Community discussions

MUM Europe 2020

Search found 44 matches

by poli5681
Tue Jul 07, 2015 12:28 pm
Forum: General
Topic: HOTSPOT FILTER RULES add themself forcely
Replies: 3
Views: 830

Re: HOTSPOT FILTER RULES add themself forcely

hi every one when you setup any hotspot server you will find the filter rules shown in the image down ..these rules add themself forcely and autmaticaly even if you reboot the router board ....why ? , how can i remov them terminally ? thank you very much http://i.imgur.com/S3un8Jl.png You can´t. Th...
by poli5681
Sun May 25, 2014 6:21 pm
Forum: General
Topic: PCQ - Per IP
Replies: 6
Views: 1154

Re: PCQ - Per IP

Hi,

You´re most probably using the wrong classifier (src/dst swapped) for your queue.
Try to swap the classifiers, or post you config.
by poli5681
Wed May 07, 2014 6:39 pm
Forum: General
Topic: v6.12 released
Replies: 237
Views: 58178

Re: v6.12 released

It looks like wireless "tx-power-mode=card-rates" is not supported anymore... however, the command still exists. Does anyone know why? P.S. Not sure if it's from v6.12 or before, since I upgraded from v6.0... Same here.. isn't Card Rates better than All rates Fixed mode? i don't think it was intend...
by poli5681
Tue Jan 15, 2013 10:49 am
Forum: General
Topic: netinstall under ubuntu
Replies: 4
Views: 2170

Re: netinstall under ubuntu

Hello,

Wine lacks permissions to bind ports <1000 for security reasons; at least in my case on OpenSuse.
I got the same error till i ran "setcap cap_net_bind_service+eip /usr/bin/wine-preloader"; Maybe, do the same for "/usr/bin/wineserver".
You must have "libcap-progs" installed.

Martin
by poli5681
Wed Dec 05, 2012 2:11 pm
Forum: RouterBOARD hardware
Topic: RB800 Operating temperature...
Replies: 11
Views: 1724

Re: RB800 Operating temperature...

As far as i remember there was a hardware bug on the early RB800s, which led to incorrect temperature readings. We currently still have 2 of them running, without any problems so far but with ridiculous temperature readings. Soon after the issue was fixed; Still have one RB-800 here with a temporary...
by poli5681
Fri Nov 16, 2012 10:49 am
Forum: RouterBOARD hardware
Topic: CCR1036 vs Other vendors
Replies: 7
Views: 5098

Re: CCR1036 vs Other vendors

We had a Cisco 3825 before, with 2 additional ethernet cards (ridiculous expensive) and memory extension for full-bgp;
But this one was not able to handle more than 400Mbits/s.
by poli5681
Fri Nov 16, 2012 10:41 am
Forum: RouterBOARD hardware
Topic: CCR1036 vs Other vendors
Replies: 7
Views: 5098

Re: CCR1036 vs Other vendors

I got an offer a while ago to replace our core router (because of higher bandwidth demand) with Cisco ASR 1002 and ASR-ESP (5Gbit/s); The specs are not really near the CCR, but it´s price is more than 20 times higher. Just a sidenote: We had to replace the router ealier than expected and did it with...
by poli5681
Thu Aug 30, 2012 1:56 pm
Forum: Beginner Basics
Topic: IP redirection but translated?
Replies: 4
Views: 945

Re: IP redirection but translated?

You could do this with NAT of course, but i wouldn´t recommend doing so. I´d let the router do the job by simply adding an IP to both interfaces (like you already did). Then add a static route to 10.202.100.0 for your clients somewhere (at the clients or at your default gw) and do the same for the p...
by poli5681
Mon Jul 23, 2012 2:58 pm
Forum: General
Topic: IPsec VPN encryption performance
Replies: 2
Views: 1626

Re: IPsec VPN encryption performance

Yes it does; But the biggest issue (at least in our case) was the hash-algorithm.
We got 3 times the throughput by switching from sha1 to md5.
Maybe this will help in your case too.
by poli5681
Wed May 23, 2012 2:38 pm
Forum: General
Topic: RB1100 is powerful enough to connect to 1 Gb/s and BGP?
Replies: 6
Views: 1267

Re: RB1100 is powerful enough to connect to 1 Gb/s and BGP?

Hi asterisco, We´re pushing ~400Mbit/s BGP through a RB1100AH with 50% max load; But without conntrack and therefore without firewalling - generally this costs a lot of resources... I´m guessing it should work flawlessly with RB1100AH X2; To be 100% safe you could go for a AS1000 Series (sorry Mikro...
by poli5681
Tue Dec 06, 2011 1:22 pm
Forum: General
Topic: IP issues
Replies: 7
Views: 1121

Re: IP issues

If you bridge the interfaces, there won´t be any routing in place; Why do you need the RB450 then? You could simply use the Cisco Switch alone. If you want the RB450 as a transparent packet filter, just remove both IPs on the Interfaces and assign an address on the bridge interface. Additionally you...
by poli5681
Mon Nov 28, 2011 1:56 pm
Forum: RouterBOARD hardware
Topic: Question on Ethernet Bypass Mode, RB1100
Replies: 8
Views: 11562

Re: Question on Ethernet Bypass Mode, RB1100

1. Yep
2. We´re using them as transparent QOS-System; Therefore we´re able to bypass the box in case something goes wrong...
3. No
4. Yep
5. I could; But simply said our 1100s is tranparent between our Network and the Customer Net. So switching to bypass simply disables QOS

Hope that helps.
by poli5681
Wed Nov 02, 2011 10:45 am
Forum: Wireless Networking
Topic: bridge-mode
Replies: 3
Views: 517

Re: bridge-mode

i see that this state is enabled what does it do cause i cannot find any information on it and it seems to have just popped up in the menu since i got a board with v5.0+ on it Thats Mikrotiks proprietary way of implemention bridging an wireless interfaces in station mode. Only works with Mikrotik A...
by poli5681
Tue Aug 09, 2011 1:01 pm
Forum: Beginner Basics
Topic: Simply limit bandwith for each user
Replies: 1
Views: 667

Re: Simply limit bandwith for each user

Have a look into PCQ; This should meet your requirements:

http://wiki.mikrotik.com/wiki/Manual:Queues_-_PCQ
by poli5681
Thu Jul 28, 2011 4:26 pm
Forum: Beginner Basics
Topic: Port forwarding issue :-) Getting crazy please help me !
Replies: 5
Views: 877

Re: Port forwarding issue :-) Getting crazy please help me !

Yes, i´d recommend setting the interface instead of the local IP in rule 10.

Anyway i just noticed, that your rule should work (according to the packet flow diagram in the wiki).
I just tried on my own and it works.

Does it work, if you remove your final drop rule (Nr. 11)?
by poli5681
Thu Jul 28, 2011 3:49 pm
Forum: Beginner Basics
Topic: Port forwarding issue :-) Getting crazy please help me !
Replies: 5
Views: 877

Re: Port forwarding issue :-) Getting crazy please help me !

Filtering is done before NAT; Meaning you have to use a filter-rule like this: 10 ;;; allow public services chain=forward action=accept protocol=tcp in-interface=ether1 dst-port=80,443 or 10 ;;; allow public services chain=forward action=accept protocol=tcp dst-address=YOUR-WAN-IP dst-port=80,443
by poli5681
Fri Jul 22, 2011 8:45 pm
Forum: Beginner Basics
Topic: no speed above 1.5MBPS for file transfer....
Replies: 7
Views: 1158

Re: no speed above 1.5MBPS for file transfer....

Do you see any errors or drops at the interface statistics?
by poli5681
Thu Jul 21, 2011 12:09 pm
Forum: Beginner Basics
Topic: no speed above 1.5MBPS for file transfer....
Replies: 7
Views: 1158

Re: no speed above 1.5MBPS for file transfer....

You dont´t need Level 4 for PTP Setup. Just set Mode "Bridge" on the first and Mode "station-bridge" on the other - no need for WDS.
http://wiki.mikrotik.com/wiki/Manual:Wi ... ion-bridge

Additionally you have to add a bridge and bind both wlan and ether interface.
by poli5681
Wed Jul 20, 2011 9:11 pm
Forum: Beginner Basics
Topic: no speed above 1.5MBPS for file transfer....
Replies: 7
Views: 1158

Re: no speed above 1.5MBPS for file transfer....

Hi saintofinternet, Usually there´s no need for VPLS on PTP Links anymore; RouterOS V5 has a native Bridge Mode without the speed tradeoff using WDS; Said that, you won´t get good results at you test setup with 22dbi antennas just a couple of feet away... It´s like staring into the sun. Ideal signal...
by poli5681
Thu Jul 14, 2011 3:55 pm
Forum: Beginner Basics
Topic: Mikrotik 3 WAN, 1 LAN - Open Ports
Replies: 7
Views: 7471

Re: Mikrotik 3 WAN, 1 LAN - Open Ports

Hi,

I presume you already opened the port at the firewall forwarding chain...

You have to add a "dstnat" Rule for your destination port 3389 at the NAT Tab and select action "dst-nat" and your internal IP as "to-address".
by poli5681
Tue Jul 12, 2011 12:36 pm
Forum: Beginner Basics
Topic: How to: RB1200, port 6-10 in same network
Replies: 7
Views: 4227

Re: How to: RB1200, port 6-10 in same network

No, its always better to use switching if possible, as long as you don´t need firewall rules etc. between the ports.
With switching enabled you always have wirespeed between the swiched ports;
Bridging takes some CPU-Power.
by poli5681
Tue Jul 12, 2011 12:19 pm
Forum: Beginner Basics
Topic: How to: RB1200, port 6-10 in same network
Replies: 7
Views: 4227

Re: How to: RB1200, port 6-10 in same network

Sorry Normis,

I thought it´s the same as with RB1100 - didn´t even check the product image :-)

Anyway astude you can do your setup by binding 6-10 and 2 to the same bridge.

Edit.: It might be a better idea to use eg. port 10 for internet uplink. Gives you 1 more port for switching...
by poli5681
Tue Jul 12, 2011 11:37 am
Forum: Beginner Basics
Topic: How to: RB1200, port 6-10 in same network
Replies: 7
Views: 4227

Re: How to: RB1200, port 6-10 in same network

Hi, RB1200 has 2 switch groups. 1st has ports 1-5; 2nd has 6-10. You can set 2-5 for switching (you did this already);Do the same for 6-10 and use port 6 as the master port. Now add a bridge and bind port 2 and 6; You won´t take advantage of the switch chip for traffic between group 1 and 2, but eve...
by poli5681
Sun Mar 27, 2011 2:23 pm
Forum: RouterBOARD hardware
Topic: RB-1100 Port problems, and performance problems
Replies: 61
Views: 19125

Re: RB-1100 Port problems, and performance problems

Can anyone confirm the resolution of these issues? Which version of ROS resolves the issue or is it not out yet? We have a RB1100 we have taken out of service and would like to use it again. Rick Yes, i have a device in production now, after some testing with 4.17; Problems with Port 11-13 are gone...
by poli5681
Sun Feb 06, 2011 2:42 pm
Forum: RouterBOARD hardware
Topic: RB1100 low bridging/shapping performance
Replies: 57
Views: 10400

Re: RB1100 low bridging/shapping performance

Maybe bridging ports 5 and 6, on different switch chips, would be even better?
Thank you RK; That might be even better.
I still have 1 RB1100 left to install; I´ll try and let you know my results.
by poli5681
Sat Feb 05, 2011 9:31 pm
Forum: RouterBOARD hardware
Topic: RB1100 low bridging/shapping performance
Replies: 57
Views: 10400

Re: RB1100 low bridging/shapping performance

Hello NetworkPro,

I´ve ROS 4.16 and BL2.29 on my last RB1100 and ROS 4.11 and BL2.27 on my first;
So i guess all versions in between are affected.
by poli5681
Sat Feb 05, 2011 9:15 pm
Forum: RouterBOARD hardware
Topic: RB1100 low bridging/shapping performance
Replies: 57
Views: 10400

Re: RB1100 low bridging/shapping performance

Hello mihaialdea, I had similar problems with bridging and queues on my 1100s; I bridged Port 11-12 , enabled piping through fw, and added mangle rules and a complex queue tree for interface 12: The result was a more or less completely unresponsible RB - the interfaces showed only a few Mbps of data...
by poli5681
Mon Oct 11, 2010 10:12 am
Forum: RouterBOARD hardware
Topic: Total gn00b
Replies: 2
Views: 820

Re: Total gn00b

Hi, You have to add a network connection to the connection manager with manual IP and Gateway; Ubuntu disables the interface if it can´t find a DHCP Server and you don´t have a manual configuration. Default configured IP on RBs is 192.168.88.1; But it doesn´t really matter, because WinBox will find ...
by poli5681
Wed Sep 29, 2010 10:02 am
Forum: RouterBOARD hardware
Topic: Routerboard under high ambient temperature
Replies: 3
Views: 838

Re: Routerboard under high ambient temperature

Dear Martin, I´ve a few alu cases with RB800s installed here in Austria and the temperature is rising up 20C+ when exposed to direct sunlight - however they don´t fail. I guess this will be much more of a problem in the Gulf region. But i think RB800s are even more affected by high temperatures, due...
by poli5681
Mon Sep 27, 2010 9:21 pm
Forum: RouterBOARD hardware
Topic: Routerboard under high ambient temperature
Replies: 3
Views: 838

Routerboard under high ambient temperature

Hi,

Anybody here using MT boards under high ambient temperatures? I´ve to build a few links in the UAE and i´m concerned about the high ambient temperatures and sun.

I usually prefer to mount them outdoors with aluminium cases, of course here in austria...;
Will they just work, or die?

Thanks.
by poli5681
Sat Aug 14, 2010 11:22 am
Forum: RouterBOARD hardware
Topic: Do you need to use both antenna connectors?
Replies: 5
Views: 1196

Re: Do you need to use both antenna connectors?

Yes - exactly.
You may find many threads here discussing the difference of such setups;
So you´ll get an idea what to expect of each one.
by poli5681
Fri Aug 13, 2010 11:24 pm
Forum: RouterBOARD hardware
Topic: Do you need to use both antenna connectors?
Replies: 5
Views: 1196

Re: Do you need to use both antenna connectors?

The N cards have MIMO technology; This gives you better signal and higher data rates.
http://en.wikipedia.org/wiki/MIMO
But you´re fine with a single chain setup, even with N.
by poli5681
Tue Aug 03, 2010 10:49 am
Forum: RouterBOARD hardware
Topic: RB1100 Port 11/12 issues
Replies: 6
Views: 1302

Re: RB1100 Port 11/12 issues

Normis had posted that 4.11 would fix this issue. However, there is nothing in the 4.11 release notes to indicate that this issue has actually been fixed. Has anyone downloaded 4.11 to see if it addresses this issue? Yes, i upgraded to 4.11; this fixed an issue with ports still showing traffic afte...
by poli5681
Mon Aug 02, 2010 4:14 pm
Forum: RouterBOARD hardware
Topic: RB1100 Port 11/12 issues
Replies: 6
Views: 1302

Re: RB1100 Port 11/12 issues

http://forum.mikrotik.com/viewtopic.php?f=3&t=43212&hilit=Rb1100 Related? Thank you, maybe it is... Strangely it doesn´t happen, if i disable queue on these ports. The ports were up and running for about a week (pushing ~8Mbit of traffic), before i enabled the queue tree today. So i had no issues b...
by poli5681
Mon Aug 02, 2010 3:59 pm
Forum: RouterBOARD hardware
Topic: RB1100 Port 11/12 issues
Replies: 6
Views: 1302

RB1100 Port 11/12 issues

Hello everyone, I have the following issues on port 11 and 12: I´ve bridged both ports with a software bridge (hardware bypass mode is off). I enabled the "Use IP Firewall" feature on the bridge, added a few mangle rules and a queue tree. Immediately after enabling the queue the ports go on/off ever...
by poli5681
Tue Jun 08, 2010 2:15 pm
Forum: RouterBOARD hardware
Topic: Recomended hardware? 300m line of sight, perfect quality
Replies: 2
Views: 674

Re: Recomended hardware? 300m line of sight, perfect quality

Hi, If you need more than 100Mbit with POE your only option is RB800 with n-Wireless and a good dual-pol antenna. This is the only board to support 1Gbit Interfaces with ieee802.11af POE. Your costs might be a bit higher than 800€, but believe me, its worth. If 100Mbit are enough for you, RB433AH is...
by poli5681
Tue Apr 13, 2010 12:28 pm
Forum: RouterBOARD hardware
Topic: RB800 Dropping Ethernet Link
Replies: 9
Views: 1815

Re: RB800 Dropping Ethernet Link

Thank you. The link was up with 1Gbs and is now 100Mbit without autoneg and stable - didn´t see this. The routerboards IF was set to 100Mbits but synced with 1Gbs. Does the speed setting do anything, when autoneg is enabled? I´ll reenable autoneg, set the speed to 1Gbs (if that does anything) and wa...
by poli5681
Tue Apr 13, 2010 11:31 am
Forum: RouterBOARD hardware
Topic: RB800 Dropping Ethernet Link
Replies: 9
Views: 1815

Re: RB800 Dropping Ethernet Link

I have exactly the same setup; and of course the same problems. My RB800 is powered with POE (48V over datalines) and connected via 1Gbs link to a Cisco 3800. Strangely our link is sometimes up for more than 12 hours and then suddenly drops and comes back seconds later. I´ve disabled autoneg yesterd...
by poli5681
Thu Jul 23, 2009 6:52 pm
Forum: Wireless Networking
Topic: HWMP+ not working as expected
Replies: 9
Views: 1769

Re: HWMP+ not working as expected

Yes, i think thats exactly what happens. But i can't imagine how that loop is produced. I only have wireless devices connected at the moment - the 7APs and one wireless client. No additional bridges with (r)stp in place. @DogHead: Yes you're right. It works perfectly as long as i connect per IP not ...
by poli5681
Wed Jul 22, 2009 8:28 pm
Forum: Wireless Networking
Topic: HWMP+ not working as expected
Replies: 9
Views: 1769

Re: HWMP+ not working as expected

Thank you; It's good to see i'm not alone; and that i've nothing misconfigured. Hope it will be fixed soon...; i need it up in some way before september. BTW.: It seems WINBOX interferes with HWMP+ somehow. Whenever i connect to any of the devices with Winbox the network crashes. I can reproduce thi...
by poli5681
Wed Jul 22, 2009 6:11 pm
Forum: Wireless Networking
Topic: HWMP+ not working as expected
Replies: 9
Views: 1769

HWMP+ not working as expected

Hello, We tried to build a mesh system with 7 AP's; First we used the simple approach with WDS and rtsp - it worked, but the performance was bad. Then we tried using HWMP+ and it seemed to perform much better. But after a few minutes the latency to all devices goes up and up. A few seconds later non...
by poli5681
Sat Jul 18, 2009 4:53 pm
Forum: RouterBOARD hardware
Topic: Pl guide me on the basic set up
Replies: 6
Views: 1263

Re: Pl guide me on the basic set up

Hello, You don need to use routes for this. Just configure one device as ap-bridge (or simply bridge) and the other as "station wds". Add a bridge and add the ether and wlan ports to that bridge on both devices. As long as your PCs are in the same subnet you should be able to do bandwidth tests, or ...
by poli5681
Fri Jul 03, 2009 12:11 pm
Forum: General
Topic: R52n and 802.11n devices
Replies: 15
Views: 7292

Re: R52n and 802.11n devices

Hello to everyone, this is my first post... Same problem here;I use the R52n card with RB493. I can't connect in pure-n mode with devices other than Mikrotik. I've tried intensively yesterday with n-devices by ASUS, Linksys and Edimax. They connect perfectly in b/g/n (but with 54Mbit max - G-mode) o...