Community discussions

Search found 230 matches

by DannyZ
Wed Feb 16, 2011 7:32 pm
Forum: Wireless Networking
Topic: Any ideas about this issue?
Replies: 10
Views: 1729

Re: Any ideas about this issue?

could it be low FZ? There is another CPE connected to same AP - runs cheap 29dBi e-zy.net diecast grid, only that CPE have ~30000kbps p throughput and its ~7km from AP. Signal ~-67/-67 Tx/Rx and 100% CCQ. But if i start download something with max speed (~0.9MB/s), that 29dBi CPE P Throughput goes d...
by DannyZ
Wed Feb 16, 2011 3:29 pm
Forum: Wireless Networking
Topic: Any ideas about this issue?
Replies: 10
Views: 1729

Re: Any ideas about this issue?

Dish setup runs RB532A with ROS 4.15 and Flags: X - disabled # NAME VERSION SCHEDULED 0 dhcp 4.15 1 system 4.15 2 wireless 4.15 3 advanced-tools 4.15 4 calea 4.15 5 routerboard 4.15 Flat setup runs RB411 with ROS 4.5 and Flags: X - disabled # NAME VERSION SCHEDULED 0 routeros-mipsbe 4.5 1 system 4.5...
by DannyZ
Sat Feb 12, 2011 8:22 pm
Forum: Wireless Networking
Topic: Any ideas about this issue?
Replies: 10
Views: 1729

Re: Any ideas about this issue?

currently cant set panel instead of dish. Current -75dBi and P Throughput is 13000Kbps (above). thinking to order XR5.
by DannyZ
Sat Feb 12, 2011 2:01 pm
Forum: Wireless Networking
Topic: Any ideas about this issue?
Replies: 10
Views: 1729

Re: Any ideas about this issue?

I did alingment, there shouldnt be problem. AP uses R52 as well. What u mean by using panel? Panel is connected to same AP only distance is ~5km. Only one im not quite sure is FZ. :) AP ir 43m high, 30dBi parabolic dish ~7m.
by DannyZ
Fri Feb 11, 2011 3:39 pm
Forum: Wireless Networking
Topic: RB133c as a repeater on exisiting wireless network
Replies: 1
Views: 473

Re: RB133c as a repeater on exisiting wireless network

Im not sure, but RB133C doesnt support AP-Bridge mode - so it cant be used as u want it. however u can read more about that here
by DannyZ
Fri Feb 11, 2011 3:31 pm
Forum: Wireless Networking
Topic: Any ideas about this issue?
Replies: 10
Views: 1729

Any ideas about this issue?

Hello. Still cant figure what is causing this issue. I have dozens of long distance connections running perfect. This one is 10km away with good LOS. AP 90° 17dBi sectoral antenna, CPE side A (that who has low PThroughput) 30dBi parabolic dish (Made by MT with new type feed). CPE side B 22dBi flat p...
by DannyZ
Thu Dec 30, 2010 12:08 am
Forum: Wireless Networking
Topic: Wireless problem!
Replies: 10
Views: 1132

Re: Wireless problem!

yes u can use your 5Ghz antennas for point to point connection from building A to building B without any problems. 5Ghz has less interference, only u need clear LOS.
by DannyZ
Mon Dec 27, 2010 6:29 pm
Forum: Wireless Networking
Topic: Wireless problem!
Replies: 10
Views: 1132

Re: Wireless problem!

:D i think your laptop wlan card doesnt know such a standart as 802.11n, and thats your problem. select AP band to 2.4Ghz b/g and i think u should be good..
by DannyZ
Thu Dec 23, 2010 10:34 pm
Forum: Wireless Networking
Topic: Wireless problem!
Replies: 10
Views: 1132

Re: Wireless problem!

R will be showed up only when someone will be connected to your antennas. So try that, then report.
by DannyZ
Thu Dec 23, 2010 7:54 pm
Forum: Wireless Networking
Topic: Upgrade issue with 1 cpe?
Replies: 4
Views: 779

Re: Upgrade issue with 1 cpe?

U need all thos packages? :o install only those packages u need, and dont install nv2 pkg.
by DannyZ
Thu Dec 23, 2010 7:02 pm
Forum: General
Topic: RouterOS 5.0rc5 bandwitch test
Replies: 1
Views: 1728

Re: RouterOS 5.0rc5 bandwitch test

what psu u use?
by DannyZ
Thu Dec 23, 2010 6:45 pm
Forum: Wireless Networking
Topic: Upgrade issue with 1 cpe?
Replies: 4
Views: 779

Re: Upgrade issue with 1 cpe?

Did u try to uninstall wireless-nv2 package in Package list and install regular Wireless-4.16 package?
by DannyZ
Mon Dec 20, 2010 8:02 pm
Forum: General
Topic: utorrents 2.2 l7 mt 5 b4
Replies: 5
Views: 2043

Re: utorrents 2.2 l7 mt 5 b4

Welcome
by DannyZ
Mon Dec 20, 2010 2:25 pm
Forum: Forwarding Protocols
Topic: Hotspot
Replies: 3
Views: 707

Re: Hotspot

by DannyZ
Mon Dec 20, 2010 1:50 pm
Forum: General
Topic: utorrents 2.2 l7 mt 5 b4
Replies: 5
Views: 2043

Re: utorrents 2.2 l7 mt 5 b4

Before say no - try it.
by DannyZ
Mon Dec 20, 2010 12:56 am
Forum: General
Topic: utorrents 2.2 l7 mt 5 b4
Replies: 5
Views: 2043

Re: utorrents 2.2 l7 mt 5 b4

Dont know about you but i use 3 Layer 7 protocols to limit (give lower priorety) 1. Bittorent: ^(\13bittorrent protocol|azver\01$|get/scrape\?info_hash=)|d1:ad2:id20:|\08'7P\)[RP] 2: EDonkey: ^[\C5\D4\E3-\E5].\?.\?.\?.\?([\01\02\05\14\15\16\18\19\1A\1B\1C !234568@ABCFGHIJKLMNOPQRSTUVWX[`\81\82\90\91...
by DannyZ
Sun Dec 19, 2010 10:31 pm
Forum: General
Topic: QoS and latency
Replies: 3
Views: 1233

Re: QoS and latency

Its important if u have lot of clients who downloads large amount of data. Im running 18 mangle rules and queue tree for Qos and everything works nice. Users now can play online games with normal latency and enjoy online media (ect. youtube, soundcloud ..) without laags. But Anyway its not the same ...
by DannyZ
Sat Dec 18, 2010 8:41 pm
Forum: Forwarding Protocols
Topic: Hotspot
Replies: 3
Views: 707

Re: Hotspot

Its called Bypass Mikrotik Hotspot. ;) by using some hack tricks
by DannyZ
Sat Dec 18, 2010 6:14 pm
Forum: General
Topic: [SOLVED] Upgrade from 2.9.30 to 3.30
Replies: 7
Views: 1376

Re: [SOLVED] Upgrade from 2.9.30 to 3.30

welcome.. :)
by DannyZ
Sat Dec 18, 2010 4:26 pm
Forum: General
Topic: [SOLVED] Upgrade from 2.9.30 to 3.30
Replies: 7
Views: 1376

Re: Upgrade from 2.9.30 to 3.30

Yes - Downgrade is possable by using /system package downgrade
I gues u need to select gateway in route list and thats all.
by DannyZ
Sat Dec 18, 2010 1:41 pm
Forum: General
Topic: [SOLVED] Upgrade from 2.9.30 to 3.30
Replies: 7
Views: 1376

Re: Upgrade from 2.9.30 to 3.30

Yes u will be able to use 2.9.30 backup in 3.30.
No u dont need to buy new key. Just after u will install 3.30 got to System>License and press Update License Key. After update bootloader
[admin@MikroTik] > system routerboard upgrade
Then u're good to go for 4.15 ROS
by DannyZ
Sat Dec 18, 2010 12:58 pm
Forum: General
Topic: [SOLVED] Upgrade from 2.9.30 to 3.30
Replies: 7
Views: 1376

Re: Upgrade from 2.9.30 to 3.30

No need to worry, Just do backup in case something will go wrong. Download ROS 3.30 and u're good to go (have same boards). After 3.30 u can upgrade 4.15 (Last stable ROS) and u should not lost any settings. Dont forget to update KEY before run 4.15 upgrade. Same with Bootloader (Latest for RB532 2....
by DannyZ
Fri Dec 17, 2010 5:43 pm
Forum: General
Topic: old router os version
Replies: 2
Views: 507

Re: old router os version

u mean how you can install it? Upload all needed packages to <File> section by using drag and drop. Then open terminal ant type: system reboot Y
by DannyZ
Wed Dec 15, 2010 8:01 pm
Forum: Wireless Networking
Topic: Link distruction
Replies: 1
Views: 455

Link distruction

Do i destruct link when connection to AP (Shown in image)? Image
by DannyZ
Sat Dec 11, 2010 2:02 am
Forum: Scripting
Topic: Signal Strenght Script
Replies: 0
Views: 527

Signal Strenght Script

Can someone edit this script for Signal Strenght (dBm)? Then higher is signal, then more LEDs blink or then better is signal then more LEDs light up. :) Please :global if-snr [ /interface wireless registration-table get [/interface wireless registration-table find] signal-to-noise ] :if (($if-snr > ...
by DannyZ
Tue Dec 07, 2010 9:27 pm
Forum: RouterBOARD hardware
Topic: 4.9GHz on R52Hn?
Replies: 6
Views: 1203

Re: 4.9GHz on R52Hn?

Nop, coz its public safety frequency (police, fire dep, emerency ect.)
by DannyZ
Tue Dec 07, 2010 7:10 pm
Forum: The User Manager
Topic: Starting a hotspot with a routerboard only...oh yea
Replies: 1
Views: 827

Re: Starting a hotspot with a routerboard only...oh yea

Yes - Level 4 is supported and all u need to know is listed down here
by DannyZ
Fri Dec 03, 2010 3:09 pm
Forum: General
Topic: RB532 issue with ROS 5.0xRC
Replies: 1
Views: 993

RB532 issue with ROS 5.0xRC

Facing some wierd issue with RB532 + Compex WLM54AGP A6 (Atheros AR5413) cards. Now running ROS 4.13 and have no problem. But with ROS 5.05RC get very high packet loss and disconnecting form AP.. :shock: No differece 2.4Ghz or 5Ghz, same on both cards.

P.S. FW up to date (2.18)
by DannyZ
Fri Nov 26, 2010 1:23 am
Forum: RouterBOARD hardware
Topic: Growing out of RB433AH? RB for border router.
Replies: 7
Views: 2390

Re: Growing out of RB433AH? RB for border router.

dont think he needs rb800, coz rb433ah can run 800Mhz as well
[Basnet@MikroTik] > system routerboard settings set cpu-frequency=800
by DannyZ
Mon Nov 22, 2010 7:23 pm
Forum: RouterBOARD hardware
Topic: Growing out of RB433AH? RB for border router.
Replies: 7
Views: 2390

Re: Growing out of RB433AH? RB for border router.

I gues nstreme2 cause cpu load. there nothing u can do, except replacing rb to powerpc
by DannyZ
Mon Nov 22, 2010 4:47 pm
Forum: General
Topic: Very High Packet Loss.
Replies: 6
Views: 1128

Re: Very High Packet Loss.

No mate - small willage romance. When i make snooper i get:

Image

gues thos between 2427 are eco.
by DannyZ
Mon Nov 22, 2010 3:57 pm
Forum: General
Topic: Very High Packet Loss.
Replies: 6
Views: 1128

Re: Very High Packet Loss.

Ping is from Latvia to UK.
From CPE to AP (~4km)
Image
by DannyZ
Mon Nov 22, 2010 3:38 pm
Forum: General
Topic: Very High Packet Loss.
Replies: 6
Views: 1128

Re: Very High Packet Loss.

Alignment is fine, and i try to exchange radio card - no differene. Antenna mounted prperly and doesnt move even in strong wind. Currently have: http://fotohost.lv/images/7o3kctvnfb1dm2k8j640.jpg So, i dont think its my CPE issue. Does AP (ptmp) must be fixed Tx rates on one value or it makes no dif...
by DannyZ
Sun Nov 21, 2010 3:11 pm
Forum: Beginner Basics
Topic: Buy RB 1100 Central Europe
Replies: 1
Views: 580

Re: Buy RB 1100 Central Europe

http://www.router.lv/product/73/lv/RB1100/ (Latvia local distributor) Price ~277Euro +VAT 21% (58.18Euro) per unit + Shipping (depends on logistic service)
Or wait few days and order it fom wifi stock http://www.wifi-stock.com/details/mikrotik_rb1100.html
by DannyZ
Sat Nov 20, 2010 8:57 pm
Forum: General
Topic: Very High Packet Loss.
Replies: 6
Views: 1128

Very High Packet Loss.

Have some problem, but dont know what cause it. Daytime my cpe connection to p2mp is going down and have 100% packet loss to AP (~25/30% Tx/Rx). Now everything is okey (~90/95% Tx/Rx). Ap is MT with 5Ghz backhaul and 2.4/5Ghz omni (RB433UAH/3xR52 @ default Tx rates). Facing this issue 3th day. No ot...
by DannyZ
Sat Nov 13, 2010 1:13 pm
Forum: RouterBOARD hardware
Topic: WHats wrong with P troughput?
Replies: 2
Views: 920

Re: WHats wrong with P troughput?

CCQ was 100% day before and now again its 100%. Maybe u're right about interference. As far i checked - noone was on same band. Its 5Ghz bandwidth.
by DannyZ
Thu Nov 11, 2010 8:28 pm
Forum: RouterBOARD hardware
Topic: WHats wrong with P troughput?
Replies: 2
Views: 920

WHats wrong with P troughput?

Today faces some weard problem with RB800. Why P-Troughtput is so low? Its major problem, coz true that RB800 i have connected lot of clients. :(

Image
by DannyZ
Thu Nov 11, 2010 6:40 pm
Forum: General
Topic: Feature requests
Replies: 1163
Views: 213059

Re: Feature requests

How about something like Ubicom Stream Engine?
by DannyZ
Mon Nov 08, 2010 4:26 pm
Forum: General
Topic: Please bring back the RB600.
Replies: 1
Views: 534

Re: Please bring back the RB600.

Sorry - can't help with your demand. But did u research webshops?i have found em in stock in EU.
by DannyZ
Mon Nov 08, 2010 1:20 am
Forum: Wireless Networking
Topic: rb433ah and 4 radio
Replies: 1
Views: 569

Re: rb433ah and 4 radio

its not possable as far i know, coz RB433AH has only 3miniPCI slots without no daughter board support.
by DannyZ
Sat Nov 06, 2010 9:18 pm
Forum: Beginner Basics
Topic: Block P2P traffic
Replies: 4
Views: 1234

Re: Block P2P traffic

i need to do that on all routers which ar involved in bridge?
My CPE+Hotspot <------> AP+WDS(bridged) <------> AP+WDS(bridged) <------> AP+WDS(bridged) <------> ISP
Or better is marking packets by using mangle to another gateway? (Local ping is acceptable, but outboard is way too high)
by DannyZ
Sat Nov 06, 2010 6:50 pm
Forum: Beginner Basics
Topic: Block P2P traffic
Replies: 4
Views: 1234

Re: Block P2P traffic

then any ideas how to improve Qos? Main reason is online gaming. If users are downloading torrents (~18Mb/s) and i recive latency >300ms. Is there anything i can do to improve ping?
by DannyZ
Sat Nov 06, 2010 6:09 pm
Forum: Beginner Basics
Topic: Block P2P traffic
Replies: 4
Views: 1234

Block P2P traffic

Hi all. I know this was discussed many times. But still cant block P2P traffic. Tryed /ip firewall filter add chain=forward p2p=all-p2p action=drop.. not working. Can someone give me layer7 guide to block p2p traffic? :(
by DannyZ
Sat Nov 06, 2010 3:42 pm
Forum: RouterBOARD hardware
Topic: plz help
Replies: 4
Views: 919

Re: plz help

You cant connect or just browser cant see it connected?
by DannyZ
Fri Nov 05, 2010 11:43 pm
Forum: RouterBOARD hardware
Topic: RB800 and RB616 Problem
Replies: 1
Views: 740

Re: RB800 and RB616 Problem

What PSU hi uses?
by DannyZ
Fri Nov 05, 2010 3:26 pm
Forum: RouterBOARD hardware
Topic: plz help
Replies: 4
Views: 919

Re: plz help

Try to clear cache and add firewall exceptions and save MAC address login.
by DannyZ
Thu Nov 04, 2010 2:35 pm
Forum: Wireless Networking
Topic: wireless distance
Replies: 1
Views: 750

Re: wireless distance

All depends on LOS (Line of sight), antennas, radio cards and frequency. i've rb433uah with r52+29dBi parabolic dishes and link between em is over 12km and still have CCQ 100% (-66/-68).
by DannyZ
Tue Nov 02, 2010 3:42 pm
Forum: Wireless Networking
Topic: Speed Issue
Replies: 2
Views: 685

Re: Speed Issue

could you post the config? 1 R name="Wlan1" mtu=1500 mac-address=00:13:46:98:23:68 arp=enabled interface-type=Atheros AR5413 mode=station ssid="WaterTower" frequency=2427 band=2ghz-b/g channel-width=20mhz scan-list=default wireless-protocol=unspecified antenna-mode=ant-a wds-mode=disabled wds-defau...
by DannyZ
Sat Oct 30, 2010 8:49 pm
Forum: Beginner Basics
Topic: what is periodic calibration?
Replies: 3
Views: 2198

Re: what is periodic calibration?

It is used for ACK timeout setting, mikrotik tries from time to time to chet and set ACK timeout, it should be used on p2p links, and can be turned off on APBRIDGE mode if you use that mode for connecting clients to antenna.
by DannyZ
Fri Oct 29, 2010 4:18 pm
Forum: Wireless Networking
Topic: Speed Issue
Replies: 2
Views: 685

Speed Issue

Hi all. Have some weard situation. Instal 2.4Ghz link over 4km. Everything would be okey, only speed is not i was expected. I assume speed should be >25Mbps but nop - all i get on Rx (UDP) is ~18Mbps and ~8Mbps on Tx. Any ideas? Even when AP is idle (noone, except me, connected) and signal is 54/54M...
by DannyZ
Thu Oct 28, 2010 7:58 pm
Forum: RouterBOARD hardware
Topic: Cable soldering
Replies: 2
Views: 848

Re: Cable soldering

Sorry - get n-male connector, so connected antena as it should be.
by DannyZ
Thu Oct 28, 2010 2:11 pm
Forum: Beginner Basics
Topic: P2P Shaping
Replies: 2
Views: 1866

Re: P2P Shaping

by DannyZ
Wed Oct 27, 2010 11:11 pm
Forum: RouterBOARD hardware
Topic: Cable soldering
Replies: 2
Views: 848

Cable soldering

Hi all. Have funny question, is it possible to solder two LMR400 cables together? (have antenna with cutted LMR400 cable and dont have NFemale connetor)
by DannyZ
Mon Oct 25, 2010 11:27 pm
Forum: RouterBOARD hardware
Topic: High Power miniPCI radio Cards for RB433AH
Replies: 9
Views: 3204

Re: High Power miniPCI radio Cards for RB433AH

It will not help u to push signal thru the trees. I would suggest higher point to mount.
by DannyZ
Fri Feb 19, 2010 3:29 am
Forum: General
Topic: Default the MT OS?
Replies: 2
Views: 412

Re: Default the MT OS?

Sure.

Type this @ terminal: system reset-configuration
by DannyZ
Sat Jan 23, 2010 7:06 pm
Forum: General
Topic: IP Service Port
Replies: 6
Views: 1839

Re: IP Service Port

ROS 4.5 doesn't have gre(47). U wanna use pptp over gre (47) port?
by DannyZ
Sat Jan 23, 2010 4:12 pm
Forum: General
Topic: Pls Help RB433,unable to access user mananager
Replies: 7
Views: 811

Re: Pls Help RB433,unable to access user mananager

Sorry about firewall filter rules - don't need them.
There can be many reasons. First of all, are you sure about your setup? My suggestion will be read this http://wiki.mikrotik.com/wiki/User_Manager or wait for more advanced answer. Sorry
by DannyZ
Fri Jan 22, 2010 12:16 am
Forum: General
Topic: Pls Help RB433,unable to access user mananager
Replies: 7
Views: 811

Re: Pls Help RB433,unable to access user mananager

from terminal > ip firewall filter print
by DannyZ
Thu Jan 21, 2010 7:47 pm
Forum: General
Topic: Pls Help RB433,unable to access user mananager
Replies: 7
Views: 811

Re: Pls Help RB433,unable to access user mananager

Had similar problem. Post your F/W filter rules.
by DannyZ
Thu Jan 21, 2010 7:44 pm
Forum: Beginner Basics
Topic: Some sites do not open
Replies: 3
Views: 837

Re: Some sites do not open

how about Win+R>cmd>ipconfig flushdns ? and or @terminal /ip dns cache flush
by DannyZ
Tue Jan 19, 2010 3:23 pm
Forum: RouterBOARD hardware
Topic: Hot new Mikrotik Radio Card - R52Hn
Replies: 66
Views: 16852

Re: Hot new Mikrotik Radio Card - R52Hn

Nice.. can't wait it will be available at balticnetworks. :)
by DannyZ
Sun Jan 17, 2010 7:54 pm
Forum: Beginner Basics
Topic: Can't Access Router.
Replies: 2
Views: 554

Re: Can't Access Router.

Okey, will try it tomorrow. Thanks a lot.
by DannyZ
Sun Jan 17, 2010 4:09 pm
Forum: Beginner Basics
Topic: Can't Access Router.
Replies: 2
Views: 554

Can't Access Router.

Hi. Have some problem with access to router. After i set firewall rules: 0 ;;; Established Connections chain=input action=accept connection-state=established 1 ;;; Related Connections chain=input action=accept connection-state=related 2 ;;; Log Invalid Connections chain=input action=log connection-s...
by DannyZ
Wed Jan 13, 2010 10:10 pm
Forum: Forwarding Protocols
Topic: Redirect separate IP to other autonomous system (AS)
Replies: 6
Views: 1784

Re: Redirect separate IP to other autonomous system (AS)

Im dumm and/or stupid, can you drop terminal command to to that?
by DannyZ
Wed Jan 13, 2010 9:47 pm
Forum: Wireless Networking
Topic: Not having a G mode
Replies: 8
Views: 1033

Re: Not having a G mode

How about your Tx/Rx Rates, Tx/Rx CCQ,ack timeout on both ends and P Troughput at CPE side?
by DannyZ
Wed Jan 13, 2010 9:10 pm
Forum: Forwarding Protocols
Topic: Redirect separate IP to other autonomous system (AS)
Replies: 6
Views: 1784

Re: Redirect separate IP to other autonomous system (AS)

And again i have some questions about L3VPN (VRF). So Here is full network layout of my Networks. I have 2 internet connection. 1th (87.246.130.215) has high foreign traffic capacity (lower latency), But 2nd (212.70.183.44) has very low foreign traffic capacity (~10Mbps over 100 costumers). So i wan...
by DannyZ
Wed Jan 13, 2010 6:46 pm
Forum: Wireless Networking
Topic: Data from unknown device
Replies: 7
Views: 5563

Re: Data from unknown device

<DEV>: data from unknown device <MAC>, sent deauth [(XXX events suppressed, YYY deauths suppressed)] Data frame from unknown device (read - not registered to this AP) with mac address <MAC> received, AP sent deauthentication frame to it (as per 802.11). XXX is number of events that are not logged so...
by DannyZ
Wed Jan 13, 2010 3:14 pm
Forum: Wireless Networking
Topic: Not having a G mode
Replies: 8
Views: 1033

Re: Not having a G mode

802.11B is a half duplex protocol, it can send or revive, but not both at the same time.
by DannyZ
Wed Jan 13, 2010 2:52 am
Forum: Wireless Networking
Topic: 11n channel width support.
Replies: 6
Views: 1385

Re: 11n channel width support.

How about reading this http://en.wikipedia.org/wiki/IEEE_802.1 ... _in_2.4GHz and u will get answers on your question.

Nop, there is no support to 5 and 10mhz channel width because it's not possable. To you know meaning of nonoverlapping independent channels?
by DannyZ
Wed Jan 13, 2010 2:11 am
Forum: Wireless Networking
Topic: XR3 Freezing?
Replies: 29
Views: 4192

Re: XR3 Freezing?

omg 28 posts and 3/4 from them is yours. Maybe use edit? And if it matters, u are running XR3 (Ubiquiti) radio, so worm it up or ask about it Mike.
by DannyZ
Tue Jan 12, 2010 4:58 pm
Forum: Wireless Networking
Topic: DISCONNECTING
Replies: 1
Views: 457

Re: DISCONNECTING

AP is disconnecting or CPE? If CPE, it's normal when CPE has cranky signal strenght. I have same problem with one CPE.
by DannyZ
Tue Jan 12, 2010 4:55 pm
Forum: Wireless Networking
Topic: Not having a G mode
Replies: 8
Views: 1033

Re: Not having a G mode

InoX B speed depends on duplex mode.
by DannyZ
Tue Jan 12, 2010 3:23 pm
Forum: Beginner Basics
Topic: Need help with IP subnet RB433AH
Replies: 6
Views: 1311

Re: Need help with IP subnet RB433AH

Can you tell more clearly what u are up to? U wanna set Ether1 ip range 10.10.10.178/29 (10.10.10.177 - 10.10.10.182)? and split it between ether2 and ether3? :D
by DannyZ
Tue Jan 12, 2010 2:15 pm
Forum: Wireless Networking
Topic: Not having a G mode
Replies: 8
Views: 1033

Re: Not having a G mode

Check AP Data Rates.
by DannyZ
Tue Jan 12, 2010 2:10 pm
Forum: Beginner Basics
Topic: Need help with IP subnet RB433AH
Replies: 6
Views: 1311

Re: Need help with IP subnet RB433AH

:D duhh.. Use subnet calculator i u don't know how to calculate them. subnet calculator
by DannyZ
Tue Jan 12, 2010 1:51 pm
Forum: General
Topic: Low disk space
Replies: 7
Views: 2406

Re: Low disk space

Dude + logs weighs lot more i think.
by DannyZ
Tue Jan 12, 2010 1:49 pm
Forum: Wireless Networking
Topic: 2.4 ghz links, -60 signal, turbo mode, 13 mbps udp speed
Replies: 21
Views: 2776

Re: 2.4 ghz links, -60 signal, turbo mode, 13 mbps udp speed

I know, thats because u have no clear view from point A to point B. I you have 2.4Ghz link and few branches on the way, it will not affect on your link so much as it will be on 5Ghz.
by DannyZ
Tue Jan 12, 2010 4:41 am
Forum: General
Topic: dynamic wireless vlan assignment
Replies: 16
Views: 5976

Re: dynamic wireless vlan assignment

Go for it, we have 5500 cisco for vpn, works perfectly. Now we are up to change nortel to cisco main router with bgp support.
by DannyZ
Tue Jan 12, 2010 12:08 am
Forum: RouterBOARD hardware
Topic: RB750AR anytime soon ?
Replies: 28
Views: 5849

Re: RB750AR anytime soon ?

:D cmon RB532A can run nice and smooth without any problems, only feature i miss is there is no Gbps interface. Sure i agree, MT should realise some cheep soho router with mimo and few Lan ports..
by DannyZ
Tue Jan 12, 2010 12:04 am
Forum: Wireless Networking
Topic: 2.4 ghz links, -60 signal, turbo mode, 13 mbps udp speed
Replies: 21
Views: 2776

Re: 2.4 ghz links, -60 signal, turbo mode, 13 mbps udp speed

@ 93.188.14.7 wlan2 run 2.4Ghz ptp with 93.188.14.11.
by DannyZ
Mon Jan 11, 2010 11:52 pm
Forum: General
Topic: Low disk space
Replies: 7
Views: 2406

Re: Low disk space

First of all, if u are new @ MT. Are You sure u need all instaled packages and Dude un RB433? U can run Dude on regulat PC without any problems. @ terminal go> file print and check stored files. About cleaning web proxy cache >IP..Web Proxy..Web Proxy Settings..Clear Cache. About dude, can't tell u ...
by DannyZ
Mon Jan 11, 2010 11:21 pm
Forum: Wireless Networking
Topic: 2.4 ghz links, -60 signal, turbo mode, 13 mbps udp speed
Replies: 21
Views: 2776

Re: 2.4 ghz links, -60 signal, turbo mode, 13 mbps udp speed

I think the cards are interfering (use more spacing between channels), you should change to 5Ghz for main link and 2.4ghz for clients. You have one card in 2412(20mhz) and one 2437(40Mhz), that means you use overlapping channels. go and check 93.188.14.7 at registration tab 00156D656B3E Signal sect...
by DannyZ
Mon Jan 11, 2010 11:10 pm
Forum: General
Topic: Low disk space
Replies: 7
Views: 2406

Re: Low disk space

How about cleaning all logs (web-proxy, dude ect.)
by DannyZ
Mon Jan 11, 2010 10:12 pm
Forum: Wireless Networking
Topic: 2.4 ghz links, -60 signal, turbo mode, 13 mbps udp speed
Replies: 21
Views: 2776

Re: 2.4 ghz links, -60 signal, turbo mode, 13 mbps udp speed

yup, i think it does. I have same problem with CPE running UB5. After UB5 replacement to R52 everything was fine. My advice would be, try to replace XR2 on 93.188.14.11 and then check what happens with P Troughtput and Tx CCQ.
by DannyZ
Mon Jan 11, 2010 8:14 pm
Forum: RouterBOARD hardware
Topic: RB750AR anytime soon ?
Replies: 28
Views: 5849

Re: RB750AR anytime soon ?

I think normis mean RB411AR with build in 100mW 2.4GHz radio. Course if u need more LAN ports, you should use RB532 or RB532A + RB564 daughter board. Only it's not cheap SOHO router.
by DannyZ
Mon Jan 11, 2010 7:55 pm
Forum: Wireless Networking
Topic: 2.4 ghz links, -60 signal, turbo mode, 13 mbps udp speed
Replies: 21
Views: 2776

Re: 2.4 ghz links, -60 signal, turbo mode, 13 mbps udp speed

I can get Tx over 30mbps from 93.188.14.7 ----> 93.188.14.11 without any problems. But problem appear when running Rx test, it can't hold over 30Mbps more then few seconds. I think it's radio bug or some interefernce between your AP's. And Tx/Rx @ -55/-55 dBm is very nice signal strenght. You shoud ...
by DannyZ
Sun Jan 10, 2010 11:46 pm
Forum: General
Topic: ROS 3.22 web proxy , cannot update dyndns .
Replies: 4
Views: 1219

Re: ROS 3.22 web proxy , cannot update dyndns .

drop here your firewall rules
by DannyZ
Sun Jan 10, 2010 9:55 pm
Forum: General
Topic: ROS 3.22 web proxy , cannot update dyndns .
Replies: 4
Views: 1219

Re: ROS 3.22 web proxy , cannot update dyndns .

And how about Ros upgrade to at least 3.30?
by DannyZ
Sun Jan 10, 2010 9:43 pm
Forum: Wireless Networking
Topic: 2.4 ghz links, -60 signal, turbo mode, 13 mbps udp speed
Replies: 21
Views: 2776

Re: 2.4 ghz links, -60 signal, turbo mode, 13 mbps udp speed

Thats wierd. Can you post your wlan stats screenshot? of both ends -60dBm is Tx/Rx signal strenght?
by DannyZ
Sun Jan 10, 2010 7:35 pm
Forum: Wireless Networking
Topic: 2.4 ghz links, -60 signal, turbo mode, 13 mbps udp speed
Replies: 21
Views: 2776

Re: 2.4 ghz links, -60 signal, turbo mode, 13 mbps udp speed

what routerboard u use? On RB133/133C it's max troughtput.
by DannyZ
Sun Jan 10, 2010 1:45 am
Forum: General
Topic: PPPoE bandwidth limit
Replies: 1
Views: 1704

Re: PPPoE bandwidth limit

should i ask what values u add? ppp profile menu has the tx-bit-rate and rx-bit-rate values, so add values u need for each pppoe client. By default there is bps (bits per second) if u wanna give ppp client 1Mbps on Tx/Rx set it to 1M Tx Rate and 1M Rx rate.
by DannyZ
Sun Jan 10, 2010 1:31 am
Forum: RouterBOARD hardware
Topic: RB750AR anytime soon ?
Replies: 28
Views: 5849

Re: RB750AR anytime soon ?

LOL read your post first. And for future request we have special wiki section. http://wiki.mikrotik.com/wiki/RouterBOA ... re_Request
by DannyZ
Sun Jan 10, 2010 12:33 am
Forum: RouterBOARD hardware
Topic: RB750AR anytime soon ?
Replies: 28
Views: 5849

Re: RB750AR anytime soon ?

u need eol, so take a look on rb/5ex. All features you need plus it has 6xmPCI
by DannyZ
Sat Jan 09, 2010 6:29 pm
Forum: RouterBOARD hardware
Topic: RouterBoard 1000 linux support patch?
Replies: 5
Views: 1166

Re: Boot from CF setting from winbox?

U wanna run ROS with's installed ROS? Maybe im wrong (then point my mistake)
/system routerboard settings>edit>boot-device and change boot device
by DannyZ
Sat Jan 09, 2010 5:58 pm
Forum: RouterBOARD hardware
Topic: RB750AR anytime soon ?
Replies: 28
Views: 5849

Re: RB750AR anytime soon ?

Topic of the year. Use RB450G (CPU@680Mhz, 256MB RAM) And remeber RB750/RB750G is SOHO router not Core router.
by DannyZ
Sat Jan 09, 2010 5:52 pm
Forum: General
Topic: Bandwidth Limit
Replies: 1
Views: 384

Re: Bandwidth Limit

by DannyZ
Sat Jan 09, 2010 1:56 am
Forum: Forwarding Protocols
Topic: Redirect separate IP to other autonomous system (AS)
Replies: 6
Views: 1784

Re: Redirect separate IP to other autonomous system (AS)

Nop, it's not a secret.. :) thanks
by DannyZ
Sat Jan 09, 2010 12:34 am
Forum: Forwarding Protocols
Topic: Redirect separate IP to other autonomous system (AS)
Replies: 6
Views: 1784

Redirect separate IP to other autonomous system (AS)

Is it possable to redirect one external IP (xxx.70.183.44) to an other autonomous system? For example: I have AP, all users have connected to AS83XXX, but i wanna to redirect one client to AS54XXX. I'm WISP who's traffic goes to AS83XXX, and have friend who has ISP with access to AS54XXX. http://fot...
by DannyZ
Fri Jan 08, 2010 12:03 am
Forum: Beginner Basics
Topic: support of 700Mhz mini pci card mikrotik router
Replies: 4
Views: 1073

Re: support of 700Mhz mini pci card mikrotik router

Ubiquiti XR7 (700Mhz Card) runs flawlessly. So i think, you shouldn't have any problems to run 700Mhz cards on MT RB's Mainly it must be Atheros based card.
by DannyZ
Wed Jan 06, 2010 1:32 pm
Forum: General
Topic: Block Teamviewer
Replies: 24
Views: 18191

Re: Block Teamviewer

how about blocking traffic from master.dyngate.com (87.230.73.23) ?
by DannyZ
Tue Jan 05, 2010 1:33 am
Forum: General
Topic: How to achieve this goal?
Replies: 4
Views: 617

Re: How to achieve this goal?

U wanna add queues to all ethernet users, but queue should not limit traffic from several IP's? Or u wanna setup queues for all ethernet users except those who have ect. 219.136.245.128 IP ?
by DannyZ
Tue Jan 05, 2010 12:41 am
Forum: Wireless Networking
Topic: XR3 Freezing?
Replies: 29
Views: 4192

Re: XR3 Freezing?

yup, last night R52H was unstable. Tx speed was >22Mbps, but Rx speed nearly <1Mbps. But it perhaps was antenna fault.
by DannyZ
Tue Jan 05, 2010 12:29 am
Forum: Wireless Networking
Topic: Surge protection?
Replies: 9
Views: 2363

Re: Surge protection?

depends on you cable run. Anyway if cable is installed properly, don't need this gear.
by DannyZ
Mon Jan 04, 2010 12:33 pm
Forum: Beginner Basics
Topic: Reset LAN interface
Replies: 3
Views: 576

Re: Reset LAN interface

Why u are not using user manager? It contains such a feature u need.
by DannyZ
Sun Jan 03, 2010 12:27 am
Forum: RouterBOARD hardware
Topic: Could not change the key - invalid key
Replies: 15
Views: 11986

Re: Could not change the key - invalid key

yup.. maybe someone else can help u.
by DannyZ
Sun Jan 03, 2010 12:01 am
Forum: RouterBOARD hardware
Topic: Could not change the key - invalid key
Replies: 15
Views: 11986

Re: Could not change the key - invalid key

did you try to lose your key?
 /system license> lose-key
Do you really want to lose software key? [y/N]:
by DannyZ
Sat Jan 02, 2010 11:40 pm
Forum: RouterBOARD hardware
Topic: Could not change the key - invalid key
Replies: 15
Views: 11986

Re: Could not change the key - invalid key

Open notepad. Copy your licence key from email ect. -----BEGIN MIKROTIK SOFTWARE KEY------------ lZDo1eSf3egdI/T2hY8fY8OygIZ+UJucjVfOS2+CY+RT McnWOukAdhiQj5HlNLr7+jUlVoEqlqvgACA5X2qbLD== -----END MIKROTIK SOFTWARE KEY-------------- and paste it into notpad. Then Sava As ect. NNFT-86N.key Then take k...
by DannyZ
Sat Jan 02, 2010 11:13 pm
Forum: RouterBOARD hardware
Topic: Could not change the key - invalid key
Replies: 15
Views: 11986

Re: Could not change the key - invalid key

import the attached file with the command '/system license import' (you must upload the licence key to the router's FTP server)
by DannyZ
Sat Jan 02, 2010 12:49 pm
Forum: Wireless Networking
Topic: Oldest release supporting R5H
Replies: 7
Views: 823

Re: Oldest release supporting R5H

Even RB133C's able to run ROS 4.3 av 4.4 without problems. Certainly u should run only those npk u need.
by DannyZ
Fri Jan 01, 2010 8:16 pm
Forum: Beginner Basics
Topic: block router page expect from one ip
Replies: 4
Views: 669

Re: block router page expect from one ip

U're welcome. Yup - starting from ROS 3.30 you can use coma to add more ports to single filter rule and NAT.
by DannyZ
Fri Jan 01, 2010 5:02 pm
Forum: Beginner Basics
Topic: block router page expect from one ip
Replies: 4
Views: 669

Re: block router page expect from one ip

as i remember u can't use multiple ports at single filter rule. You should try add rules by seperate ports. /ip firewall filter add place-before=0 chain=input action=drop src-address=!192.168.2.60/32 protocol=tcp dst-port=21 /ip firewall filter add place-before=0 chain=input action=drop src-address=...
by DannyZ
Fri Jan 01, 2010 4:54 pm
Forum: Wireless Networking
Topic: Bandwidth Management
Replies: 2
Views: 550

Re: Bandwidth Management

by DannyZ
Fri Jan 01, 2010 4:04 pm
Forum: RouterBOARD hardware
Topic: RB Crossroad 1W radio build in?
Replies: 10
Views: 1437

Re: RB Crossroad 1W radio build in?

Yup.. MT card isn't for inceased rates. At the moment my second CPE operates with R52H and it has much better sensitivity compared to Compex WLM54AG-23. Running Compex with 1mW i have 18/18Mbps, but with R52H i have 54/54Mbps with default rates. So no need to increase Tx power. MT rullz by defaults.
by DannyZ
Fri Jan 01, 2010 1:54 pm
Forum: Beginner Basics
Topic: mPCI cards in Routerboard
Replies: 7
Views: 1283

Re: mPCI cards in Routerboard

1th. Why u just can't use edit your post? 2nd. U wanna run RT2561ST A/B/G chipset miniPCI card on RB133? - No i think it woun't run, couz it's not Atheros based. 3rd. I can't understand what u are up to. U wanna use miniPCI-Express card on R133 or x86 based router? If on RB133 - no it's not possable...
by DannyZ
Fri Jan 01, 2010 2:32 am
Forum: Beginner Basics
Topic: upgrade RouterOS v2.9.27
Replies: 9
Views: 2657

Re: upgrade RouterOS v2.9.27

did u try to copy all packages separately?
by DannyZ
Fri Jan 01, 2010 2:21 am
Forum: Beginner Basics
Topic: mPCI cards in Routerboard
Replies: 7
Views: 1283

Re: mPCI cards in Routerboard

i have never heard about RB311 routerboard. And Yes - MT is only for Atheros chipset based radios.
by DannyZ
Fri Jan 01, 2010 1:54 am
Forum: RouterBOARD hardware
Topic: RB Crossroad 1W radio build in?
Replies: 10
Views: 1437

Re: RB Crossroad 1W radio build in?

sure

Default rates:
Image

Increased rates:
Image
by DannyZ
Fri Jan 01, 2010 1:36 am
Forum: RouterBOARD hardware
Topic: RB Crossroad 1W radio build in?
Replies: 10
Views: 1437

Re: RB Crossroad 1W radio build in?

Dont worry, i had Compex WLM54AG-23 (23dBm) card. and i could run it on max (30dBm) without any problems.
by DannyZ
Thu Dec 31, 2009 3:17 pm
Forum: RouterBOARD hardware
Topic: RB600A TVI (interference with TV signal)
Replies: 4
Views: 1049

Re: RB600A TVI (interference with TV signal)

What are the Tx power and frequency on wlan cards? Did U try to use grounding and grounded power supply. Basicly all Mikrotik products ar FCC certified.
by DannyZ
Thu Dec 31, 2009 2:58 pm
Forum: Wireless Networking
Topic: Happy New Year To all Friend Here...
Replies: 1
Views: 430

Re: Happy New Year To all Friend Here...

Thanks.. Same to You

Ring out the old, ring in the new,
Ring, happy bells, across the snow:
The year is going, let him go;
Ring out the false, ring in the true.

Happy New 2010 Year. :D
by DannyZ
Thu Dec 31, 2009 2:53 pm
Forum: General
Topic: add dyndns adress in firewall
Replies: 9
Views: 1228

Re: add dyndns adress in firewall

by DannyZ
Thu Dec 31, 2009 1:28 pm
Forum: Beginner Basics
Topic: torrent speed problem
Replies: 8
Views: 1543

Re: torrent speed problem

What Firewall rules u have @ Filter Rules and NAT? And are u sure about that your ISP/WISP are not queuing p2p trafic by priorety?
by DannyZ
Thu Dec 31, 2009 12:29 pm
Forum: RouterBOARD hardware
Topic: RB Crossroad 1W radio build in?
Replies: 10
Views: 1437

Re: RB Crossroad 1W radio build in?

He he, where is the problem to change Tx power to Card rates and set it to 24dBm? (26dBm (2422-2457MHz), 24dBm (2412, 2462MHz)
by DannyZ
Thu Dec 31, 2009 12:13 pm
Forum: Beginner Basics
Topic: Best way to prevent unauthorized ex-clients accessing i-net.
Replies: 2
Views: 522

Re: Best way to prevent unauthorized ex-clients accessing i-net.

Ok, gonna try it out next month. Thanks
by DannyZ
Wed Dec 30, 2009 9:46 pm
Forum: Wireless Networking
Topic: Exists miniPCI working on ROS at 11Ghz, 18GHz or 28GHz?
Replies: 26
Views: 2867

Re: Exists miniPCI working on ROS at 11Ghz, 18GHz or 28GHz?

if it was possable to make minipci card with 11,18,28Ghz, i think - it where be already done.
by DannyZ
Wed Dec 30, 2009 9:40 pm
Forum: Wireless Networking
Topic: Mikrotik vs NanoStation M5 AirMax MIMO compatibility
Replies: 4
Views: 5572

Re: Mikrotik vs NanoStation M5 AirMax MIMO compatibility

Why not? Use R52n (Support for up to 2x2 MIMO with spatial multiplexing)
by DannyZ
Wed Dec 30, 2009 9:25 pm
Forum: Wireless Networking
Topic: more radio power, could compensate coax length?
Replies: 9
Views: 1581

Re: more radio power, could compensate coax length?

Frequency RG-58 | Belden H-155 | Draka RF-5 | Belden H1000 | Times LMR-400 | Andrew CNT-400 | Times LMR-600 | RFS 2400MHz 66,5 49,6 48,8 23,2 21,9 21,5 14,4 11,6 5600MHz - - - - 34,6 34 23,4 19 These are losses on 100m. And as RK already wrote, Increasing TX Power will not affect on Rx Sensitivity....
by DannyZ
Wed Dec 30, 2009 8:42 pm
Forum: Beginner Basics
Topic: Best way to prevent unauthorized ex-clients accessing i-net.
Replies: 2
Views: 522

Best way to prevent unauthorized ex-clients accessing i-net.

Hi all. Have some question about protection against unauthorized ex-clients. Here is situation: Ex-client who has copied all neighbor list internal IP and MAC addresses (/ip neighbor>print). Hi can change his Wlan MAC to authorized client MAC (those who are on AP Access list) and changing IP, hi is ...
by DannyZ
Wed Dec 30, 2009 6:39 pm
Forum: Wireless Networking
Topic: 500km link posible?
Replies: 15
Views: 2641

Re: 500km link posible?

better check this http://tiktube.com/?video=196, before start your experiment.
by DannyZ
Wed Dec 30, 2009 6:21 pm
Forum: Beginner Basics
Topic: Windows Vista cannot obtain IP from DHCP on RB493
Replies: 8
Views: 3071

Re: Windows Vista cannot obtain IP from DHCP on RB493

create static dhcp lease for W-7/W-V based systems.
by DannyZ
Wed Dec 30, 2009 4:29 pm
Forum: Beginner Basics
Topic: Windows Vista cannot obtain IP from DHCP on RB493
Replies: 8
Views: 3071

Re: Windows Vista cannot obtain IP from DHCP on RB493

have u set pool, add entry to adresss list?
by DannyZ
Wed Dec 30, 2009 2:54 am
Forum: Wireless Networking
Topic: 500km link posible?
Replies: 15
Views: 2641

Re: 500km link posible?

he he, some time ago I read the article on cnet.com about ~380km wireless link. Here is http://www.eslared.org.ve/articulos/Lon ... 0Trial.pdf
by DannyZ
Wed Dec 30, 2009 1:43 am
Forum: Wireless Networking
Topic: Oldest release supporting R5H
Replies: 7
Views: 823

Re: Oldest release supporting R5H

Why u think ROS affect to radio? At least i know it works on 3.30
by DannyZ
Wed Dec 30, 2009 1:02 am
Forum: RouterBOARD hardware
Topic: RB433 cpu mode at regular
Replies: 9
Views: 2655

Re: RB433 cpu mode at regular

Don't know dud, i can do it on RB133C, RB433AH,RB433UAH. Do u have permissions to do that?
by DannyZ
Wed Dec 30, 2009 12:40 am
Forum: General
Topic: 802.11n - optimal configuration
Replies: 2
Views: 1245

Re: 802.11n - optimal configuration

cmon dud, 20Mbps we can run @ 4.7km links by using 22dBi 5Ghz flat panel antennas with overall CCQ >80%. U should try align better it, couz Dual 5G-23D has rather narrow beam width (9°V,9.5°H)
by DannyZ
Wed Dec 30, 2009 12:26 am
Forum: Wireless Networking
Topic: antenna splitter
Replies: 7
Views: 849

Re: antenna splitter

All depends on splitter, basicly it passes DC through it to enable dual amplifiers for each antenna.
by DannyZ
Wed Dec 30, 2009 12:16 am
Forum: RouterBOARD hardware
Topic: RB433 cpu mode at regular
Replies: 9
Views: 2655

Re: RB433 cpu mode at regular

I don know about your problem, but check how i do this :D

View My Video
by DannyZ
Tue Dec 29, 2009 10:38 pm
Forum: RouterBOARD hardware
Topic: RB433 cpu mode at regular
Replies: 9
Views: 2655

Re: RB433 cpu mode at regular

why u think it's cpu bug? it can be ect. condensate in antena, connectors. But anyway /system routerboard settings>edit: cpu-mode and change power-saver to regular then Ctrl+o. and it should be regular as well. No need to reboot.
by DannyZ
Tue Dec 29, 2009 6:48 pm
Forum: Beginner Basics
Topic: Port forwarding is not working
Replies: 7
Views: 1401

Re: Port forwarding is not working

u're up to host web page (server) on dynamic external IP? If it so, u should use dynamic dns client, otherwise you will not be able to host your web page. As far as i know, maybe im wrong about FW rules - add action=accept chain=accept_list comment="Forward HTTP to webserver" dst-address=0.0.0.0/0 d...
by DannyZ
Tue Dec 29, 2009 6:27 pm
Forum: Wireless Networking
Topic: Exists miniPCI working on ROS at 11Ghz, 18GHz or 28GHz?
Replies: 26
Views: 2867

Re: Exists miniPCI working on ROS at 11Ghz, 18GHz or 28GHz?

these issues you should ask to manufacturers. :lol:
by DannyZ
Tue Dec 29, 2009 6:02 pm
Forum: Wireless Networking
Topic: Exists miniPCI working on ROS at 11Ghz, 18GHz or 28GHz?
Replies: 26
Views: 2867

Re: Exists miniPCI working on ROS at 11Ghz, 18GHz or 28GHz?

because miniPCI can't hold it - simple as that.
by DannyZ
Tue Dec 29, 2009 5:59 pm
Forum: Wireless Networking
Topic: Antenna Alignment 50 PTP Link
Replies: 15
Views: 3551

Re: Antenna Alignment 50 PTP Link

over 50km it's normal beam width.
by DannyZ
Tue Dec 29, 2009 5:41 pm
Forum: Wireless Networking
Topic: Exists miniPCI working on ROS at 11Ghz, 18GHz or 28GHz?
Replies: 26
Views: 2867

Re: Exists miniPCI working on ROS at 11Ghz, 18GHz or 28GHz?

these are uvb (11,18,28GHz) devices. SAF Tehnika is Latvian company which developing uvb RF devices, such as Czech Alcoma.
by DannyZ
Tue Dec 29, 2009 3:29 pm
Forum: The User Manager
Topic: mac address authentication
Replies: 3
Views: 4001

Re: mac address authentication

and again, how users are connected to AP? anyway there is no matter what Mac user will set on his cpe. ect user in ARP has 10.1.45.100 IP and 00:0C:42:62:F2:02 MAC and interface Wlan1 + his MAC is registered on Access list - he shouldn't be able to change his internal IP, cauz its not possable to ch...
by DannyZ
Tue Dec 29, 2009 2:40 pm
Forum: Beginner Basics
Topic: RouterOS version info...
Replies: 5
Views: 9573

Re: RouterOS version info...

Sorry - can't get your idea?

Image
by DannyZ
Tue Dec 29, 2009 2:03 pm
Forum: Wireless Networking
Topic: Antenna Alignment 50 PTP Link
Replies: 15
Views: 3551

Re: Antenna Alignment 50 PTP Link

whats the beam width? I suggest to use gps or signal flare.
by DannyZ
Tue Dec 29, 2009 1:16 pm
Forum: Beginner Basics
Topic: Rules Removed Automatically
Replies: 3
Views: 445

Re: Rules Removed Automatically

Check bios battery
by DannyZ
Tue Dec 29, 2009 12:53 pm
Forum: The User Manager
Topic: mac address authentication
Replies: 3
Views: 4001

Re: mac address authentication

sorry- maybe didn't get your idea but u can't change static routes on MT by adding another IP on PC. It will not affect ARP at AP u're connected.
by DannyZ
Tue Dec 29, 2009 12:40 pm
Forum: General
Topic: How to convert Kilobytes to Bytes?
Replies: 8
Views: 1653

Re: How to convert Kilobytes to Bytes?

nop - my bad, it counts 1megabyte equal 1024kilobytes. And as we all know 1byte = 8bits
by DannyZ
Tue Dec 29, 2009 12:31 pm
Forum: Beginner Basics
Topic: RouterOS version info...
Replies: 5
Views: 9573

Re: RouterOS version info...

@ terminal type "system package print" without quotes or go system>packages and u will see instaled packages and ROs verion. Or just take a look at upper left corner - ect. admin@192.168.1.1(AP_Warehouse-5) Winbox - v4.3 on RB433UAH (mipsbe)
by DannyZ
Tue Dec 29, 2009 12:18 pm
Forum: General
Topic: How to convert Kilobytes to Bytes?
Replies: 8
Views: 1653

Re: How to convert Kilobytes to Bytes?

@ MT 10002 = megabyte
by DannyZ
Tue Dec 29, 2009 11:24 am
Forum: Wireless Networking
Topic: Exists miniPCI working on ROS at 11Ghz, 18GHz or 28GHz?
Replies: 26
Views: 2867

Re: Exists miniPCI working on ROS at 11Ghz, 18GHz or 28GHz?

ect. 18GHz saf cfip power consumption ~24W and radio radiotion is ~2V.
by DannyZ
Mon Dec 28, 2009 11:08 pm
Forum: Beginner Basics
Topic: Rules Removed Automatically
Replies: 3
Views: 445

Re: Rules Removed Automatically

What board u use and how old is it? rules disappears after power outage or reboot?
by DannyZ
Mon Dec 28, 2009 10:42 pm
Forum: Wireless Networking
Topic: Exists miniPCI working on ROS at 11Ghz, 18GHz or 28GHz?
Replies: 26
Views: 2867

Re: Exists miniPCI working on ROS at 11Ghz, 18GHz or 28GHz?

do u know miniPCI voltages? :D
3.3V.. why?
and do you know uvb voltages? :lol:
by DannyZ
Mon Dec 28, 2009 4:31 pm
Forum: The Dude
Topic: Dude Maps
Replies: 3
Views: 1420

Re: Dude Maps

Thanks, I knew about static maps. But it would be nice we could use dynamic maps. :)
by DannyZ
Mon Dec 28, 2009 12:06 pm
Forum: Wireless Networking
Topic: Nstream via RB433AH and different radio modes.
Replies: 8
Views: 1406

Re: Nstream via RB433AH and different radio modes.

Okey, i read about nstreame and ros 4.3, i already have downgraded boards on both sides. Will see, will this work better then 5Ghz turbo. by the way 24dbi gri dish is enough for 2.2 miles?
by DannyZ
Sun Dec 27, 2009 7:18 pm
Forum: Wireless Networking
Topic: Nstream via RB433AH and different radio modes.
Replies: 8
Views: 1406

Re: Nstream via RB433AH and different radio modes.

there is another clients connected to these AP's.
by DannyZ
Sat Dec 26, 2009 9:50 pm
Forum: Wireless Networking
Topic: Nstream via RB433AH and different radio modes.
Replies: 8
Views: 1406

Re: Nstream via RB433AH and different radio modes.

Thanks, i've already read this article. Tommorow will try set it up, after it will post replay with results.

By the way - will nstream work to CPE (RB433 with 2xR52 and one 2.4 flat directional and 5Ghz grid dish) Hi is connected on 2.4Ghz with Tx-69/Rx-72dBm. AP has two omni (5300Mhz and 2427Mhz)
by DannyZ
Sat Dec 26, 2009 6:40 pm
Forum: Wireless Networking
Topic: Nstream via RB433AH and different radio modes.
Replies: 8
Views: 1406

Re: Nstream via RB433AH and different radio modes.

Sorry, didn't get your idea about single link Nstream. I mean tower A recives data from tower B with 5Ghz parabolic dish and send data to tower B with 2.4Ghz grid dish.
Tower A XR5@5310Mhz <------RX------| XR5@5310Mhz Tower B
        SR2@2432Mhz |------TX------> SR2@2432Mhz
by DannyZ
Sat Dec 26, 2009 12:47 am
Forum: Wireless Networking
Topic: Clients Disconnections Problems
Replies: 4
Views: 654

Re: Clients Disconnections Problems

Ou my bad, 4.4 already is stable. Sorry bout that.
by DannyZ
Fri Dec 25, 2009 10:31 pm
Forum: RouterBOARD hardware
Topic: RouterOS Bandwidth Test Implementation
Replies: 1
Views: 787

Re: RouterOS Bandwidth Test Implementation

1th of all TCP use defaut buffer length, segment size. Run BT test from Router A and just setup BT Server on needed wireless link Router B. Router A run BT Test to *ect 10.11.51.100 <------------------> Router B with enabled BT Server *ect 10.11.51.1 Dont forget to use Router B username and password...
by DannyZ
Fri Dec 25, 2009 10:17 pm
Forum: Wireless Networking
Topic: Clients Disconnections Problems
Replies: 4
Views: 654

Re: Clients Disconnections Problems

did u snoop area? And why u run unstable ROs on important network? U should try to snopp area, and recall ROs by downgrading it to 4.3 (stable)
by DannyZ
Fri Dec 25, 2009 9:57 pm
Forum: Wireless Networking
Topic: Nstream via RB433AH and different radio modes.
Replies: 8
Views: 1406

Nstream via RB433AH and different radio modes.

Hi.

Is it possable to setup nstream with two RB433AH?
Is it possable to setup nstream with Rx 5Ghz 802.11a @ 5310Mhz and Tx 2.4Ghz 802.11g @ 2432Mhz
by DannyZ
Fri Dec 25, 2009 1:45 pm
Forum: The Dude
Topic: Dude Maps
Replies: 3
Views: 1420

Dude Maps

Im new in Dude and maybe there is already such a feature as dynamic google map. If there is, can someone give me guide, how o set it up. If there is no such a feature, maybe MT can make it? (I wanna option that allows to add dynamic google map). ect i have local topological map, and i have some cost...
by DannyZ
Fri Dec 25, 2009 9:31 am
Forum: Scripting
Topic: ACK timeout script
Replies: 2
Views: 1358

Re: ACK timeout script

Sorry, just bought RB433AH/UAH for all AP.
by DannyZ
Thu Dec 24, 2009 5:32 pm
Forum: General
Topic: Merry Xmas all MT users
Replies: 8
Views: 868

Merry Xmas all MT users

Merry Xmas all Mikrotik Users all over the world.

Image
by DannyZ
Thu Dec 24, 2009 1:42 pm
Forum: Beginner Basics
Topic: setting up DNS
Replies: 5
Views: 1163

Re: setting up DNS

If u wanna setup dns i think its not right place to do that. look at IP>DHCP server>networks>dns server.
by DannyZ
Wed Dec 23, 2009 6:34 pm
Forum: Scripting
Topic: ACK timeout script
Replies: 2
Views: 1358

ACK timeout script

Hello all. have question about ACK timeout script. Will this : foreach i in=[/interface wireless find ] do={/interface wireless monitor $i once do {:if ($current-ack-timeout > 100) do {:local tmpfreq [interface wireless get [/interface wireless find interface=$i] frequency] ; :log info $tmpfreq ; :s...
by DannyZ
Wed Dec 23, 2009 2:53 pm
Forum: Beginner Basics
Topic: torrent speed problem
Replies: 8
Views: 1543

Re: torrent speed problem

if it's not solution, try to make Nat rulle with masquarade action.
by DannyZ
Wed Dec 23, 2009 1:48 pm
Forum: Beginner Basics
Topic: torrent speed problem
Replies: 8
Views: 1543

Re: torrent speed problem

and server u use? we should discover ir on our crystal balls? :))
by DannyZ
Wed Dec 23, 2009 1:44 pm
Forum: Wireless Networking
Topic: XR2 problems, check your AP's
Replies: 1
Views: 515

Re: XR2 problems, check your AP's

we have same proble. Problem still not solved, all i know, it's not radio bug. We did change RB532A + 3x wistron cm-11 to RB433AH + XR5 + SR2 + SR5, result the same. When total traffic on 2.4 reach >4.7Mbps, all clients get average latency over 100ms. Even on local (AP to client ping). But no proble...
by DannyZ
Wed Dec 23, 2009 1:26 pm
Forum: General
Topic: [ASK] How to block Ultrasurf ???
Replies: 5
Views: 7985

Re: [ASK] How to block Ultrasurf ???

How about blocking 9666 port?
by DannyZ
Tue Dec 22, 2009 10:57 pm
Forum: Beginner Basics
Topic: Wisp Configuration
Replies: 4
Views: 906

Re: Wisp Configuration

all depends, how many client u are up to. We have several AP connected in WDS and we had some problems with high latency. Otherway, everything works fine for us. 11 access points and 179clients.
by DannyZ
Tue Dec 22, 2009 11:25 am
Forum: Beginner Basics
Topic: 2.4Ghz Snooper
Replies: 5
Views: 1081

Re: 2.4Ghz Snooper

:D :D my bad, sorry. I get disconnected not reboot. And i get disconnect cauz i'm connected to AP using 2.4Ghz. And when i try to snoop it disconnects all clients connected to it.
by DannyZ
Mon Dec 21, 2009 3:11 pm
Forum: Beginner Basics
Topic: 2.4Ghz Snooper
Replies: 5
Views: 1081

Re: 2.4Ghz Snooper

Ok. Two R52 (2.4 & 5Ghz AP) R5H WDS
by DannyZ
Sat Dec 19, 2009 2:09 pm
Forum: Beginner Basics
Topic: v4.3 and RB433's
Replies: 4
Views: 1244

Re: v4.3 and RB433's

U can't access RB through winbox, IP telnet? I would recommend u to use Netinstall. But if u are able to access your RB through console, telnet or winbox, just use command [admin@Mikrotik] >system package downgrade
by DannyZ
Sat Dec 19, 2009 1:48 pm
Forum: Beginner Basics
Topic: 2.4Ghz Snooper
Replies: 5
Views: 1081

Re: 2.4Ghz Snooper

system package print Flags: X - disabled # NAME VERSION SCHEDULED 0 system 4.3 1 dhcp 4.3 2 mpls 4.3 3 ppp 4.3 4 routing 4.3 5 routeros-mipsbe 4.3 6 routerboard 4.3 7 security 4.3 8 hotspot 4.3 9 wireless 4.3 10 X ipv6 4.3 11 advanced-tools 4.3 Board RB433AH fresh - running few weeks Thanks
by DannyZ
Thu Dec 17, 2009 7:52 pm
Forum: Beginner Basics
Topic: Wisp Configuration
Replies: 4
Views: 906

Re: Wisp Configuration

disable default forwarding.
by DannyZ
Thu Dec 17, 2009 2:00 pm
Forum: Beginner Basics
Topic: 2.4Ghz Snooper
Replies: 5
Views: 1081

2.4Ghz Snooper

Hi, have problems with 2.4Ghz snooper. When i try to snoop network on 2.4Ghz, AP reboots. :(
by DannyZ
Mon Dec 14, 2009 2:46 pm
Forum: Beginner Basics
Topic: disable unauthorized users
Replies: 2
Views: 442

Re: disable unauthorized users

I have 3 AP connected togather with 5GHz WDS and each AP has 2.4Ghz and 5Ghz broadcasting omni. I just set MAC authentication. Time will show results, but at the moment all clients has normal latency and high speed connection. But this related by replacing radios from wistrons to xr series by ubiqui...
by DannyZ
Mon Dec 14, 2009 12:37 pm
Forum: Beginner Basics
Topic: Bug Issue
Replies: 4
Views: 506

Re: Bug Issue

I just replace Wistrons with XR5 and XR2, now looks evething works perfect, all clients has low latency and high performance.
by DannyZ
Mon Dec 14, 2009 11:08 am
Forum: Beginner Basics
Topic: Bug Issue
Replies: 4
Views: 506

Re: Bug Issue

Okey. It can cause high latency for other clients and router hungs?
by DannyZ
Sun Dec 13, 2009 7:10 pm
Forum: Beginner Basics
Topic: disable unauthorized users
Replies: 2
Views: 442

disable unauthorized users

Hi, how to disable unauthorized user access. I dont know, is this cause my problems. Always when user attempt all users get average hight latency and poor bandwidth speed. How to disable one user attempts?
by DannyZ
Sun Dec 13, 2009 12:45 am
Forum: Beginner Basics
Topic: Bug Issue
Replies: 4
Views: 506

Bug Issue

Hi. Have some strange problem on RB433UAH. Every day i get this in log dec/12 21:05:41 wireless,info 00:08:21:31:50:B7@wlan3: disconnected, extensive d ata loss dec/12 21:05:51 wireless,info 00:08:21:31:50:B7@wlan3: connected dec/12 21:06:07 wireless,info 00:08:21:31:50:B7@wlan3: reassociating dec/1...
by DannyZ
Sat Dec 12, 2009 9:19 pm
Forum: Beginner Basics
Topic: Sawmill firewall/log analysis
Replies: 1
Views: 1279

Sawmill firewall/log analysis

Hi, does ROS 4.3 support Sawmill? If it so, how to locete log patch destination? Thanks
by DannyZ
Wed Dec 09, 2009 3:48 pm
Forum: Beginner Basics
Topic: Monitoring Network thru SMS Alerts
Replies: 3
Views: 706

Re: Monitoring Network thru SMS Alerts

Ok, i'll try this out.
by DannyZ
Tue Dec 08, 2009 8:32 pm
Forum: Scripting
Topic: Auto supout script.
Replies: 4
Views: 786

Re: Auto supout script.

Okey, thanks a lot. :)
by DannyZ
Tue Dec 08, 2009 8:20 pm
Forum: Beginner Basics
Topic: Monitoring Network thru SMS Alerts
Replies: 3
Views: 706

Monitoring Network thru SMS Alerts

Hi.

Can i use Huawei E1550 USB broadband dongle stick modem to run SMS alerts on RB433UAH (ROS 3.30).

Best Regards.
by DannyZ
Tue Dec 08, 2009 3:16 am
Forum: Scripting
Topic: Auto supout script.
Replies: 4
Views: 786

Re: Auto supout script.

supout.rif is same a router configuration?
by DannyZ
Mon Dec 07, 2009 2:50 pm
Forum: Scripting
Topic: Auto supout script.
Replies: 4
Views: 786

Auto supout script.

Hi, can someone drop script to make supout.rif every day 6am?
by DannyZ
Wed Nov 25, 2009 8:10 pm
Forum: Scripting
Topic: Auto reboot script
Replies: 7
Views: 25331

Re: Auto reboot script

Thanks a lot. :)
by DannyZ
Wed Nov 25, 2009 6:41 pm
Forum: Scripting
Topic: Auto reboot script
Replies: 7
Views: 25331

Auto reboot script

Hi.

Can someone post auto reboot script? I need to reboot AP every day at 6am. Is it possable?
by DannyZ
Fri Nov 20, 2009 9:34 pm
Forum: Beginner Basics
Topic: Trace weakest point in chain.
Replies: 0
Views: 324

Trace weakest point in chain.

Hi again.

How to trace the weakerst system or link point which is reason of high latency to all connected clients. Should i trace connection from my Router to external IP? Or better use Dude?
by DannyZ
Fri Nov 20, 2009 9:28 pm
Forum: Beginner Basics
Topic: DNS Changing Error !
Replies: 2
Views: 684

Re: DNS Changing Error !

You can change it in your computer IP settings.
by DannyZ
Fri Nov 20, 2009 4:30 pm
Forum: Beginner Basics
Topic: RB411 Max Throughput
Replies: 7
Views: 1052

Re: RB411 Max Throughput

ok, thanks all.
by DannyZ
Fri Nov 20, 2009 3:37 pm
Forum: Beginner Basics
Topic: RB411 Max Throughput
Replies: 7
Views: 1052

Re: RB411 Max Throughput

At the moment TX/RX Signal Strenght is 56/62dBm, TX/RX CCQ 100/100%, Overall CCQ 100%. AP max troughtput is 54Mbps, and i don't have any limits by ISP.
by DannyZ
Fri Nov 20, 2009 5:40 am
Forum: Beginner Basics
Topic: RB411 Max Throughput
Replies: 7
Views: 1052

Re: RB411 Max Throughput

It will be used as CPE
by DannyZ
Fri Nov 20, 2009 12:28 am
Forum: Beginner Basics
Topic: RB411 Max Throughput
Replies: 7
Views: 1052

RB411 Max Throughput

Does max download and upload speed depends from routerboard? at the moment i have old dinosaur RB133 and max speed i get is 7mbps both ways. Will new RB gain my speed? Whats the max speed for RB411 and RB411AH. Thanks
by DannyZ
Thu Nov 19, 2009 6:30 pm
Forum: Wireless Networking
Topic: Access Point based on MikroTik
Replies: 2
Views: 563

Re: Access Point based on MikroTik

better get pci to pci mini adapter and get R52n radio. And what u mean by word Access point? indoor or outdoor AP?
by DannyZ
Thu Nov 19, 2009 5:53 pm
Forum: Beginner Basics
Topic: dst-nat dont work, what is wrong ?
Replies: 8
Views: 1312

Re: dst-nat dont work, what is wrong ?

Why u wanna forward all ports? As action use masquarde if u are connected to AP with single IP for all clients.
by DannyZ
Wed Nov 18, 2009 8:45 pm
Forum: Beginner Basics
Topic: Basic router setup guide/tutorial ?
Replies: 97
Views: 37447

Re: Basic router setup guide/tutorial ?

Scan for AP, then connect. Setup dhcp server, pool, route and NAT
by DannyZ
Thu Oct 15, 2009 6:41 pm
Forum: Beginner Basics
Topic: Real IP for client.
Replies: 2
Views: 763

Re: Real IP for client.

Nop, im just home user + im sharing my network with neighbors. AP im connected are owned by state and it free of charge, only AP admin was not sure, will it help discrase my Latency. Now i have approx. 100ms to abroad countries and 15-20ms to local (Latvia servers). AP has 1 external IP, and all use...
by DannyZ
Wed Oct 14, 2009 8:44 pm
Forum: Wireless Networking
Topic: Tx/Rx rate
Replies: 2
Views: 864

Re: Tx/Rx rate

ok, thanks
by DannyZ
Tue Oct 13, 2009 5:30 pm
Forum: Beginner Basics
Topic: Real IP for client.
Replies: 2
Views: 763

Real IP for client.

Hi.

Will it improve my latency if i will have my own external IP? Now there is above 30 clients on same external IP. As i know, likelihood there is IPIP option so set CPE with own external IP over transparent link. scheme i'm connected to world :))Image
by DannyZ
Mon Oct 12, 2009 6:03 pm
Forum: Wireless Networking
Topic: Tx/Rx rate
Replies: 2
Views: 864

Tx/Rx rate

Hi All..

Just curiosity. Should my Tx/Rx rates be approximately equal if im using only one antenna (Itelite SRA-50016)
I have Image
by DannyZ
Mon Oct 12, 2009 1:27 am
Forum: Beginner Basics
Topic: Antenna modes
Replies: 5
Views: 986

Re: Antenna modes

There was R52, now has R52H with ar5414 chipset
by DannyZ
Sun Oct 11, 2009 8:22 pm
Forum: General
Topic: V3.3 stalls eth0 on RB133's
Replies: 4
Views: 676

Re: V3.3 stalls eth0 on RB133's

Hi I has same problem. But i found solution for this situation. But i don't know, will it be solution for your problem. I use my RB133C as CPE. I just update it from ROS 2.9.51 to 3.30, after 3.30 up to 4.0rc1 with following npk. (dhcp,routering,system and wireless) Reason your RB133's hungs (power ...
by DannyZ
Sat Oct 10, 2009 7:33 pm
Forum: Beginner Basics
Topic: Antenna modes
Replies: 5
Views: 986

Re: Antenna modes

Ok, thanks a lot..
by DannyZ
Fri Oct 09, 2009 9:44 pm
Forum: Beginner Basics
Topic: Antenna modes
Replies: 5
Views: 986

Antenna modes

Hi friends. Which Antenna mode i must use, if i have only one antenna connected to main connector on R52H. Should it be antenna a mode? Now i have rx-a/tx-b . B is AUX connector on PCI-Mini? if it so, will it increase speed, if i'll plug another (23dBi Grid) to A connector and reconnect Flat antenna...
by DannyZ
Tue Oct 06, 2009 7:25 am
Forum: Beginner Basics
Topic: ROS hangs opening Terminal
Replies: 8
Views: 1150

Re: ROS hangs opening Terminal

Ok, i already get needed info from MT support team, but anyway thanks all. I will buy rb411ah. hope it will be much better.
by DannyZ
Sat Oct 03, 2009 6:00 pm
Forum: Beginner Basics
Topic: ROS hangs opening Terminal
Replies: 8
Views: 1150

Re: ROS hangs opening Terminal

Main reason my RB hungs and reboots is not enough memory (when free RAM memory reaches 2300KB = reboot)
by DannyZ
Wed Sep 30, 2009 5:11 pm
Forum: Beginner Basics
Topic: RouterBOARD 133C3
Replies: 5
Views: 3756

Re: RouterBOARD 133C3

dafault IP is 192.168.88.1

Just open winbox and click search button, and connect it by IP or MAC address.
by DannyZ
Wed Sep 30, 2009 4:39 pm
Forum: Beginner Basics
Topic: ROS hangs opening Terminal
Replies: 8
Views: 1150

Re: ROS hangs opening Terminal

http://fotohost.lv/images/vlnj42fvyqsdckahu8w2.jpg Just downgrade to 2.9.51. So which npk i must instal for CPE Just update it to 3.30 with these npk and looks fine, Maybe there is some npk i don't need for CPE? http://fotohost.lv/images/yjgd3iq1wqs80xcgdhyv.jpg when free memory count to 2300KB rou...
by DannyZ
Wed Sep 30, 2009 3:27 pm
Forum: Beginner Basics
Topic: ROS hangs opening Terminal
Replies: 8
Views: 1150

Re: ROS hangs opening Terminal

Ok, reason this happens? it maybe my RB can't work with 3.30? or i must instal those system option i will use, not all, as i did. RB133c3
by DannyZ
Wed Sep 30, 2009 3:08 pm
Forum: Beginner Basics
Topic: ROS hangs opening Terminal
Replies: 8
Views: 1150

ROS hangs opening Terminal

Hi. New day, new problem. My ROS hangs everytime i start new terminal (Router disconnected message pops up). I just want downgrade my ROS from 3.30 to 2.9.51. I have transported all needed npk to router with Filezilla. And now i need to set "system package downgrade" but i can't open terminal. Same ...
by DannyZ
Tue Sep 29, 2009 8:48 pm
Forum: RouterBOARD hardware
Topic: DHCP error
Replies: 1
Views: 461

DHCP error

Hello. I tried to upgrade my ROS from 2.9.51 to 3.30, but after upgrade my DHCP server goes crazy. It disconnect my PC ( over ethernet) and refuses to give me IP. And PC takes automatic private IP, not 192.168.0.20 as always, but somthing like 164.172.152.254. Pool are the same (192.168.0.10-192.168...
by DannyZ
Tue Sep 22, 2009 2:54 pm
Forum: General
Topic: High and unstable latency
Replies: 3
Views: 610

Re: High and unstable latency

Problem solved. Atheros [censored]
by DannyZ
Mon Sep 21, 2009 2:45 am
Forum: General
Topic: High and unstable latency
Replies: 3
Views: 610

Re: High and unstable latency

Nop, There is no limits. Even ISP hasn't set limit to me.
by DannyZ
Sat Sep 19, 2009 10:49 pm
Forum: General
Topic: High and unstable latency
Replies: 3
Views: 610

High and unstable latency

Hello Have a problem. My latency is unstable, it jump up and down. When i test my speed at speedtest.net, average latency on country servers are 20ms, outside country 40-55ms. But when i play online game (BF2142) latency goes from 50-200ms, It can be, because for gameplay needet TCP/UDP ports ar clo...
by DannyZ
Wed Sep 09, 2009 4:41 pm
Forum: Forwarding Protocols
Topic: Failure with port forwarding
Replies: 1
Views: 902

Failure with port forwarding

Hi all.. I have some problems with port forwarding. i have forwarded needed ports in firewall - NAT Chain: dstnat Dst.address: 212.70.xxx.2(my external IP) Protocol: 6 (tcp) or 17 (udp) Dst. port: xxxx (forwarded port) Action: dst-nat To-address: 10.11.44.xx (my internal IP) To-ports: xxxx (forwarde...
by DannyZ
Wed Sep 09, 2009 4:05 pm
Forum: General
Topic: mikrotik t-shirts
Replies: 40
Views: 11875

Re: mikrotik t-shirts

Ubnt gives t-shirts for free.. ;) But anyway, great idea, any advanced mt user should have one of those stufs. :)
by DannyZ
Tue Sep 08, 2009 10:00 pm
Forum: General
Topic: Tx down..
Replies: 0
Views: 294

Tx down..

Hi Folks.

Have a problem. My Tx Level is Zerro (0). Can anyone help me out?
Here is screen..

Thanks