@Normis How "random12" user could show us results of "ps", "ls" etc ... Is he cracking his own router or uses some Mikrotik's debug/special module? Simple question: How? There exists a special NPK package that you can install and gain access to shell. This is not publi...

Hello! I will share here the reply from the support.... You need to swap src-address and dst-address parameters in places for your policy template. Src-address should be the split network and dst-address should be remote peers dynamic address pool. This tip solved my issue/bad configuration upgradin...

Hello I've upgraded from bugfix version 6.37.5 to the last bugfix 6.38.7 and the IPsec tunnel does not work anymore . I've tested this issue with 5/6 setup in different infrastructure, with multiple IPsec client (Apple, Windows, etc...) I've opened a new thread for this issue: https://forum.mikrotik...

Hello I've upgraded my devices from bugfix version 6.37.5 to the last bugfix 6.38.7 and the IPsec tunnel does not work anymore . I've tested this issue with 5/6 setup in different infrastructure, with multiple IPsec client (Apple, Windows, etc...) This is the log: 13:57:41 ipsec,info XAuth login suc...

Hello! How we can know the changes from the previous "bugfix" version? Is it the changelog for "bugfix version" full or we need to check version by version? (example 6.37.3, 6.37.2, 6.37.1, 6.37.0.....) In case of we need to read all changelogs, where we can found it in a unique ...

I think you will only have a problem when you have deployed your routers with nonstandard config, forcing the MTU of the PPPoE connection to 1500 or so. Is that the case? And what do you want to happen now? Is it only an advise for the community? Hello! All my routers/clients are all with standard ...

Dear users,
the problem is still present !!!

If you upgrade your Access Concentrator (PPPoE Server) for 6.32.4 (Bugfix only) to 6.35 (Current) about 30% of destination for all your PPPoE Client with "<=6.32.4" will be unreachable!!!

Dear Mikrotik customers, we have upgraded our PPPoE Core access concentrators from 6.31/6.32.3 to 6.33.x (example 6.33.5) In this 6.33.x version Mikrotik moved from non-standard large PPPoE MTU support to *) RFC4638 (MTU larger than 1488). Upgrading only the core, but not the client, TCP/MTU will be...

It sounds more like a hardware issue. If not that, then probably an RMA (warranty) is the only easy way unless you know how to check the trace connections and about soldering on the PCB. Hello, unfortunately we noticed the following situation: We got a new product (Mikrotik RouterBoard 2011UAS-RM),...

Hello! The Huawei E1820 (14.4Mbit) is not recognized under Mikrotik 6.x It's detected only under System -> Resources -> USB with "HUAWEI MOBILE", but not under ppp/interface. Here the output with Mikrotik 5.25 where it's work correctly: [admin@MikroTik] /interface ppp-client> info 0 status...

Is not possible?
Thanks again

It sounds more like a hardware issue. If not that, then probably an RMA (warranty) is the only easy way unless you know how to check the trace connections and about soldering on the PCB. Hello sergejs, thanks for your reply. We have opened RMA/warranty for that product! No problem with other 6.4 pr...

Hello! For my Mikrotik L2TP+IPsec server I've opened that ports: - PROTO 50 ESP, - Port 500 UDP (ISAKMP), - Port 4500 UDP (NAT-T) and... I need to accept packets to the L2TP service (1701), but not just any packet: only those that are part of a IPSec SA . This is the right rule over linux: iptables ...

Hello Oldman,
thanks for your reply.

My Cisco is WS-C2960S-24TS-S with firmware 12.2(58)SE2 (C2960S-UNIVERSALK9-M).
It's the last stable version for 12.2 series....
And why i've the problem only with that MKT-eth3 port?
All other MKT-Giga ports are connectet to that Cisco

Thanks!

Hello! After 6h without problem (over eth6) i've moved newly the cable to ether3... same problem! Could you tell me if it's an HW or SW problem? Thanks 2 R name="ether3" driver-rx-byte=358 383 988 driver-rx-packet=632 837 driver-tx-byte=1 025 577 212 driver-tx-packet=881 271 rx-bytes=360 8...

Hello to All! I've a new RB2011UAS ....with firmware v.6.4 and routerboard firmware 3.08 I've connected all 5 Giga Ports to one Cisco Giga Swtich with 2mt cable cat6. The Ether3 RX bad CRC (Rx FCS Error) and go down/up. No problem on over other MKT Giga ETH (1, 2, 4 and 5) I've moved the cable to Et...

Hello! I need to convert this " Linux " config to " Mikrotik config ". I've TWO internet lines: HDSL and ADSL. HDSL is the default gateway (ETH2) I need to connect to Mikrotik (VPN) from "ADSL PORT". In this way all connection from/to ADSL will be forwarded over them an...

I can confirm an issue with SSTP server described above "self signed certificate in certificate chain" after upgrading from 5.12 to 5.13 . Try to remove CA certificate used for SSTP server and then import it back, for me it started working again (SSTP server side). Hi Reimporting CA certi...

Hi! v5.13 resolve one issue that I have indicated (webfig) but introduce two big problem with SSTP network ! After upgrade "SSTP SERVER" (build with Mikrotik) can't autenticate other SSTP CLIENT (Mikrotik) The SSTP Server drop connection with: " sstp-0 terminating... - self signed cer...

Hello to all! I'm need simple "linux router" as Virtual router with MetaROUTER. DD-WRT is too heavy for my MTIK CPU and instable. Where I can found "minimal linux" for use it with MetaROUTER? Thanks! PS: may be good another "isolated" mikrotik as MetaROUTER. Is it possi...

http://wiki.mikrotik.com/wiki/All_about ... ense_Level

Thanks!

Hello!

I have RB411 with License L3.

I need to upgrade to L4 or L5.

Is there a procedure/discount for upgrade it?

Thanks

of course, when it's not transmitting, there is no need to run at the high rates.

Hi normis, thanks for reply!

I have this "jump" only in "one direction" and I'm using this radio link in WDS mode.
It's correct?

Thanks again!

Sim

Hello! I have two RB411 in WDS mode. In " no traffic mode " this is the status. TX/RX Rate: 54Mbps/54Mbps ~ 54Mbps/6Mbps (Continuously!) Tx/RX Signal: -56/-55 dBm Noise: -96 dBm Signal To Noise: 42 dB TX/RX CCQ: 91/96 % Overall: 89 % In " traffic mode " this is the status TX/RX R...