Community discussions

Search found 16 matches

by Prewest
Tue Sep 10, 2019 9:22 am
Forum: Beginner Basics
Topic: 1 interface, 2 vlans, prioritize Vlan2 95%
Replies: 8
Views: 966

Re: 1 interface, 2 vlans, prioritize Vlan2 95%

how about vlan priority? https://wiki.mikrotik.com/wiki/Manual:WMM#How_to_set_priority + shaping vlan2 to 95% of bandwidth Could not get this to work, but fixed it in another way.. On VLAN 1 = 80% limit, VLAN2 can have 100% of the entire connection. Seems to work OK, normally VLAN2 just uses 10/15%...
by Prewest
Thu Sep 05, 2019 10:23 am
Forum: Beginner Basics
Topic: 1 interface, 2 vlans, prioritize Vlan2 95%
Replies: 8
Views: 966

Re: 1 interface, 2 vlans, prioritize Vlan2 95%

Well, VLANs are Layer 2 - I don't believe you can "guarantee" layer 3 capacity. If you have a 100mbps interface, give vlan1 95mbps, and vlan2 5mbps via simple queues. More than that, I don't think you can do. Ok, I also have control over the Layer 3 subnets (both VLAN`s have IP addresses assigned o...
by Prewest
Thu Sep 05, 2019 9:41 am
Forum: Beginner Basics
Topic: 1 interface, 2 vlans, prioritize Vlan2 95%
Replies: 8
Views: 966

Re: 1 interface, 2 vlans, prioritize Vlan2 95%

Anav: Good question, I believe want you want to look into is queues! Martinclaro: To do that, you will need to do load-balancing + failover (search for PCC or ECMP). This I know, I already have several working simple queues and queue tree's in my infrastructure that work perfectly; But how to make a...
by Prewest
Wed Sep 04, 2019 6:22 pm
Forum: Beginner Basics
Topic: 1 interface, 2 vlans, prioritize Vlan2 95%
Replies: 8
Views: 966

1 interface, 2 vlans, prioritize Vlan2 95%

Hi, I`m a little bit stuck, here`s my scenario; I have 1 interface, 100mbit up and down. Over this interface I have 2 vlans running, 55 and 57. Now from the total link I need to prioritize vlan 57 for about 95% of total bandwidth up and down (only when used). What is the best approach here? Maybe if...
by Prewest
Sun Jun 23, 2019 11:19 am
Forum: Forwarding Protocols
Topic: Multicast [SOLVED]
Replies: 9
Views: 1082

Re: Multicast [SOLVED]

I`m missing the forward rule in the firewall, I don`t know the command out of my head but it should be

Firewall -> add rule -> forward -> DST-Adress = 224.0.0.0/4 -> -> in interface / out interface -> action accept or passthrough..
by Prewest
Thu Jun 20, 2019 9:57 am
Forum: Forwarding Protocols
Topic: 2x Mikrotik CCR1072 UDP out-of-order issue
Replies: 3
Views: 644

Re: 2x Mikrotik CCR1072 UDP out-of-order issue

If someone runs into the same issue, I have found the problem;

On one SFP+ interface flow control was set on auto, after setting flow control on OFF the problem was gone..
by Prewest
Wed May 29, 2019 3:25 pm
Forum: Forwarding Protocols
Topic: 2x Mikrotik CCR1072 UDP out-of-order issue
Replies: 3
Views: 644

Re: 2x Mikrotik CCR1072 UDP out-of-order issue

I just checked, there is no loadbalancer active on that link
by Prewest
Wed May 29, 2019 1:47 pm
Forum: Forwarding Protocols
Topic: 2x Mikrotik CCR1072 UDP out-of-order issue
Replies: 3
Views: 644

2x Mikrotik CCR1072 UDP out-of-order issue

Hi all, 1st: CCR1072 firmware 6.44.2 2nd: CCR1072 firmware 6.44.3 I have 2 CCR1072 routers in 2 different datacenters, both routers are connected with eachother via a 10GB dedicated link.. Now there are UDP streams going over this link but the packets are one-way out-of-order. When using iperf (on 2...
by Prewest
Wed Apr 26, 2017 6:07 pm
Forum: General
Topic: Connection drop every 60 sec (or random at load) on link (with VLAN)
Replies: 2
Views: 398

Re: Connection drop every 60 sec (or random at load) on link (with VLAN)

Removed the bridge..
Problem solved..

Thanks!
by Prewest
Wed Apr 26, 2017 4:15 pm
Forum: General
Topic: Connection drop every 60 sec (or random at load) on link (with VLAN)
Replies: 2
Views: 398

Connection drop every 60 sec (or random at load) on link (with VLAN)

Hi everbody, I have a problem with 2 mikrotiks, the 2011UiAS and the 3011UiAS. We have 2 datacenters that is connected with an NDIX, previously we used a sophos UTM to bridge the datacenters but we wanted to lower the load on the Sophos UTM. So we have placed mikrotiks instead with the routing table...
by Prewest
Wed May 16, 2012 10:30 pm
Forum: The Dude
Topic: Value's of multiple data sources into 1 Chart
Replies: 7
Views: 1773

Re: Value's of multiple data sources into 1 Chart

it`s working..
thanks for you`re advice..

what i did was add a static value of 0.001, i won`t show up on the chart but it will show the probe as "UP".
by Prewest
Tue May 15, 2012 10:27 pm
Forum: The Dude
Topic: Value's of multiple data sources into 1 Chart
Replies: 7
Views: 1773

Re: Value's of multiple data sources into 1 Chart

Sorry, the ip address needs to be in quotes. oid("1.3.6.1.4.1.1768.100.70.10.2.1.2.1", 10, 5, "81.28.86.107") It works, thanks! one more thing, when the value of the "SIP_TOTAL" is 0, i`m getting that the probe is down.. i`m using: available: SIP_TOTAL() > 0 Error: if(SIP_TOTAL() > 0, "", "SIP GESP...
by Prewest
Tue May 15, 2012 1:05 pm
Forum: The Dude
Topic: Value's of multiple data sources into 1 Chart
Replies: 7
Views: 1773

Re: Value's of multiple data sources into 1 Chart

hmm it doesn`t seem to work..

i made a function called: SIPCALL1
the error i`m getting = oid("1.3.6.1.4.1.1768.100.70.10.2.1.2.1", 10, 5, 81.28.86.107)

with the function SIP_TOTAL i`m getting a parse failed error.
by Prewest
Sun May 13, 2012 9:23 pm
Forum: The Dude
Topic: Value's of multiple data sources into 1 Chart
Replies: 7
Views: 1773

Value's of multiple data sources into 1 Chart

Hi,,

i`ve made several data-sources from different devices, now i want to add up the numbers (example : 1+2+6 = 9) of these datasources and show them in a chart.
Is this possible?

if so, then what code should i use?
by Prewest
Sun Oct 25, 2009 6:53 pm
Forum: The Dude
Topic: Probe Thread
Replies: 324
Views: 224383

Re: Probe Thread

probes/functions for HP laserjet printers which warns when the specified toner reaches 15% or less: function: name: toner1 code: string_substring(oid("1.3.6.1.2.1.43.11.1.1.9.1.1")/oid("1.3.6.1.2.1.43.11.1.1.8.1.1"),0,4)*100 probe: name: HP Printer toner 1 available: toner1() error: if(toner1() > 15...
by Prewest
Tue Oct 20, 2009 3:40 pm
Forum: The Dude
Topic: Issue SSH probe commands
Replies: 1
Views: 707

Issue SSH probe commands

Hello, i`m just new to the dude and have a question regarding SSH probe.. on the remote side there`s a linux machine and i need some kind of script to check if an external device there is working. if i log in the linux device with putty i can isue the following command to check the external device: ...