Can not install MTU on lte. After reboot, the setting is reset. Device Information: [admin@MikroTik] > /system routerboard print routerboard: yes board-name: LtAP mini model: RB912R-2nD serial-number: 8F0009454CC4 firmware-type: qca9531L factory-firmware: 6.42.1 current-firmware: 6.42.6 upgrade-firm...

I have problem with bonding
http://forum.mikrotik.com/viewtopic.php?f=2&t=115951

After updating routeros traffic incorrectly balanced. /system routerboard print routerboard: yes model: CCR1036-12G-4S serial-number: 56060492EDC1 firmware-type: tilegx factory-firmware: 3.18 current-firmware: 3.33 upgrade-firmware: 3.33 /system resource pr uptime: 1d20h36m6s version: 6.36.4 (bugfix...

How to explain that the old protocol nstreme efficient than a new nv2 (tdma)? Band 5 Ghz, width 10 Mhz, ideal conditions, lack of interference. /interface wireless set [ find default-name=wlan1 ] adaptive-noise-immunity=ap-and-client-mode band=5ghz-onlyn basic-rates-a/g="" channel-width=10...

All CPE must have the same preshared key. How to control access?

EAP-TLS to implement the protocol NV2. How is this possible?

I have a lots of nstreme links running on v5.11 without problems. When I have extensive data loss on nstreme links it is always from another wireless link running on the same frequency or very near it. I've noticed that nstreme is highly unstable if it shares frequency, but very good if you move to...

Downgrade to version 4.17 has solved the problem.

Let me know who has what version (5.x) of nstreme working properly!

Sorry for bad english. I have а problem - does not work Nstreme under ideal conditions. And the link works fine in the modes of 802.11 and NV2, mode Nstreme low ratespeed and disconnects ("extensive data loss"). 802.11 mode: /interface wireless registration-table> print stats 0 interface=w...

From WIKI:

Nv2 protocol implementation status
As of version 5.0rc3
RADIUS authentication features

How to manage the media access?

Whether there is support in the nv2 security profiles and radius authentication (EAP)?

We are forced to use the CPE UBNT Nanostation because they support the protocol EAP-PEAP-MSCHAPv2

http://code.google.com/p/linux-eoip/

svn checkout http://linux-eoip.googlecode.com/svn/trunk/ linux-eoip-read-only

Its work

Disabling the ht-basic-mcs rates.

I need to deny 802.11b rates, and allow only 802.11g and 802.11n rates. My config: name="wlan1" mtu=1500 interface-type=Atheros 11N mode=ap-bridge ssid="test" area="" frequency-mode=manual-txpower country=russia antenna-gain=0 frequency=2472 band=2ghz-b/g/n scan-list=de...

The problem was in the driver. Had to replace the Intel to Realtek.

I've got a similar problem when using the client adapter TP-Link TL-N821N. In 802.11N mode after the association does not go to traffic from a subscriber to the base station. The problem in the drivers - if the client uses Windows 7, there is no problem, if XP - then the adapter works only in 11b/g ...

The bandwith in WDS (ap bridge/wds - ap bridge-wds) mode is much less than in the mode of the ap bridge/station. When will it be fixed? I dont think it can be fixed, you are splitting radio time 50/50 between AP and STATION. If you make it station its 100% dedicated to connecting to AP, if it's AP ...

The bandwith in WDS (ap bridge/wds - ap bridge-wds) mode is much less than in the mode of the ap bridge/station. When will it be fixed? VPLS not offer as WDS need to MESH.

I have the same problem. I am in despair. Return the device to the seller?

I have seen this problem in versions 4.9, 4.10, 5beta.

Hmm, here the same problem:
http://forum.mikrotik.com/viewtopic.php ... 06&start=0

Sorry for bad English With the loss of adjacency with the neighbor (no longer receives hello packets due to disconnection) Mikrotik removes the active routes from the kernel, but does not delete the LSA from the base OSPF. In some cases this leads to a routing loop. Example: network --- neighbor1 (a...

Topology: RB433-mesh1(00:0c:42:43:43:47)-ether1---(access vlan100)(Cisco c3750)(trunk)---ether1-vlan100-mesh1(02:e3:9e:c4:37:f1)-x86 Configuration on x86: [admin@MikroTik] > interface ethernet print detail Flags: X - disabled, R - running, S - slave 0 R name="ether1" mtu=1500 mac-address=0...

In v4.9 field is not present

Required to effectively manage and filter traffic subscribers isolation on layer 2.

what version do you use? for me v4.2 and v4.6 works fine

I use 5.0beta2. Please show an example of removing the route using an API.

How to remove a static route using API? Example: ip route print where dst-address =192.168.153.2/32 Flags: X - disabled, A - active, D - dynamic, C - connect, S - static, r - rip, b - bgp, o - ospf, m - mme, B - blackhole, U - unreachable, P - prohibit # DST-ADDRESS PREF-SRC GATEWAY DISTANCE 1 S 192...

For hwmp+ all routers should work in the mode of ap-bridge + wds dynamic (or static) mesh. In this mode, the TX/PX rate does not exceed 54Mbps. Bandwidth does not show more than 23 Mbit/s. When you switch to one of the points in the treatment station or station wds these problems are solved (the poi...