Just a question, do you have cell coverage at your high sites, if yes you can use a gsm commander. It will monitor your voltage, can restart your device if a hang is expierenced, It can disconnect your devices at low voltage. I have all my high sites using these devices. it will send sms to me if lo...

This script will check the inbox for a sms voucher (Format is *123443211234#) sent by me. it will forward this message to "132" (Namibia recharge number) delete the sms, receive the recharge message from the cell provider and mail it to me. I set the script to run every 30 min, if there is...

Not being a programmer, modified the script from Base122 to check the inbox fo a sms with a recharge voucher every 30 minutes. This would then forward the voucher to my cell provider in Namibia, recgharge my credit, delete the sms and forward me the recgarge sms received after the recharge cycle, an...

I have now created this script to forward a sms from the RB to the 3G data provider to recharge my credit. I need help however to only forward a sms in the inbox from a certain number, (and if it contains nothing, do nothing) other wise it might forward everything in the inbox to the Cellular provid...

Great

Thanks to Base122, it is working like a charm.

Hi

What was the result, I would like to see your script as I am battling with the same.

Thanks

Hi

That is my problem, I do not know the command to read the sms response and write it to a text file to mail, or alternatively to sms it to another number

Hi I am not good with scripting at all, but I want to have a script to dial 131 (Namibia prepaid 3G) once a week, receive the the credit balance and mail me the details. many thanks OK, I have added /tool sms send usb4 "131" message="1" to scripts and it works, I am now looking a...

HI Rumiclord

Is it possible to post your setup, I need similiar setup with hotspot but my mesh experience is limited and examples is few. Thanks

My RB600 with 4 5Ghz Antenna on top of the mountain here in the south of Namibia. it links to Skorpion Zinc mine about 24 kilometers away to provide coverage to the town. The other end is connected to a 10 Mb ADSL line with Ubiquiti's SR-71 doing the back haul, and Mikrotiks doung the routing, hotsp...

I have a Fritz box ADSL 10 Meg down and 1 Meg up with a Mikrotik RB450 behind it. My problem is I src-nat all outgoing traffick, which works well. I now added a Polycom ip video conference unit to the ethernet 3 port. All connections from this unit works well, but the moment I add a destination nat ...

That I do understand, I just tried to not use the cisco.

I guess I though there would be an easier way of doing it, thanks for your help

As I said forget the wlan interface, leave it disabled. See the pic. Lower left corner is the MT (Amica Guesthouse) Right hand corner is the Mikrtik (Unsupported device) I need to route from Amica to the MT right hand corner for outgoing traffick, No nat involved at this time. everything on this net...

The 2nd router 172.17.11.214 is on another interface. 172.17.11.1-172.17.22.1 are on the same Cisco core, and not propogating routes to the MT. So mt 172.17.22.200 is 30 km from the core 172.17.11.214 is 5 km from the core just to give you a mental picture.

So what you are telling me is that I cannot route from router to anther router if the particular vlan is not assigned to it, not all routes on the internet are attached to every router in the world.

As I am using about 30 vlans how do I then connect them, what is the function of distance scope etc.

The 172.17.11.214 is not attached directly to the MT

it is 172.17.22.200 -> 172.17.22.1 -> 172.17.11.1 -> 172.17.11.214

See picture

Maybe I am expressing myself wrong. I have a 172.17.0.0/16 network, my MT is 172.17.22.200 gateway 172.17.22.1, My ADSl gateway is 172.17.11.214. I can ping from both sides, (forget my wlan interface and ip.) I now want my MT to route all unknown traffick out the gateway 172.17.11.214. (Can ping it ...

Hi SurferTim it does not, as it does not get default routes from my Cisco equipment, and I have two routes out of the network, 1 for official traffick and one for visitors where they use the backbone for connectivity but are routed out on a different gateway, bypassing all sensitive equipment on oth...

Hi SurferTim /ip route add disabled=no distance=1 dst-address=172.17.0.0/16 gateway=172.17.22.1 scope=30 target-scope=10 My route 172.17.0.0/16 gateway points to all 172.17 traffick, and it works but I want 0.0.0.0 to route to 172.17.11.214. I can ping this interface from the MT. But the route 0.0.0...

Hi Cieplik These are my actual ip's and routes. /interface ethernet set 0 arp=enabled auto-negotiation=yes disabled=no full-duplex=yes l2mtu=1526 mac-address=00:0C:42:97:05:D4 mtu=1500 name=ether1 speed=100Mbps /interface wireless security-profiles set default authentication-types="" eap-m...

You can use any radius server (Freeradius) or user man on the same MT or on another MT. Setup the hotspot and use one central database for authentication.

I have a routed network, with a rb450 and userman sitting on the 11 vlan @ 192.168.11.214, one hotspot sitting on the same vlan at 192.168.11.250, one hotspot sitting on the 192.168.22.250 vlan etc. Radius authentication is working fine but the moment I enter a second gateway on the 22.250 hotspot t...

Thanks, will do it this way, consider my request closed.

Hilton

I fully understand the workings of the mikrotik, I want the user using a laptop to send via the wireless network through the cell a sms.

Hi Hilton My aim is to have a mikrotik with solar power on the mountain, connect a cell to the mikrotik and beam the mikrotik to the farm house. Our cell towers in the country side does not cater for 3G, just normal phoning and sms'ing. I need to have the people send a sms via the mikrotik to the ne...

Hi Normis I am looking for someway of connecting a cell our cell router to mikrotik to enable friends on the farm to send and receive sms. There is no telephone and cell reception is 10 kilometers away, and cell repeaters are way to costly. Any help will be appreciated and can be extended to a few f...

Hi I ultimaltely want to bridge 2 stations to one AP, to same lan segment, i.e AP is 172.17.17.200 station one and two must be part of the same lan, as we need to connect remotely to the computers connected to the stations. As EOIP can handle one connection without natting or firewalling, how do I i...

Thanks for the quick response, is there a document to explain it to me.

Hi I one Mikrotik setup with EOIP, and it works fine, my question is I have to connect another site to the AP, but EOIP can only have one tunnel. My dilemma is thye particular VLAN 172.17.17.0/24 needs to be extended to 2 sites through one AP. How can I setup both clients to be part of the same VLAN...