Trace route traces routers, hops.... So since we see the same IP twice obviously there is a routing loop there for some reason... By the way, tracert works in the following way: You try to trace route to 1.1.1.1 So your router sends a packet with TTL=1 The first router drops it because it will decr...
I am running a tracert to 1.1.1.1 and as soon as it leave my network I get 2 IP's that are the same back to back on my upstream providers network.
what would cause this to happen? Hops 3 & 4
ok, I have a Cable modem at a site and I want to tunnel it to one of my fiber locations for BGP advertisement purposes since I can not do BGP on the cable modem. So basically I want it to become a shorter router through the tunnel for my traffic and it to come in the fiber DMARC and then go back out...
I know this is an old post but this would be a very handy feature as described above. I have been asking for this for several years now as we have submaps in our main map of different network on it. If a submap within those turns red from down devices it would be nice if the main submap turned red ...
I know this is an old post but this would be a very handy feature as described above. I have been asking for this for several years now as we have submaps in our main map of different network on it. If a submap within those turns red from down devices it would be nice if the main submap turned red s...
mschreiner - so your request would be to create hierarchical map structure with parent/child map tree structure ? Where parent map notifies about all issues on their submaps ?
I have noticed the same issue! Also, I would like to see a feature where if a Submap with Devices is within a Parent submap with no devices that the parent would turn red as well depending on the submaps within it. This Allows me to have a main page broken down to multiple areas on my network. Would...
ok, I have had some strange things happening and trying to figure out where the problem lies. We are running our Dude on a virtual server in our office and we run a WISP OSPF network. The problem I have had the past few months is the ping service turns red on a few routers but I can still get into t...
You will need to have route in each router pointing to the other subnet. Hm... he runs the AirRouter in SOHO mode (NAT), so this won't work. If he would route it, you were right. 192.168.253.167 should already be able to access 192.168.1.0/24 since you are running the AirRouter in SOHO mode. It's j...
Hello, I have been trying to setup up some nat rules to be able to RDP from one subnet to another. Here is my setup. My office is on a 192.168.1.0/24 network on ETH4 of our RB1200 I have a ubnt air router in our techroom that is set in SOHO mode. It has a static IP set to 192.168.1.121 on the WAN an...
mschreiner Could this problem be power related? Are you able to feed the card with additional power by possibly soldering fat wires? And upgrading the power supply.. ? Just a hunch. I do not think it is power related. We are running a 48v power supply too all of our towers. The towers having issues...
Hello, I have rc7 installed on a RB433ah. I am running an XR9 in NV2 with MiKrotik Clients. 23 clients on the tower. The problem I am seeing is my active connections are dropping and they do not come back until I cycle the wireless card. As soon as I cycle it they come back for awhile and then it al...
Signals are: -63 & -62 Tx/Rx CCQ: hovering around 90/97% to 98/100% signal to noise is 40 dB P Throughput: 30502 kbps RB433AH 1 R52H card connected to a Rootena 5.8 22db panel 1 XR9 card conected to a 900mghz Omni The other end is a RB433AH 1 R52H card connected to a Rootena 5.8 22db panel I did...
Hello, I have recently added a 5.8 backhaul and I am having very low bandwidth testing. I have one 5.8 set to AP bridge with nstreme on and the other set to station pseudobridge with nstreme on. The link is maybe 3-4 miles in distance. If I do a udp bandwidth test I get around 2.5 Mbps on the Tx and...
Hello, I am setting up a repeater and everything seems to be setup right but I can not get my client CPE to Authenticate via Radius through the main tower. Here is how I have configured my setup. We build a unit with a 433AH and duel Air cards (R52H/XR2) R52H is my master connectin to my tower in St...