MikroTik

agjini

hello, today i tested one of the links with ub5 and 24 dbi jirous extreme antenna, link is aligned only with eye I have not made alignement properly. the test was made with laptop and mikrotik bandwith test tool at remote site. distance 3km. frequency 4980 width 40mhz. Signal lever 32db laptop---Rad...

agjini

i have purchased two license from them, one prime and one bis, the only problem that i have is that i cannot scan and is difficult to put radio on clear chanel without scanning but i have made some tests, one is made with prime version and mikrotik 411ah and r52 i was able to archive 35/35 fdx, the ...

agjini

you can use dual polarization 24dbi antenna ex jirouse with rb433ah and 2 ub5 cards, one for transmit and one for recive, load the rb with RadioOS from asn.pl software and you will have a 97mbps/97mbps true speed. I have just tryed a link with one polarization with a simple one card A only r52 i got...

agjini

still waitng for a guide, pls mikrotik support

agjini

i have added a image for ilustration, what i need is how do i configure peer from e1 to e2 thru 10.0.98.0/24 link and how to apply filters, i think "filters" is where i make mistake.

thank you

agjini

any help please, i have this in production use and i am still looking for a solution,

agjini

hello and happy new year to all. i am trying to make a failover solutions with two routers and one provider, router E1 primary has wan ip address 10.10.10.10/30 gateway 10.10.10.9 this is active router router E2 backup has wan ip address 10.10.10.14/30 gateway 10.10.10.13 this is backup router as645...

agjini

yes but this link is in production and i dont want to make test with it, i need other links and i am thinking to order again jirous antenna whic cost 450 euro here for a pair and i dont want to spend money if i cant reach results :) i dont know if anyone has had any issue r52n with nstreme-dual opti...

agjini

hello, i have a link nstreme-dual with 2 r52 cards at 800m .its up for more than a year with thrughput 50-60 mbit fdx stable in 40mhz chanel, i want to know if anybody has a similar link but with n cards with single chain ,i want to reach near 100mb fdx is it posibile with nv2 ? extra info :signal s...

agjini

thank you, i have allready tryed that onfiguration but doesnt work with cisco in the midle. its strange . i connect x86>to rb433 and i can ping vlans but if i disconect and connect thru a switcher with that config it stop communicating. i have remake all vlans trunks diffrent times but unsucesefull....

agjini

Hello, i need help to pass 3 vlans from mikrotik 433 >>cisco3524>> to mikrotik x86 i have test direct connection mikrotik >mikrotik is ok .but with cisco between them seems imposibbile . i have configured two port trunk on cisco added 3 vlan to them and to vlan database also but i cant ping vlans . ...

agjini

You can for example buy a 24 v 150-250w switching power supply and a cat5e patch panel , inside patch panel bridge ports ex: 1+2 3+4 5+6 until port 24 so you can make "12 poe " with one patch panel , after that solder a wire on all 4,5 and 7,8 wires to the ports but only on 12 ports ex: po...

agjini

I think is a a good idea, the only problem HDD of server must be IDE so you cant use a high end server , I have tested but not in production, i was thinking same solution as you to have a failover access concentrator and core router, it will be very good if mikrotik support scsi in the future versio...

agjini

I am ok with you with Mesh-WDS, but i was asking how to configure next links , should be all AP-WDS ? like the first Bakchaul or ? i will try to create example setup in my work place to test befoure.

agjini

thank you for your rapid answer, Can i use this setup : Bridge_xxx mode rstp and add ethernet and both wlan 1 and 2 on this bridge on main BH, using diffrent ssid on wireless config for difrent links and use wlan1 and wlan2 as AP-WDS, should i use same setup an all backhauls or i should use Station-...

agjini

i have read that setup, but it use one ethernet card and one wireless card,i dont have same setup, this is diffrent from me, Should i use AP wds on main backhaul directed to sites 2 AND 3 and configure them as client wds on first card than as AP on second card directed to site 4 ?

agjini

Hello to all, i have this schenario where one RB433 act as backhaul to 2 other sites (site nr 2 and site nr3) the communication betwen them need to be wds becouse i use vlans on the AP which are aso RB433 with 3 sectors each. i need to add another site (site NR4 ) this site will have backhaul site n...

agjini

hello. i have infinite problems with a rb333 with 3 r52h cards . i am trying to supply it with poe over a distance 90m with cat6 awg-24 cable but without success, i have tryed with a power sypply 24v 1.5 ah but the rb333,it start up well and after last beep i see connect-disconnect to my network car...

agjini

hello. i have infinite problems with a rb333 with 3 r52h cards . i am trying to supply it with poe over a distance 90m with cat6 awg-24 cable but without success, i have tryed with a power sypply 24v 1.5 ah but the rb333,it start up well and after last beep i see connect-disconnect to my network car...

agjini

i have had this days some problems also with dns , give a try opendns.com

agjini

any one know how to set idle-timeout for pppoe client to 0 or blank ?. i see this option can be configured on modem router ADSL
thnx to all

agjini

thank you for your answer. my configuration is mikrotik/pppoe-client >> telecom adsl provider. I see one connection pppoe-client from mikrotik is up for more that 7 hour but if it has not trafic it will disconnect and try to reconnect again every one minute, but the same adsl modem & user if i m...

agjini

i see none answer on this forum . anyway thank you. i will find a solution .

agjini

Hello. i have a configuration when mikrotik is connected to cisco switch trunk and inside it travel 5 vlan. every vlan on cisco has a adsl modem connected to it and mikrotik do the pppoe-client for this modems that are in bridge mode. The problem that is that pppoe-client disconect every 60 sec if i...

agjini

i see none answer , thank you , anyone has tryed rb411 with r52 and 12 dbi omni as wds repeter ? i am new to this forum but i see small activity , any one can sugest a wds repetter that he has used. i am interested to know little more about the throuput and if can handle about 10-15 clients with 128...

agjini

maby you need this

agjini

this is what i have in mind on my first post, 3 station-wds omni 15dbi with bullet2H linked with one virtual ap for each sector, in total 9 wds-station with 3 frequency in use , this will be a config for some month only i think, i want to change to basestations or minimum true mesh-hardware with mik...

agjini

i want to cover example an aerea of 2x2 km , we have in the middle an AP with one omni sectorized 3x120 degre 16dbi from pacific wireless with rb333 and 3xr52h cards. this will serve for home users with cpe. I want to know if will be possiblie to link wds 9 ap omni 15dbi 3 for each sector but at bas...

agjini

i think too, i have tryed with a rb in a short distance i can connect pppoe also but signal is 50% at 3 metter dist, so is PA.
If i use a small tx power that default settings could i controll this card-failure in the future?

agjini

thank you. in fact i have exchage it sudenly this morning and everything is ok but i am curious what happend to that card , i have 14 pcs stock and i am afraid for the rest. i have also made misurement to diversity ic versus ground and compared to a new card the values are similar .i dont think is d...

agjini

hello, i have mount one ap two days ago and for 24 hour it was ok until yestoday midnight signal was to low, i have checked today both sectors have 1 line at laptop signal metter (message:signal strength very low) at distance of 30metter clear line of sight. my config is rb4333 with two r52h, no ove...

agjini

Normis can you pls check my config for any error .i have not to much experience with mt. i think somthing dont go with rules in firewall , i dont se packet counter to count (only a small quantity) maby i am missing source address.

agjini

input routes manually. (detach add-default-route on dial-out). ?? i am looking for similar but cant find. pls what do you mean. I am not dialing pppoe client for adsl-modems from router. i have two pppoe servers one in Lan interface an second is another router which has pppoe server for AP and a lin...

agjini

i forgot to tell net_bridge is a bridge interface with Lan port on it , and the pppoe for lan customers is on net_bridge. i have removed it and changed rules from net_bridge to lan but the same .i have trafic only on adsl26190 (adsl1) add action=mark-connection chain=input comment="" disab...

agjini

TAKE A LLOK AT THIS . I FOUND GOOGLEING it has two sides one for AP and one for link i think.

agjini

hello to all. I have have one MT ver 3.24 router x86 with 2 wan-s (adsl26190) (adsl32614), one with lan (name=Lan) with one PPPOE server atached (about 25 clients on it) ,and a second lan (name=trunk_AC) that is pppoe AC for an AP (2 clients) All i need is to have a load balanced router .I have trye...

Search found 36 matches

Re: 4km PPTP link with 100mbits full duplex

Re: 4km PPTP link with 100mbits full duplex

Re: 4km PPTP link with 100mbits full duplex

Re: edited: need ibgp between two ROS , HA failover, interes

Re: multihomed BGP two routers one provider ibgp help

Re: multihomed BGP two routers one provider ibgp help

edited: need ibgp between two ROS , HA failover, interesting

Re: replace nstreme dual with nv2 ?

replace nstreme dual with nv2 ?

Re: help need with vlan and trunks. interesting theme

help need with vlan and trunks. interesting theme

Re: Centralise Power supply for RB433...

Re: Production router with ESXi ?

Re: 4 WDS sites connected together config help

Re: 4 WDS sites connected together config help

Re: 4 WDS sites connected together config help

4 WDS sites connected together config help

rb 333 poe needed ?

rb 333 poe needed ?

Re: DNS errors on MT 3.24 on RB333

Re: pppoe-client from mikrotik for adsl provider

Re: pppoe-client from mikrotik for adsl provider

Re: pppoe-client from mikrotik for adsl provider

pppoe-client from mikrotik for adsl provider

Re: idea WDS what do you think ?

Re: Link PTP WDS don't work!!

Re: idea WDS what do you think ?

idea WDS what do you think ?

Re: r52h problem i think, any help?

Re: r52h problem i think, any help?

r52h problem i think, any help?

Re: PCC load balance help

Re: PCC load balance help

Re: PCC load balance help

Re: Best enclosure

PCC load balance help