another issue... that I created a workaround ppoe client (to the ISP) connects but the route that it is adding is not working... I had to create and run the following script to add a proper route that works /ip/route/set [find where comment="pppoe"] gateway=([:pick [/ip/address/print as-v...
I have two new hAPac^2 and two hAPac. I noticed that in hAPac^2 the full size of HDD is not 16MB, but 15.3MB !!! On these devices HDD and so very small, why make it even smaller?
It's strange, but I see only two antennas, and the block diagram shows 4 antennas. For the first time I see that Mikrotik would use dual-band combined antennas. How do the transmitters not jam the receivers of the other range, while maintaining a decent sensitivity?
My story ended happily! I wrote in support that after the replacement of NAND the license was lost and attached the photos: 1. RB493G_SerialNumber.png - the photo of my Routerboard with the serial number and both the old and the new NAND chips; 2. RB493G_Winbox.png - the detailed information about [...
Everything is bad! My RB493G worked for 5 months, scored 30% of bad blocks and stopped working, when I updated RB. Even Netinstall does not help. I bought a new NAND, replaced it and the router worked perfectly, bad blocks no longer appear !!! But I lost the license !!! Router will stop functioning ...
!) detnet - implemented "/interface detect-internet" feature; https://wiki.mikrotik.com/wiki/Manual:Detect_internet I enabled the detection for "all" interfaces on a CHR test system that has 2 ethernet interfaces Another issue: although the interfaces have been setup with static...
Please use Netinstall to upgrade your router (install 6.38.7), upgrade RouterBOOT by /system routerboot upgrade and /system reboot. Make sure not to write logs to disk. Let us know about the results. I did it all. Bad-blocks 0,0%. [admin@MikroTik_RB493G] > system resource print uptime: 6m version: ...
This is an ordinary home router. It has two R52n-m cards and give out Wi-Fi 2,4Ghz and 5,5Ghz. He does not write anything to the NAND.
I have RB493G one year. I got it not new and I do not know its history.
Can this NAND be replaced? Should it be clean or it must be programmed beforehand?
I have a problem with latest 6.38rc build when I try to update Mikrotik hAP lite (RB941-2nD).When the upgrade is finish and router reboot I can't connect to the router anymore. No wireles signal and no neighbors mac address.The only way is netinstall.Does anyone have the same problems because I nev...
I have two hAP lite. On both routers after update from v6.37.1 to v6.38rc19 and after each reboot I am see in Log "system, info, critical --- CPU overclocked", but in system, resources all O.K. [Guess_Who-2@MikroTik] /log> print 15:29:59 system,info installed dhcp-6.38rc19 15:29:59 system,...
same voltage sensor as problem as above Voltage reading shows 16V PSU is at 24 V (measured) Can this be fixed with software or do I need to RMA ? What's new in 6.36rc13 (2016-May-17 12:20): *) dude - (changes discussed here: forum.mikrotik.com/viewtopic.php?f=8&t=108083 ); *) dhcpv6 client - fi...
I bought the new "Router Board MikroTik hAP ac" via eBay. I have installed the latest stable version of RouterOS right away (all_packages-mipsbe-6.35.zip and firmware 3.31), default configuration. Health is showing 16.1V voltage. I then took the power supply from RB450G, but Health was sti...
My RB450G + ROS v3.30 work very good. When I installing total packages v4.3 do not work all ethernet ports. If I disabled ipv6-4.3.npk, all ethernet ports begin to work, bat if I change names or MAK-ADDRESes of ethernet ports and reboot router, first port not storred changes.
*) fixed problem - RB450G ethernet did not work if one of the ports was disabled; *) fixed ethernet of RB433 with switch chip IP175D; *) fixed route attribute problem; *) fixed route next-hops falling under multiple connected routes; Hi Normis, It seems that not all the issues of RB450G ethernet sw...