Community discussions

MUM Europe 2020

Search found 36 matches

by spammyduck
Sun Nov 11, 2018 7:41 pm
Forum: SwOS
Topic: CRS317 boot issue after power failure
Replies: 22
Views: 3444

Re: CRS317 boot issue after power failure

"And under Changelog: What's new in v2.9: *) CRS326 & CRS328 & CRS317: make sure that RSTP BPDU packets are always untagged; *) CRS328-4C-20S-4S+: make 1G fiber SFP modules work;" I'm seeing the same thing on my switch currently running v2.8 . That post was from Sept of this year, I would very much ...
by spammyduck
Sat Nov 10, 2018 10:35 pm
Forum: General
Topic: 1Gb SFP problems with CRS326 and CSS switches
Replies: 0
Views: 386

1Gb SFP problems with CRS326 and CSS switches

I have two CRS326-24G-2S+RM running RouterOS v6.43.4 using Generic FS.COM 1Gb FSP ( FS P/N: CWDM-SFP1G-ZX ) . When there is no link (fiber not plugged in) the switch sees the SFP and all the SFP info is there. There is nothing connected to the switches other than each other and me at one end (tried ...
by spammyduck
Sun Jun 24, 2018 6:35 pm
Forum: General
Topic: PPPoE MSS clamp no working on upgrade
Replies: 17
Views: 5486

Re: PPPoE MSS clamp no working on upgrade

So was anything ever resolved or figured out on this ? We had an x86 v6.32 ROS PPPoE (MSS Clamping default on server so no mangle/firewall rules at all and disabled on client edge devices) that ran amazing until the server suddenly died. Replaced it with a CCR v6.42.2 and clients with edge device se...
by spammyduck
Sun Jun 17, 2018 8:40 pm
Forum: Beginner Basics
Topic: Does it matter what port is Role Root ?
Replies: 4
Views: 1137

Re: Does it matter what port is Role Root ?

Sooooo if port 1 is the only port that any of the other ports ever need to talk to , should Port 1 be the root ? Does it matter ? Should it matter to me which port is root ?
by spammyduck
Sun Jun 17, 2018 4:45 pm
Forum: Beginner Basics
Topic: Does it matter what port is Role Root ?
Replies: 4
Views: 1137

Does it matter what port is Role Root ?

So before updating my switches I did not use bridging, just the master/slave port setup. My network is very flat/switched, no vlans , nothing but switches until it converges on the core CR switch (3 ports, port 24 all 700 hosts- port 23 connected to 10.10 on router, port 22 connected to PPPoE route...
by spammyduck
Sun Jun 17, 2018 4:08 pm
Forum: General
Topic: Auto Isolate Toggle in Bridge Port
Replies: 1
Views: 1897

Re: Auto Isolate Toggle in Bridge Port

I have been searching for the answer to this question also. Every "how to" I find on setting up Split Horizon says to enable "auto isolation". Also everything I find is pre 6.4 and now the "auto isolate" has been moved to a new tab "STP" that did not exist previously. Is the the function of Auto Iso...
by spammyduck
Sat Jun 16, 2018 5:52 pm
Forum: General
Topic: Did recent updates break Path MTU discovery ?
Replies: 1
Views: 683

Did recent updates break Path MTU discovery ?

I have 13 wireless PoPs and a small fiber to the home deployment (about 100 customers on the FTTH). All 13 wireless pops consist of several AP's all connected via Ethernet to a CCRSwitch. Port one of the CCRSwitch is always the Backhaul radio. Near our NOC is a tower were all of the wireless comes t...
by spammyduck
Tue Dec 20, 2016 4:50 pm
Forum: Beginner Basics
Topic: Interim Accounting packets with FreeRadius and PPPoE
Replies: 3
Views: 1119

Re: Interim Accounting packets with FreeRadius and PPPoE

I have scoured the web, freeradius manual, and mikrotik manuals for weeks looking for how to enable/disable interim packets on router OS. For weeks I went back and forth with our accounting software's tech support and even consulted with a supposed Mikrotik guru on how to make a mikrotik send interi...
by spammyduck
Sun Dec 18, 2016 11:51 pm
Forum: Beginner Basics
Topic: Interim Accounting packets with FreeRadius and PPPoE
Replies: 3
Views: 1119

Interim Accounting packets with FreeRadius and PPPoE

PowerRouter running v6.22 650+ PPPoE clients/connections FreeRadius http://imgur.com/a/nDpRF Everything works great except that the Mikrotik does not appear to be sending Interim Accounting Packets. I'm having trouble getting radius accounting working, it doesn't appear that the Mikrotik is sending ...
by spammyduck
Mon Jan 25, 2016 6:21 pm
Forum: Beginner Basics
Topic: Winbox 6.22 login is off the screen windows 10
Replies: 4
Views: 1020

Re: Winbox 6.22 login is off the screen windows 10

That did the trick. Apparently the logon box doesn't cascade or stack but doing Move and using the arrow keys brought back onto the screen.

Thanks
by spammyduck
Fri Jan 22, 2016 6:15 pm
Forum: Beginner Basics
Topic: Winbox 6.22 login is off the screen windows 10
Replies: 4
Views: 1020

Winbox 6.22 login is off the screen windows 10

We use winbox on several computers here and until just yesterday it was working fine on the PC with Windows 10 on it. However all of a sudden when you open winbox the login box you would normally see appears to open up off of the screen where you can't see it at all. If the login box has focus I can...
by spammyduck
Sun Aug 30, 2015 12:21 am
Forum: Beginner Basics
Topic: Is this possible ? 3 PPPoE clients 3 ports
Replies: 3
Views: 615

Is this possible ? 3 PPPoE clients 3 ports

I have an RB2011 and 3 host machines. Port six is connected to a PPPoE Server I would like ports 7, 8, and 9 to each have their own PPPoE connection (each one will have a different username and password) and provide NAT/DHCP to whatever it plugged into each of them.

Is this doable ?

Thanks
by spammyduck
Tue Apr 21, 2015 7:16 pm
Forum: Beginner Basics
Topic: Firewall rule not stopping tcp port 63000
Replies: 5
Views: 969

Re: Firewall rule not stopping tcp port 63000

No the 181.1 address, while a public IP, is on the local side of our router out of Port 3. Port 1 is our Internet connection it is a /29 Port 2 is a 180.0/24 Port 3 is a 181.0/24 Port 5 is a Mikrotik PPPoE server with IP's 182.0 to 183.255 Port 7 is a local 10.10 management network. With that rule a...
by spammyduck
Tue Apr 21, 2015 6:46 pm
Forum: Beginner Basics
Topic: Firewall rule not stopping tcp port 63000
Replies: 5
Views: 969

Firewall rule not stopping tcp port 63000

Hello, Initially I created the rule pictured as chain=virus. As far as I can tell all the other chain=virus rules are working correctly with the action=jump chain=virus rule. When we discovered the rule was not stopping incoming tcp port 63000 traffic I changed it from chain to forward and made it r...
by spammyduck
Wed Feb 18, 2015 12:43 am
Forum: Beginner Basics
Topic: Help understanding MikroTik "SWITCH" behavior using Maser/Slave
Replies: 2
Views: 760

Re: Help understanding MikroTik "SWITCH" behavior using Maser/Slave

I've spent a lot of time on that wiki page before I ever posted here and either it doesn't have the answers to my questions or I'm just not understanding it.
by spammyduck
Tue Feb 17, 2015 11:28 pm
Forum: Beginner Basics
Topic: Help understanding MikroTik "SWITCH" behavior using Maser/Slave
Replies: 2
Views: 760

Help understanding MikroTik "SWITCH" behavior using Maser/Slave

Hello, I have gone through many posts and found many explanations on how the switch ships on the Mikrotik switches work but I'm still not able to wrap my mind around exactly what Master / Slave does. I have a couple of RB2011 Mikrotik routers that I have been working with and I'm completely confused...
by spammyduck
Wed Jan 28, 2015 5:46 pm
Forum: Beginner Basics
Topic: Accessing management interface on mikrotik SWITCH.
Replies: 6
Views: 3611

Re: Accessing management interface on mikrotik SWITCH.

Thank you, that did the trick.
by spammyduck
Mon Jan 26, 2015 5:48 pm
Forum: Beginner Basics
Topic: Accessing management interface on mikrotik SWITCH.
Replies: 6
Views: 3611

Re: Accessing management interface on mikrotik SWITCH.

Well this just keeps getting more and more confusing. I was told in another post that I could not use the settings that are specifically for routing (uses the cpu) and the only settings that will work are the ones that only use t he switch chip. Isn't a route, routing ? Do I have to remove a port fr...
by spammyduck
Sun Jan 25, 2015 7:00 am
Forum: Beginner Basics
Topic: Accessing management interface on mikrotik SWITCH.
Replies: 6
Views: 3611

Accessing management interface on mikrotik SWITCH.

I have a Mikrtik Cloudcore switch I would like to access via winbox (or SSH, http) from a different subnet than the switch is on. All of the other managed switches I use have a management interface and you configure the IP/subnet/gateway for the management interface. As far as I can tell the mikroti...
by spammyduck
Wed Nov 26, 2014 6:04 pm
Forum: Beginner Basics
Topic: Can someone explain Mikrotik CloudRouterSwitches to me ?
Replies: 6
Views: 1585

Re: Can someone explain Mikrotik CloudRouterSwitches to me ?

When ports are in switch group, only IP addresses configured on master-port interface are accessible from those ports. And Torch can monitor traffic only processed by CPU, not by a switch-chip. There is no tool in a switch-chip except traffic mirroring. I don't want to assign IP's to ports I just w...
by spammyduck
Wed Nov 26, 2014 5:05 am
Forum: Beginner Basics
Topic: Can someone explain Mikrotik CloudRouterSwitches to me ?
Replies: 6
Views: 1585

Re: Can someone explain Mikrotik CloudRouterSwitches to me ?

If you want to use routing related features, you need to remove those specific ports from the Switch (Unset "Master port" value from this port). By default, ports are switched, and only some options are available for them. OK so you are saying that if I want to change the management IP and actually...
by spammyduck
Wed Nov 26, 2014 4:50 am
Forum: Beginner Basics
Topic: Can someone explain MIKROTIK_ADDRESS_LIST
Replies: 7
Views: 1681

Re: Can someone explain MIKROTIK_ADDRESS_LIST

the advantage to using an Address List instead is that the addresses in a list can be non-contiguous . So you don't have to waste an entire /24 (256 addresses) on a service offering that you might only have 50 customers signed up for. It also means that you can collapse all of those pools into a si...
by spammyduck
Tue Nov 25, 2014 3:05 am
Forum: Beginner Basics
Topic: Can someone explain Mikrotik CloudRouterSwitches to me ?
Replies: 6
Views: 1585

Can someone explain Mikrotik CloudRouterSwitches to me ?

Hello, I have 24 port Mikrtik CloudRouter Switch, not sure what to make of it. I have several Mikrotik routers and while I'm far from being an expert I know how to configure my IP addresses for the various ports, and my routes, and set up PPPoE server if needed or a VPN server. I can not figure this...
by spammyduck
Tue Nov 25, 2014 2:32 am
Forum: Beginner Basics
Topic: Can someone explain MIKROTIK_ADDRESS_LIST
Replies: 7
Views: 1681

Re: Can someone explain MIKROTIK_ADDRESS_LIST

You can use the Radius attribute Mikrotik address List to add the assigned IP, which the PPPoE user gets, into an address list on the PPPoE server.. So this is only good for assigning static IP addresses or can a radius server maintain/track an address pool from which to draw addresses from and sen...
by spammyduck
Mon Nov 24, 2014 4:23 pm
Forum: Beginner Basics
Topic: Can someone explain MIKROTIK_ADDRESS_LIST
Replies: 7
Views: 1681

Re: Can someone explain MIKROTIK_ADDRESS_LIST

So all it is is a tag sent via radius telling the miktrotik to use use a specific address list from /ip firewall address-list instead of the usual tag telling it what ip Pool to use ?
by spammyduck
Mon Nov 24, 2014 8:09 am
Forum: Beginner Basics
Topic: Can someone explain MIKROTIK_ADDRESS_LIST
Replies: 7
Views: 1681

Can someone explain MIKROTIK_ADDRESS_LIST

Hello all. I keep seeing this referenced in various posts I've found on the web while researching PPPoE / Mikrotik solutions. From what little I have found on the subject it does away with the need for IP Address Pools but I can't find enough information on exactly what it does, why I would want to ...
by spammyduck
Mon Aug 19, 2013 9:17 pm
Forum: General
Topic: DLL error connecting to one router via WinBox
Replies: 0
Views: 510

DLL error connecting to one router via WinBox

Hello We have several Mikrotik routers but are only seeing this issue with one router. For testing purposes we have a little 750G that we upgraded to the newest OS 6.2 (none of our other routers have been upgraded yet). Upon upgrading the router to 6.2 we get an error whenever we connect to it via W...
by spammyduck
Sat Apr 23, 2011 6:39 am
Forum: General
Topic: Do I have this Queue set up correctly
Replies: 4
Views: 673

Re: Do I have this Queue set up correctly

You have to set the pcq-classifier as well Create two PCQs, one for downloads with the pcq-classifier=dst-address and the second for uploads with the pcq-classifier=src-address. Set both rates to whatever you want each IP Address to have. Now use these PCQs in the queue-type tab of the simple queue...
by spammyduck
Sat Apr 23, 2011 6:22 am
Forum: General
Topic: Do I have this Queue set up correctly
Replies: 4
Views: 673

Re: Do I have this Queue set up correctly

Or if you can you can make a PPPoE Server and define in ppp-profile Rate-limit (example 2M/1M). This is much simpler since i beleive you have more than enough bandwidth (62*2M...) Clients than use and authenticate over PPPoE Clients I may end up doing that the problem for me is that it applies the ...
by spammyduck
Fri Apr 22, 2011 3:54 am
Forum: General
Topic: Do I have this Queue set up correctly
Replies: 4
Views: 673

Do I have this Queue set up correctly

I think I have the queue set up right but I'm not sure. I want a range of IP's rate limited 'per IP' . For example: 65.44.11.0/26 I want to create a queue that rate limits each of the 62 IP's in that range to 2Mbps each (each IP) down. I do not want the entire range limited to 2Mbps over all, I want...
by spammyduck
Sat Aug 14, 2010 9:28 am
Forum: Beginner Basics
Topic: How do I do the cisco equivalent of null route on 1 port ?
Replies: 4
Views: 1440

Re: How do I do the cisco equivalent of null route on 1 port

Ok well I guess technically that works for my 10.10. Ether5. How do I stop the other non-routables from going out ehter1 or coming in ether 1 regardless of where they came from ?

Thanks !
by spammyduck
Thu Aug 12, 2010 7:29 am
Forum: Beginner Basics
Topic: How do I do the cisco equivalent of null route on 1 port ?
Replies: 4
Views: 1440

How do I do the cisco equivalent of null route on 1 port ?

This is my first Mikrotik and it really makes me feel stupid. I can do all this stuff on a cisco but I can't even figure out why / when in / source is/isn't out/destination... when I expect I would be specifying the sorce/destination it wants direction (in / out) when I think I want to specify in or...
by spammyduck
Thu Aug 12, 2010 12:37 am
Forum: General
Topic: Limit number of failed pppoe logon attempts
Replies: 6
Views: 2148

Re: Limit number of failed pppoe logon attempts

Medianet I guess I'm just to dense to follow what you are telling me there. I don't see anywhere where I would tell mikrotik "use this pppoe profile if auth is successful" or "use this pppoe profile if auth fails".
by spammyduck
Wed Aug 11, 2010 6:16 am
Forum: General
Topic: Limit number of failed pppoe logon attempts
Replies: 6
Views: 2148

Re: Limit number of failed pppoe logon attempts

Medianet are you talking about doing that in your Radius profiles or did you do this somehow in the Mikrotik ? Can you point to more info on this ?

Thanks
by spammyduck
Tue Aug 10, 2010 7:55 am
Forum: General
Topic: pppoe problem
Replies: 1
Views: 465

Re: pppoe problem

I just posted pretty much the same question before I seen your post. I don't have the problem of other PPPoE users not being able to auth but our PPPoE auths via RADIUS so disabled accounts attempting to logon over and over and over makes our radius logs so large they are unusable. I want to do the ...
by spammyduck
Tue Aug 10, 2010 7:47 am
Forum: General
Topic: Limit number of failed pppoe logon attempts
Replies: 6
Views: 2148

Limit number of failed pppoe logon attempts

Hello I have googled and searched this forum but I have not found a solution to my problem. When one of our PPPoE user's account is disabled and that user has a router that doing the PPPoE auth for them their router continues to attempt to log on over and over and over and over hundreds or thousands...