no differnece between 4.3 and 4.4 over 802.11n difficult link. regards Ros The thing is that in older ros versions the small packets were not pooled or the link was repeatedly reassociating/disconnecting. the same but nstream also stop working on non-N wireless cards (Atheros AR5413). The same mess...

3gz, 1 Gb ram, version 4.2. I have 2 peers for announce my AS with isp 1 and isp 2 with deny in filter. When starting downloading routing table( aprx. 300 000) from any isp via my established peer(by changing in filter rules), the memory leaking from 950 mb to 200 mb, 100% load still after downloade...

pc-based working too with some switch tweak

but anyway id is unknow symbol

how to use it for dhcp with option 82? I want to get via dhcp static ip addrss for switchX+portY

yes..today.. working on 4.04, on routerboard rb 450
not working on PC-based 4.04

but anyway id is unknow symbol

how to use it for dhcp with option 82? I want to get via dhcp static ip addrss for switchX+portY.

4.04b
edge-core 3526

I don't see any 'Agent * Id' columns in your screenshot.

I meant the following:

Clipboard01.gif

If you don't see any - then there's no Option82 ))

i dont see nothing
but from switch go out option 82// i see it via wireshark

'Agent * Id' columns in DHCP Server - Leases tab - was empty too.
Do i need write switch Ip address in DHCP server on Mikrotik?

maybe i do something wrong? in Lease agent circuit ID and agent remote id is empty.

many operation step-by-step.. in 5 time more..possible will sending 5 line in one frame via ssh?

I've use mikrotik like boarder gate, shaper, bgp. My billing via ssh do only one thing - add and remove ip address "X" to address-list "Y". Now I need dynamic assign public ip adresses for local adresses from address-list via NAT. For example: pool "one" 95.95.95.0/24. ...

ok.. its fixed. stay some problem with frame police.

find mistake... was checked "use service tag"

Hi, If you properly set trunk connection from switch to MT it should work. What switch is it? edge-core 4612 config is: vlan 100(10.0.0.1/24) from dlink 3526---> port9 (edge-core 4612( only vlan 1) port10-->mikrotik vlan 100 (10.0.0.2/24) if i create vlan interface 100 with 10.0.0.3/24 on Egle-Core...

I cant get working vlan between l3 switch and mikrotik. For examle i've got tagget vlan id 100(ip 10.0.0.1/30) from switch, and i created vlan interface on the ethernet interface which connected to switch. vlan id 100 (ip 10.0.0.2/30). So i cant ping 10.0.0.1. What i do wrong?

and when you just use Scan do you see other networks? no you can check your router now - it should be working as we placed a fix there. I've make test fixed 4.04 with 4.03( the same cards). From 4.03 to 4.04 data transfer with normal rate, from 4.04 to 4.03 data transfer with rate 10-50 kb. Signal ...

and when you just use Scan do you see other networks?

no

AR928X (AR5BHB92/AR5009)..miniPCIe
AR5008E-3NX(AR5BXB72) miniPCIe


don't work in 4.04b. i dont have other card for test.

i thinking that the problem with PCIe wireless cards because miniPCIe on chip AR5008E-3NX(AR5BXB72) dont working too but was working in 4.03b.

please write to support@mikrotik.com with supout.rif attached

sent

Try turning off adaptive noise immunity on both sides..

adaptive noise was off

downgrade to 4.03 - everything work again

ps.
wireless card on chip Atheros AR928X (AR5BHB92/AR5009)AR5BHB92..miniPCIe

after upgrade from 4.03 то 4.04 my wireless connection via N-card absolutly DEAD in all modes (5 g too) Interface enabled but dont scan nothing.

how long waiting for beta4 ?

i was try mask 32 but don' tworking too

after upgrade to 4.0 beta 3 can't find solo ip address in address list:

its work
:put [/ip firewall address-list find address=192.168.0.0/16]


its don't work
put [/ip firewall address-list find address=192.168.1.100]

i was testing noname(AR5418) miniPCIe wireless card with 3 connectors via miniPCI adapter.. but used only 2 connectors and have got result like r52n.

i've got good stability with manual data rate setting (disabling all exept msc 0,7,8,14,15, it possible make via Winbox if you check Data rate- configured)) + nstream===50+50 mb tcp
but for 2 chains +extension channel is not best... i think because no good Tx/rx CCQ - 80-90 %.

i was make a big mistake.... after succesfull test "on the table"( 200 Mbs wow!)) today i bring it to working link for replace nstream dual.(50+ 50 mbps)..distance 3 km.. 5G....2 antennas with differente polarisation... no noise in air.... link working perfect 2 minutes..( 270 HT/270 HT)/...

i was make a big mistake.... after succesfull test "on the table"( 200 Mbs wow!)) today i bring it to working link for replace nstream dual.(50+ 50 mbps)..distance 3 km.. 5G....2 antennas with differente polarisation... no noise in air.... link working perfect 2 minutes..( 270 HT/270 HT)//...