MikroTik

pikpik

https://help.mikrotik.com/docs/display/ ... p+features

??

pikpik

Sorry. This is my diagram

https://imgur.com/x4lohJj

pikpik

search the two guide on forum, and read mikrotik help

i can't find for my case.

pikpik

I can confirm:

[…] everything is wrong, you have made all virtual vlans, instead of letting the bridge manage the vlans […]

what do i need to change for the vlans to work in hardware?

pikpik

When you need to repair your car, do you take the photos to the mechanic? From the photos, how can you see how the device is configured? Apparently everything is wrong, you have made all virtual vlans, instead of letting the bridge manage the vlans. That's a switch, not a router (and probably is th...

pikpik

RB: CRS309-1g-8s+

Config: default + a few vlans (30) , one bonding interface, 2x bridge. no filters and no fw rules.
Traffic : ~1Gbps ~ 80k pps

More info on screens.
https://imgur.com/a/I0jNdNa

Fast forward enabled on bridge, hw offlowading on ports and vlans. What am I doing wrong ?

pikpik

Hi
When i change default ip to static CSS stops responding to pings, web ui too. It works fine when i use dhcp or default ip.I see in winbox that ip is changed. When I plug in directly to my laptop it's response fine.
Where can i set up default gateway ?

pikpik

bump!

pikpik

Has anyone tried set up qos for geforce now service ?

pikpik

Thank you, that works!

pikpik

Interface vlan works just fine for me. Don't know why eoip/vpls cousing loop. But i have another problem default-forwarding=no and i can mac-ping clients on AP. Is that normal ?

pikpik

Unfortunately, it did not help :/ Still loop after adding to bridge

pikpik

just remember that rstp can be forwarded from another device. It can be identified as having DST mac 01:80:C2:00:00:00 / 01:80:C2:00:00:08

Can you show me example of your filter rules ?

pikpik

I'll try the same conf with vpls and rtsp disabled.
Edit. effect is the same - loop

pikpik

Guys please tel me why ? It's local loop. On far end eoip not in bridge.

pikpik

How about Windows version ?

pikpik

Guys, which devices are best for PtMP ?

pikpik

Waiting 30mins with status "detecting radar", wtf MT ?

pikpik

Hi Guys,
Can you recommend any free net-flow collector for Mikrotik traffic-flow ?

pikpik

How to get information such as right side od picture ?

pikpik

Thanks for answer

But still i dont know how to run mass command execute ie.

/system identity set name=

pikpik

Hello,

How can i massively execute command via Dude on devices (RouterOS) ? I need to upgrade firmware (bios) on 1000+ devices. It is possieble ?

pikpik

status: radar-detecting channel: 5640/20-eC/an/DP (3440) noise-floor: -111dBm authenticated-clients: 0 current-tx-powers: 6Mbps:19(19/22),9Mbps:19(19/22),12Mbps:19(19/22),18Mbps:19(19/22),24Mbps:19(19/22),36Mbps:16(16/19),48Mbps:14(14/17), 54Mbps:13(13/16),HT20-0:19(19/22),HT20-1:18(18/21),HT20-2:1...

pikpik

What is 9abe protocol ? How to drop it on bridge ?

pikpik

Solved but LOL

pikpik

:if ([/ping 8.8.8.8 count=5 routing-table=WAN1 ] = 0) do={
/ip route disable [find where comment="Brama_domyslna"]
}
else {
/ip route enable [find where comment="Brama_domyslna"]
}

syntax error (line 4 column 6)

Why syntax error ? I also tried

else={

CRS125/ROS 6.36

pikpik

Then you for help but still no luck with this configuration:/ How can i connect to wlan2 with station pseudobridge ?

pikpik

I can't do anything with modes on gopro it must be ap mode

pikpik

Hello I know it's not a MT problem but maybe someone can help me with this. Devices: Repeater - RBMetal2SHPn AP - Gopro Hero 3 black Client - Android 6 phone Diagram: GOPRO ( dhcp server over wifi ip 10.5.5.9) -> RBMetal2SHPn ( wireless-rep ros latest stable) wlan1 main radio station mode , wlan2 vi...

pikpik

Can you give me your best settings for omnitik without nv/nstreme for band a/n.

pikpik

Change wlan card.

pikpik

Torch on screen. Not all clients have MT device.

pikpik

Hi gouys Frist simple diagram INTERET ---- > PPPOE SERVER (Linux non ROS) --> SIMPLE SWITCH --> RADIO-A --- transparent bridge ---> RADIO-B --ethernet--> OMNITIK ------> Clients Problem: I have some loop on client WDS's at Omnitik. Non wds client havent't this problem. Look at screen. Ethernet traff...

pikpik

http://elceef.itsec.pl/mactelnet/

pikpik

SOLVED!

It's pppoe traffic. On station side in torch i see pppoe traffic ( the same as the bridge side ), but on the side of the bridge is seen as protocol 32 - i don't know why. I think is ROS bug. This should be protocol 34916 (pppoe) not 32.

Thx for help CelticComms. karma for trying :>

pikpik

It's dec (32 MERIT-INP MERIT Internodal Protocol i think ). no vpn traffic. This is what I observed: I see this traffic on all MT devices with wlan (MP or PtP). But i think its caused by ap-bridge with clients. On AP have few UBNT devices and some else i.e. CA8-4, RB etc. When i disable all of UBNT ...

pikpik

I have simple bridge and all interfaces in bridge port (3xeth 1x wlan(ap-bridge with some clients)). When i run torch command via wlan i see traffic on protocol 32 ~12mbps/~500pps. One ethers nothing. It is possible to block them on wlan interface?

pikpik

is this correct? /interface bridge settings set use-ip-firewall=yes use-ip-firewall-for-vlan=no /ip firewall filter add action=drop chain=forward comment="" disabled=no protocol=32 or /interface bridge filter add action=drop chain=forward comment="" disabled=no mac-protocol=0x20 ...

pikpik

hi guys

how can i drop packets over protocol 32 via bridge filter ?

pikpik

How can i change port name or add some description to port ?

pikpik

Hi guys!

Can you tell me how to block smurf & fraggle attacks on MT ?

pikpik

What kind of tunnel use in PTMP on nv2 ? WDS is working fine ?

pikpik

SOLVED. In my case, this interferences were but in my opinion ping times are higher than on nstreme.

pikpik

Hello RB433 <<=====2km=====>> RB433 Linki info: status: connected-to-ess band: 5ghz-n status: connected-to-ess band: 5ghz-n frequency: 5240MHz wireless-protocol: nv2 tx-rate: 300.0Mbps rx-rate: 300.0Mbps ssid: to_radiob signal-strength: -57dBm signal-strength-ch0: -67dBm signal-strength-ch1: -58dBm ...

pikpik

hmm why in MT are different rates ? mcs0 - 6.5mbps ? in cisco 7mbps ? am i wrong ?

pikpik

can you give me table with rates : mcs-x ---- rate

pikpik

I try today on ~12 km. Will show you results.

gringoZ : try change mtu /mpls interface set 0 mpls-mtu=1526

2jarek: i only try iprove his link

pikpik

eeh ..
1. Run test over vpls (test to ether ip - not transport/remote/wlan ip )
2. Test run on ROS not on pc with winshit

pikpik

on N use chains

pikpik

tcp test plz:P try change band to only-n. Show me wireless advanced (all hw cvars)
edit:
OMG use VPLS !!!

pikpik

show me test MT-MT on this settings. (not pc pc). Try add ht-extension-channel= .

pikpik

CPU overloaded and vpls doesnt work on your. Try to send traffic over vpls.
When you use vpls, decrease CPU usage and throughput will improve.

pikpik

mee to

pikpik

I have the same issue, reset helps me, dont know why. Those setting works fine on ~3km. Just try. I have 4.5

pikpik

Is this possible ?

pikpik

hw-retries=15, try to set only few mcs rates. Disable a/g rate. If doesnt help, try reset-conf (with bios upg) and use this settings: ack-timeout=dynamic adaptive-noise-immunity=none allow-sharedkey=no \ antenna-gain=0 antenna-mode=ant-a area="" arp=enabled band=5ghz-onlyn \ basic-rates-a/...

pikpik

pikpik

syntax errors on v4.5

pikpik

anybody ?

pikpik

Ohh ill see

http://mum.mikrotik.com/gallery/v/PL10/ ... 2.jpg.html
What brand are these antennas?

pikpik

beer beer , only beers. Where are the girls, guys ?

pikpik

Nstreme work's fine uffff.

What i do:

RB 433 3.25 > 4.6
reboot
upgrade
reset
reset (after 1st reset)
reset cards
N config from wiki (optimal)

Nstreme is stable.

When I upgreaded form 4.2>4.3>4.4 etc. without reset nstreme was unstable.

pikpik

802.11n speed is limited over WDS bridges, this method doesn't have such limitations

MT Wiki

Try http://wiki.mikrotik.com/wiki/Transpare ... using_MPLS

pikpik

heh ... wds doesnt work fine on N. So it makes no sense to compare.

Eoip vs vpsl in real link (about 40mbps real tcp) its 40% cpu save on my

pikpik

with nstreme ? max bandwidth ?

pikpik

where i can set rts/cts ?

pikpik

NSTREME: status: connected-to-ess band: 5ghz-11n frequency: 5600MHz tx-rate: "78.0Mbps-HT" rx-rate: "65.0Mbps-HT" ssid: "router-lv" bssid: 00:1D:0F:XX:XX:XX radio-name: "001D0FXXXXXX" signal-strength: -48dBm tx-signal-strength: -50dBm rx-ccq: 43% p-throughput:...

pikpik

I need best settings for ap on 2.4g. ~max 20 clients peer ap (randomly) Max transfer peer client 512/512kbps. I have B/G cards. The best settings that I managed to achieve : 0 R name="ap_xxx" mtu=1500 mac-address=00:02:6F:xx:xx:xx arp=enabled disable-running-check=no interface-type=Atheros...

pikpik

RB433 + ROS 4.5 + R52N + AirMAX Sector 16/120(2pol) 2 connectors plugged into card. I have clients A only but in the future will also in N. name="ap_xx" mtu=1500 mac-address=00:0C:42:XX:XX:XX arp=enabled disable-running-check=no interface-type=Atheros 11N radio-name="000C42xxxxxx"...

pikpik

can you test it with nstreame ?

pikpik

wds is working fine on N ?
no that not suported ,

i hawe link ower ~2km

routerboards is rb433 (300mhz) and r52n cards , use 17 dbi patch antenas 1X

signal -70... -68 and signal to noise ~40db , i use vpls

tcp traffic over 30-40mb half duplex .

with nstreme ?

pikpik

wds is working fine on N ?

pikpik

tcp or udp ?

pikpik

cool! do you have any traffic running on it? what throughput do you get in both directions? at this moment, i have only RB433 and i'm waiting for AH. Daily i have 30mbps/12mbps with ~6000-8000 pps. I added to this traffic bandwidth-test (TCP 50 conns) and received additional 10/10 mbps (but cpu 100...

pikpik

exe: status: connected-to-ess band: 5ghz-11n frequency: 5600MHz tx-rate: "270.0Mbps-HT" rx-rate: "270.0Mbps-HT" signal-strength: -54dBm tx-signal-strength: -56dBm noise-floor: -113dBm signal-to-noise: 59dB tx-ccq: 97% rx-ccq: 87% p-throughput: 140175 overall-tx-ccq: 97% authentic...

pikpik

.

It is not fair to compare this to dual nstreme as currently 802.11n doesn't work with nstreme.

Work's fine, have N link with nstreme. ~3km

pikpik

vpls + nstreme on 4.5 works fine
eoip or wds + nstreme = disconnects

pikpik

I have troubles too :/ http://forum.mikrotik.com/viewtopic.php ... 09#p189909

pikpik

can anybody upload it on another mirror ?

pikpik

Hello Conf. AP # jan/02/1970 01:30:48 by RouterOS 4.5 # software id = RGKP-MP7S # /interface wireless security-profiles set default authentication-types="" eap-methods=passthrough group-ciphers="" group-key-update=5m interim-update=0s management-protection=disabled management-pro...

Search found 80 matches