MikroTik

Mapik

Use XenServer 6.5 or newer and it will be OK...

Mapik

Hello, we have problems with OSPFv3 in RouterOS 5.0. It works ok in 4.17 and also i thing 5.0rc5 problem was not here. If connection is established and state on both side become full, there is no problem later, but we have strange problems with connecting. This errors are repeating in LOG: 16:24:42...

Mapik

Hello, we have problems with OSPFv3 in RouterOS 5.0. It works ok in 4.17 and also i thing 5.0rc5 problem was not here. If connection is established and state on both side become full, there is no problem later, but we have strange problems with connecting. This errors are repeating in LOG: 16:24:42 ...

Mapik

Ouh, it's bad ... and some plans to add it into v4?

I thing only per-core load over SNMP ....

We are runing some other proceses on same machine, eg DNS cache, PPTP Server, ..... so this feature will be very useful and I think it schould be easy to implement ....

Mapik

Hi, is there any solution how to monitor CPU load per core ? We have some multicore routers on network and we dont know how big load is really on it, if MT is showing only one value for CPU load...

It can be done eg. over SNMP some way ?

Mapik

Are you sure it is not some kind of bugfix? Ehat problems did you had with 3.30? It seems like rule is not processed .... but counter in mangle is counting packets ... Basicly this works like if we have MSS correction disabled ... so no rewrite in header and users have problems with opening pages f...

Mapik

We want to try new IGP routes aggregation in BGP, but with no success. If we look at "/routing bgp advertisements print" routes are agregated OK here (only 3x /24 per peer). But on peering routers there are ALL routes ... both agregates and original .... (about 250x /32 + 1x /27 + 3x /24) ...

Mapik

We have problems with MT 3.30 and MSS correction on PPPoE... generated rules seems like this: 38 D chain=forward action=change-mss new-mss=1440 tcp-flags=syn protocol=tcp in-interface=<pppoe-elektra-elvis> tcp-mss=1441-65535 39 D chain=forward action=change-mss new-mss=1448 tcp-flags=syn protocol=tc...

Mapik

Hi Mapik, Sorry for the delay but I had a lot of work cut out for me lately. First things first. In bgp you never set the IP of instance to 0.0.0.0 because the router might end up advertising something you don't really want to advertise. In general the router will pick up the highest IP in the stac...

Mapik

I think that RB433 doesn't support voltage monitoring.

If you try
/system health print

there is no info about voltage... on RB333 it is...

Mapik

Thank you for your reply. Our test configuration: /routing bgp instance set default as=1 client-to-client-reflection=yes comment="" disabled=no ignore-as-path-len=no name=default out-filter="" redistribute-connected=no \ redistribute-ospf=no redistribute-other-bgp=no redistribute...

Mapik

We have problem with BGP after upgrade from v.3.7 to 3.10. All routes in /routing bgp networks are not advertised.

Is it a bug? Or we need to change some settings?

Mapik

Is out

Mapik

We have the same problem with one another board from Intel. So we write to Intel Support and answer is, thet on new boards there is no boot support for CF. But in 3.x you can use USB... NO, I didnt have that luck yet. Any version I tried on Intel dg33 motherboards didnt boot. (but it does on earlier...

Mapik

Hello, I have the same problem with 2 RB333 in nstreme-dual, at the first setting they work but after a reboot nothing :( I writed a little script, as sad Mapik, i dont know is correct or not the script, but after that bridge disable/enable still not working. Here is my script: delay 10; inteface b...

Mapik

Yes, we have the same problem on our nstreme-dual bridge with RB333. We temporary fixed it with writing script which disable/enable bridge interface 10s after startup....

Mapik

try disableing periodic calibration... i saw similar problems on a test PtP link in beta 7

After disabling periodic calibration and wmm it works so much better. With power saving set to minimal on my device it works fine. Thank you

Mapik

After upgrade from 2.9.42 to 3.0 beta 10 we have problems with wireless on MDA/PDA devices. Device connect normally but after some time (eg. 1 minute) data don't pass across interface, but it's still connected. If I disconnect and reconnect again, some time everything is ok and then the same problem...

Mapik

add pppoe relay agent this feature will pass pppoe by wlan pseudo bridge not planned at the moment. Why not? It will be really useful for clients who want to dial more then one pppoe connection (eg. some neighbours with two independent accounts) via one wireless device. And it should be easy to imp...

Mapik

I have changed the routerboard on that specific site, was running fine for about 45 minutes then same error again, updated to latest routerOS and same problem, haven't updated firmware as yet. :x OK upgraded firmware to 2.6 on routerboard and still same problem Any suggestions anyone??? :idea: You ...

Mapik

Yes, it will work

Mapik

Some load balancing routing protocol, like olsr will be really useful.

Mapik

please post if you are still haveing issues with RB 153 or post if they have been resolved..i really need a bunch of something with more memory than RB112 and not as $$/powerful as RB532.. im way too scared to order them with all the issues, mainly anything requring a power cycle... tks Wait for RB...

Mapik

Yes, we have also problems with RB153. But RB133 works really fine for us

Mapik

Hi, set some local IP in profile for your PPPoE server ...

Mapik

Multiple cores are supported only in 3.x

Mapik

I use one Sparklan 5213 and one Nortel 5212 cards with RB 153. One bridge, one WDS (16 users) and two wireless clients. After upgrade to 2.9.38 and 2.6 fw, problem with hanging up dispeared, but RB resets in few minutes. I observed that time between resets depends of traffic, so there is memory pro...

Mapik · Yes, after upgrade to 2.9.37 no problems now Thank you

Yes, after upgrade to 2.9.37 no problems now

Thank you

Mapik

We have problems with RB153 too. Tested 18V, 12V, 48V PoE power source, but it's always freezing with 2.9.34 and older. All three board we have were replaced by RB532 and with the same configuration no problems now. So something is wrong with RB153, with 2.9.35 it reboot almost every hour. With 2 ca...

Mapik

Yes, the same problem and also ospf-out filtering not working correctly. Our network downgraded to 2.9.27 and no problems...

OSPF-OUT filter in 2.9.31 fixed and work well. Thank you

Mapik

RSTP already has means to monitor link quality.

We will come with our own better solution instead of OLSR.

Thank you for quick reply. We don't want bridging, but if there will be some solution like RSTP working as routing protocol it will be great. We are looking forward to it.

Mapik

Will be OLSR supported in 3.0 ? It's great load-balancing routing protocol for wireless networks.

Mapik

This will be not supprise me as they will some day disable DOWNGRADE posibility... LOL

But if ospf-out is still not working from 2.9.28 to 2.9.30 what should we do ?

Mapik

Yes, the same problem and also ospf-out filtering not working correctly. Our network downgraded to 2.9.27 and no problems...

Mapik

We have routing filter that doesn't work..........more then 600 /32 route not filtered !!

Also 2.9.30 will ignore framed-route radius attribute

We are using OSPF and the same problem from 2.9.28 to "now"

IN filters OK, but OUT filtering is broken, after reboot all routes go out :-\

Mapik · Will it be fixed in 2.9.31 please ???

Will it be fixed in 2.9.31 please ???

Mapik

Yes, it doesn't work for us too. Some fix for it will be very helpful.

Mapik

I have the same problem with outgoing routes http://forum.mikrotik.com/viewtopic.php?t=10272

Mapik

Maybe you can use two routing marks and then two default routes for this marks with different pref. sources...

Mapik

Please can someone help how to configure ospf-out filtering in 2.9.28 ??? Always not working for us

Mapik

Thank you for your reply Eugene, but it's still not working for us. This is export from one of the MTs... # jan/07/2000 06:16:09 by RouterOS 2.9.28 # software id = 3NQC-3TT # / routing filter add chain=ospf-out prefix=0.0.0.0/0 prefix-length=0 invert-match=no action=accept comment="" disab...

Mapik

We upgraded our networks to 2.9.28 (about 110 routerboards) without problems. But now we see that ospf-out chain is not working. All routers have filter for ospf-in and ospf-out. I install one new today and I forget to set filter. I was shocked if I saw routing table, ospf-out chain is totally not w...

Mapik

We upgraded our networks to 2.9.28 (about 110 routerboards) without problems. But now we see that ospf-out chain is not working. All routers have filter for ospf-in and ospf-out. I install one new today and I forget to set filter. I was shocked if I saw routing table, ospf-out chain is totally not w...

Mapik

sergejs was faster

Mapik

Yes, routing work well with AP-station setting... no problems on 60 wireless routers

Nstream may help with increasing throughput on line... but it need enough CPU power on fast lines...

Mapik

Finally we bought this http://www.intel.com/network/connectivi ... dapter.htm and it work very well

Mapik

We tested the board under FreeBSD and both LANs work fine. In that case it must be the Driver problem, any chance it will be fixed soon ???

Mapik

Is this card functional under MT ???

http://www.intel.com/network/connectivi ... dapter.htm

It's based on Intel® 82571GB Gigabit Controller ...

or which pci-e dual ethernet card will be good for us ?

Mapik

a customer just wrote me: Regarding the Intel chip 82573V/L, it is working just fine with RouterOS 2.9.24. First onboard LAN (82573V) is working very well, but second (82573L) have some big problems... throughput is only about 20Mbit, MAC Winbox and etc is not working... Many many settings we try b...

Mapik

bridge filter may help to filter DHCP packets... and disabled forward on card also...

Mapik

Try disable forwarding on wireless between users and set static ARP and reply only on interface... it may help

Mapik

a customer just wrote me:

Regarding the Intel chip 82573V/L, it is working just fine with RouterOS
2.9.24.

Great, thank you wery much

Mapik

Please, is this 1U server supported by Mikrotik ?
http://www.msi.com.tw/program/products/ ... hp?UID=619

It have one 82537V and one 82537L Intel 1G LAN...

Mapik

Yes, usb boot feature will be very useful... We also need it

Mapik

mapik, write to support. something's wrong in your configuration probably. or maybe there simply are no 2.4 devices in your area (is that even possible?)

Ohh, sorry, it was problem with radio card

Mapik

Any chance for USB boot in the future ???

Mapik

I have problems with wireless scan on 2.4-GHz, can't see networks. In 2.9.20 it's OK

Mapik

It's called CFS (Custom Frequency Select)

Mapik

Let me add another vote for OLSR. Sounds like exactly what we need.

George
1 more from me....

Yes. It will be great if you add it.

Mapik

Realy? It enables internal ftp server on MikroTik IMHO. You dont need this to use ftp inside your LAN. Gotmoh, you're confusing this with /ip service , which indeed controls services on the router itself. --Tom Me confusing? Or Mapik? :twisted: command /ip firewall service-port enable ftp will enab...

Mapik

Normis was faster

Mapik

This problem is almost everywhere in 2.9.21 it will be repaired in 2.9.22 ... see other topics for details. Downgrade eg. to 2.9.18 works well for me

Mapik

I think this may help

/ip firewall service-port enable ftp

Mapik

Please help, which LGA775 board with Intel 945 or E7230 will be good for us ?? Support for on-board LAN, boot from CF-to-IDE, at least 3 PCI slots. Some tested ?? We bought some Intel D945GNTL and it haven't support for CF-to-IDE devices and LAN is not working in MT

Mapik

Intel 82562GX/82562GZ PLC 10/100 Mbits/sec LAN is not supported by new driver ??? We bought new Intel D945GNTL boards because we need 16 wireless interfaces (4x RB14 (x 4 RB52)) but LAN port that we also need is not working :( The board provides one of the following: Gigabit (10/100/1000 Mbits/sec)...

Mapik

Intel 82562GX/82562GZ PLC 10/100 Mbits/sec LAN is not supported by new driver ??? We bought new Intel D945GNTL boards because we need 16 wireless interfaces (4x RB14 (x 4 RB52)) but LAN port that we also need is not working

Mapik

Disable "Default Authenticate" on wireless cards where you need it. It's on tab Wireless. After that only users in Wireless - Registration table can connect.

Mapik

Will be there support for boot from USB in the future??? We bought some Intel D945GNT Boards and it don't support CF-to-IDE drives... Message from Intel: Hello Martin, Thank you for contacting Intel(R) Technical Support. Intel does not recommend the use of CF-to-IDE converters. You are surely free t...

Mapik

USB boot will be really good feature

We now have problems with Intel D945GNT boards that can't boot MikroTik from PATA drives bigger then 8GB (and SATA is not supported by MT, Windows, BSD and others boot fine) and CompactFlash via CF-to-IDE converter is not supported by Intel now

Mapik

You can try this:

/ip hotspot user
pr

set [find] profile=TOPNET352

Mapik

Will be this Planet NIC ENW-9700 (PCI-Expres, 1Gbps) or this HP Broadcom 5751 GB NIC (PCI-E) card good for me ???

Mapik

Is some PCI Express LAN card working in MikroTik ??? Thank you

Mapik

Or do you know some PCI Express LAN card that works in MT ???

Mapik

I have this on-board LAN in our router:
10/100 Mbits/sec LAN subsystem using the Intel® 82562GX/82562GZ PLC device

Is planned support in future releases???

Mapik

It's great to hear it

When it will come ???

Mapik

I use routing-test too. And for PPPoE users I'm routing everything via OSPF, no problems now. And your configuration is almost the same, it must work

But what can you try is to use /30 networks for connecting routers via OSPF... better results for me.

Mapik

After change all areas have all routes from all areas, really long routing tables

but it's not problem

Thank you wery much

Mapik

Oh, thanks, I will try it

Mapik

I try upgrade to 2.9.17 and problem is still here :( Topology is http://www.mapik.net/mikrotik/sferia.jpg If blue/green and blue/yellow routers are 2.9.11 and all others are 2.9.17 everything works. In blue area I can see all routes from all networks and in green/yellow area default route is present...

Mapik

yes, only router that must redistribute between different areas must be 2.9.11 others are 2.9.17 now

Mapik

Upgraded from 2.9.11 and OSPF don't redistribute routes beetween different areas... any change in configuration or a bug ??? It is x86 version Try to change these connection tracking values!!! If problem still persist create another topic with the configuration description! Problem persist :( http:...

Mapik

I have 3 OSPF areas, with 2.9.11 and routing-test everything works great, but after upgrade to 2.9.16 routers stop redistributing routes between areas here is config from one router that may redistribute it... Problem persist with both routing and routing-test... router "see" all routes fr...

Mapik

Upgraded from 2.9.11 and OSPF don't redistribute routes beetween different areas... any change in configuration or a bug ??? It is x86 version

Mapik

Yes, it is

http://www.mikrotik.com/download/router ... 2.9.xx.npk
http://www.mikrotik.com/download/router ... 2.9.xx.npk

change xx to version you need...

Mapik

I have upgraded my 2.9.11 to 2.9.13 and OSPF log is not working now. Problem is with both routing and routing-test.

Mapik · If one is 2.9.11 routing-test and another 2.9.12 routing-test then it's ok

If one is 2.9.11 routing-test and another 2.9.12 routing-test then it's ok

Mapik

If both routers are 2.9.12 with routing-test they can't link using md5...

from log:
header error: authentication type mismatch

many times after Send Hello...

any solution ???

2.9.11 routing-test work fine
Thanks

Mapik

Use 2.9.6 with routing-test... work fine

Mapik

Is Connection Tracking enabled ??? It may be the problem...

Mapik

I upgraded MT from 2.9.6 to 2.9.8 and I can't find OSPF functions in routing-test. I use it for OSPF with filtering in 2.9.6 but now there is only BGP and nothing else... Any ideas???

Search found 90 matches

Re: Can I install Cloud Hosted Router (CHR) on XEN server?

Re: Problems with OSPFv3 in 5.0

Problems with OSPFv3 in 5.0

Re: Cpu load per core question

Cpu load per core question

Re: PPPoE - MSS Correction BUG in 3.30

IGP - BGP aggregation problems 3.30

PPPoE - MSS Correction BUG in 3.30

Re: BGP not advertising /routing bgp networks

Re: RB433AH and voltage monitoring via snmp

Re: BGP not advertising /routing bgp networks

BGP not advertising /routing bgp networks

Re: Need Ver 3.7 ASAP

Re: RC9 Compact Flash not booting.

Re: Nstreme2 with Bridge Interface.... Bug discovered...

Re: Nstreme2 with Bridge Interface.... Bug discovered...

Re: Wireless problems with 3.0 beta 10

Wireless problems with 3.0 beta 10

Routing-test 2.9.28 - ospf-out chain problem

Intel® PRO/1000 PT Dual Port Server Adapter ???

Board Support ???

Which board will be good for us ???

PCI Express cards ???

Support for Intel® 82562GX/82562GZ PLC ???

2.9.16 OSPF redistrubution problem

Routing-test OSPF problem in 2.9.12

What happen with OSPF in routing-test-2.9.8??