

Re: Spliting local and international traffic

This will work, but I am having problems with my static routing as there can only be one default rule. Any suggestions??? I am using my Mikrotik main router to dial on the adsl lines with the modems in bridge mode. Ether 1 dials international and eather 6 local.
by SapieH
Mon May 25, 2009 7:09 am
Forum: General
Topic: 30 chanel PRI over Mikrotik
Replies: 9
Views: 1756

30 chanel PRI over Mikrotik

Does anyone know whether it is possible to do a point to point link for transporting a 30 chanel PRI over Mikrotik??
by SapieH
Mon May 25, 2009 6:57 am
Forum: Beginner Basics
Topic: Spliting local and international traffic
Replies: 22
Views: 3915

Re: Spliting local and international traffic

Thanx. Let me do that.
by SapieH
Wed May 20, 2009 9:17 pm
Forum: Beginner Basics
Topic: Spliting local and international traffic
Replies: 22
Views: 3915

Re: Spliting local and international traffic

This almost works. There is tx on the local interface but virtualy no rx. How now???
by SapieH
Mon May 18, 2009 4:09 pm
Forum: Beginner Basics
Topic: Spliting local and international traffic
Replies: 22
Views: 3915

Re: Spliting local and international traffic

Thanx!! I shal try that
by SapieH
Mon May 18, 2009 1:47 pm
Forum: Beginner Basics
Topic: Spliting local and international traffic
Replies: 22
Views: 3915

Re: Spliting local and international traffic

Hi can anybody help me????? :D
by SapieH
Thu May 14, 2009 8:55 pm
Forum: Beginner Basics
Topic: Spliting local and international traffic
Replies: 22
Views: 3915

Re: Spliting local and international traffic

Thanx for the link. My problem is not with the mangle rules and I do not want to add a que. I need to direct international traffic to one ADSL line and local traffic to another ADSL line. Do I need to dstnat or route the traffic These are my mangle rules: add action=mark-connection chain=prerouting ...
by SapieH
Wed May 13, 2009 10:09 pm
Forum: Beginner Basics
Topic: Spliting local and international traffic
Replies: 22
Views: 3915

Spliting local and international traffic

I have two Wan's (PPPoE dial up from my x86 pc) wan1 has international traffic and wan 2 has local traffic only. I whish to split local and international traffic according to my local address list. I have created all the mangle rules and they work fine. How do I go about routing the traffic to the r...