LOL, reading this topic (and reading changelog) is so funny...

Ohh..,. we got layer7, GREAT, but wait, wait, what is that - how do we use that??? Where can we find a info about that? Any one can help us? Any one researched how do we use this?

LOOOOOOOOOL

[...] so steps to perform: 1) install newest RouterOS version, other way all the complaints will be rejected by devs as - this is old version 2) try to check if everything is ok with configuration (double check everything) 3) try to reproduce the bug if you succeed write down how you done that. 4) ...

"Stop consuming our time. If you think nobody should use OSPF on 2.9.43
talk with facts "

Talking facts, yeah... My reply was deleted not first time, so anything I can tell is GOOD LUCK & HAVE FUN !!!

Other folks are complaining that OSPF is flakey with 2.9.43 and routing-test OSPF flakey? Are you sure? Where you readed about this? That must be your imagination... LOOOOOL :evil: Have it running on 3 boxes on different possitions of my net for 3 weeks now without problems. All that 3 boxex runing...

I have 100 devices in v2.2 in my home computer athlon x2 3800 1gram, i'am barrely noticing dude existance..., just box need to be rebooted after 2-4 days if i need extra ram because there is probably little memory leak...

Any one can say anything about 2.9.43 vs 2.9.37 ?

We have started upgrading to 2.9.42 some time ago, but more stuff upraded more problems, and finaly we were forced to downgrade to 2.9.37 as ospf just stopped to work definetly. Any news in 2.9.43 ? Maeby some statement from mikroik?

Yes, you are 100% right, my mystake - we are using 2.9.27 too.

40 routers, 600-1000 entries distributed by ospf.
From time to time, dynamic routes just disapear from ip route table.
There is no problem in 2.9.28.

Sending alone anythink to support is worthles - so anyone have this problem too?

dude, running routing daemons on an RB112? Are you kidding me?
[...]

This was just example of the CPU utilization problem with routing-test.
We have just bought 5 of them for tests, and everyting that is needed to RB112 die is just enable OSPF on it and connect to the network

Maeybe you just want to have access to rb112 with regular package and without?

I think .28 .29 were send to suuport, but I'll check it.

Ospf in routing test in .28 .29 is very broken.
Also in - lets say - stable .27 ospf uses much more cpu than regular routing package, as much more as RB112 cant handle ospf (30-40 routers, 1000 /32 routes) with test package.

beta 4 - problem still exists.

I disabled 2000x2000 pixels image, and there is no problem now.

But, in other hand, clicking "setting" ~50 times will cause 10MB memory use (task manager -> memory usage).

I can confirm that problem exist, some memory leaks. Clicking settings cause 10-50 MB memory corruption per click, or smetimes constant memory usage increase untill all memory is full, then crash. In my case It have to do something with device -> services -> ping. Only 3 devices, empty submap, and 2...

1TB ofcorse

There are solutions, but its very costly, one wchich i know cost about $50k for 50Mbit traffic and 1GB storage capacity.
Just use google.

2.9.13 routing-test ospf broken too. Sometimes routers "disconets" for a few seconds with something like "re-start" status in ospf-> neihgbour -> print

We are here use only ospf - 2.9.11 (2.9.12 winbox crashing too often, 2.9.13 caused once kernel panic on upgrade).

OSPF work, but as you say, sometimes ospf hangs (one area with routing-ospf and one with regular routing).

yup, x86, uploaded, rebooted, kernel panic, "attempt to kill init", used netinstal to rebuild with 2.9.12, uploaded 2.9.13, reboot, now all packages enabled (wireless, w-legacy, routing, routing-test, ...). Now going to disable unwanted packages...

2.9.12, as you can see 7 in 10mhz vs 13 in 20MHz 0 interface-type=Atheros AR5213 chip-info="mac:0x5/0x9, phy:0x43, a5:0x36, a2:0x0, eeprom:0x4008" pci-info="01:03.0" capabilities=tx-power-control,ack-timeout-control,virtual-ap,alignment-mode,noise-floor-control,scanning,burst-sup...

I wonder why I get less channels avaiable in 10Mhz than 20MHz mode.
A bug?

Thx for the explanation of the problem.
I was asking support for months without success, why is ospf sometimes hangs betwen routers. It's look like there is only hope with new route package.

I had the same problem. Downgrade to 2.9.8 solved this.

lol ))
This simply mean as it is writed in the log - "POOL IS EMPTY" - no free addresses are left to give to customers

Increase you address space or lover lease time.