MikroTik

wilburt

I am using an RB1100AHx2 router with hotspot setup. The user profile has no rate limit set, however I am only getting a max of 12Mbps download and 10 Mbps upload when I have a bandwidth of 100Mbps up and down. If i connect directly to a network that does not go through the hotspot I get the full ban...

wilburt

Hi, I currently use trial hotspot to give my users free access to the internet after they accept the ToS on the login.html page hosted on the Mikrotik. Instead of this process i am looking if this process is possible: 1. User connects to Wifi 2. Login page is directed to an external website for them...

wilburt

I am deploying the same setup to different site. The only items that would change would be the identity name of the device What is the best way to replicate all configuration settings from one Mikrotik device (I am using RB1100 for all my sites) to another site? (Quickly cut and paste configuration ...

wilburt

I am looking to configure on the eth ports of a RBcAPGi 3 vlans and 1 non-vlan this is the current setup PC -> RB1100 -> RBcAPGi -> RB411 all RB devices have the following bridges configured defaultbridge (no vlans) - this is used to bridge the eth ports together managementbridge (vlan8) to bridge v...

wilburt

Thanks All. The configurations listed above work as expected.

wilburt

Applied the following codes but network not able to get out. Does NAT rules need to be updated from out-interface to the specific IP address to NAT on?

wilburt

Can you put 2 IP ADRRESS on one Eth port?

I have two gateway end points but only one cable.

If yes, is it just simply adding IP address on the Eth port?

wilburt

Azam, is it necessary for firewall mangle rules to mark those packets? or the configuration you provide will suffice?

wilburt

Thanks Azma. Will try that and report back on success

wilburt

I have 3 Vlans setup on my RB1100 with one physical port as the connection to the outside world. How can I ensure specific VLANS go out a specific Gateway? Vlan10 192.168.10.x/24 Vlan20 192.168.20.x/24 Vlan30 192.168.30.x/24 Eth1 --> Gateways (172.16.1.1/32 & 172.16.2.1/32) outside world (WWW) W...

wilburt

see attached. Thanks

wilburt

RB1100 v6.37.2 Hi all, I have setup a simple hotspot setup using the hotspot setup wizard in the Router OS. However, when a connect to that hotspot network (wireless or wired) the default login page doesn't load. the static DNS entry is there referencing the hotspot gateway IP address HTML pages are...

wilburt

Do you still have to configure the base RB951 for other network and vlan setup first before enabling CAPSMAN? I have the following setup VLAN 8 VLAN 15 (hotspot wifi) VLAN 22 (private wifi) WLAN1 (physical) should be on vlan 22 WLAN2 (virtual AP) should be on vlan 15 is that possible to configure CA...

wilburt

I have an RB260GS and want it to operate like a L2 unmanaged switch. I have 3 vlans passing on my network Vlan8 192.168.88.0/24 (management) Vlan15 192.168.77.0/24 Vlan22 192.168.99.0/24 I have an RB951 configured with IP 192.168.88.107 However when i connect to my RB1100 to see if i can see the RB9...

wilburt

What is the best way to back up a configuration for RB1100 and then restoring to a new RB1100 that has a new version OS?

from 6.24 to 6.34.7

wilburt

I am looking to automate the data to be written to the RB log file.

I have come across https://wiki.mikrotik.com/wiki/Manual:I ... er_Profile

on-logout trigger.... will that be triggered when the client times out as well? and can that be scripted to write into the hotspot log file?

wilburt

2016-08-01 08:02:07 Local7.Debug 192.168.88.1 hotspot,account T-F0:Dx:E2:Cx:49:x6 (10.11.14.147): 351 134744 573870 925 803 (keepalive timeout)

What do the numbers at the end mean?
351
134744
573870
925
803

wilburt

Does the Hotspot logging in Mikrotik able to capture/print out for each user the total data transmitted for their session?

wilburt

Hi, i am trying to setup my RB411 as a wireless dongle for a PC that only has a lan port. I have tried settting up with the following cfg, but i can't get an IP from the router via RB411 # nov/26/2016 08:45:54 by RouterOS 6.37.1 /interface bridge add mtu=1500 name=vlan15bridge /interface wireless se...

wilburt

Does the latest Dude version 6 work on RB1100? I can't find a PPC version download.

If it doesn't work, then what options are there to use the latest Dude server?

wilburt

always the safest way.

Just wanted to see a solution comparable to the Rukus setup of wireless backbone.

Thanks

wilburt

This is for indoors (i.e. shopping mall). Looking to not have to install cabling to connect these APs back to the core router (internet gateway)

Looking to distributed APs throughout to provide wireless access out through a single point Broadband.

Thanks,

wilburt

Hi experts,

Can anyone recommend the best way and equipment to do AP to AP backbone without network cabling?

Thanks

wilburt

Thanks for the pointer. It works. There is one flaw. How do we ensure that a specific network can only go out 1 ISP and not the other? The good, 192.168.88.0/24 and 10.11.0.0/20 can't go out 172.16.1.0/24. However, Problem is 192.168.99.0/24 network can go out 10.10.10.0/24 ISP if 172.16.1.0/24 netw...

wilburt

So far so good. I am able to ping, and get DNS but for some reason i can't browse the internet.

THere are no firewall rules that are dropping packets.

I have static routes that point back and also NAT on that network and port.

any ideas where else could go wrong?

wilburt

Thanks heaps! i will read through

wilburt

Hi experts, I have two out interfaces to the WWW. What is the best way to push out bound traffic from a particular network out a specific gateway? For example Out Eth1 10.20.20.2 Out Eth2 172.15.12.2 Internal DHCP server 192.168.88.0/24 192.168.99.0/24 Looking to have 88 network out Eth1 and 99 netw...

wilburt

Thank you for the reply. I will try when I am home tonight. CHeers

wilburt

Hi,

Where can i get CM2 package for ROS 6.24? WIll the 6.33.1 CM2 package work on 6.24?

THanks,

wilburt

hi, I am looking to setup a vlan over my current network and wanted some guidance or suggestions on how best to do this. This is what i am looking to achieve on RB750 Core network 192.168.88.0/24 (used and admin to maintain and update network device Vlan2 network 10.0.0.0/24 (public network) Vlan3 n...

wilburt

Windows firewall is also disabled for both internal and external networks.

wilburt

Hi all, I have installed the Dude 3.6 on a Windows 10 machine. The discover doesn't pick up any of the devices. I have then manually added them into the Dude and can access the Mirkotik devices via login (admin password set) but the ping service states local problem. I have all UAC disabled and runn...

wilburt

Is there a configuration or system that works well with the MikroTik hotspot setup to help generate a report of what sites users visit on the hotspot system?

Thanks,

wilburt

I have seen a few Wifi hotspot systems that can provide some reports on where/which Wifi AP most users are connected to the Wifi system. Is there a way to do this in the MikroTik Hotspot system?

Thanks,

wilburt

Hi experts,

Is there anything required to be configured on the HOTSPOT server to ensure it uses the Web Proxy? I have setup the Web proxy using an internal micro SD card.

The Web Proxy cache content looks to have content from network connections not on the Hotspot.

Thanks

wilburt

Hi, I am trying to setup a hotspot system with RB1100AH and a RB951 as the AP. I have setup two vlans, 1 for the internal management and another for teh hotspot network. My management vlan 192.168.88.x is able to get onto the internet. However, with the Hotspot network (via 10.10.0.0/20) i am unable...

wilburt

Thank you for the reply. I have managed to get the two vlans setup on the master physical interface, but the other switch ports that reference the master don't seem to carry the Vlan information. I have tried to apply the vlan id per swtich port but the OS doesn't allow me to do that. Is it possible...

wilburt

hi experts,

I am new to the RB1100AH using OS6.1

I am looking to setup vlans on ether1-5 and have a dhcp server setup over these ports. I am not sure where to begin.

Thanks

wilburt

Hi Experts, I am experiencing with my hotspot setup clients that have poor network speeds when they connect. This is the setup Internet -- ADSL Modem -- (10.1.1.x) -- RB800 (setup with HS) -- (10.10.0.x) -- switch -- WAP | 192.168.88.x | Syslogd server I have setup a standard HS through the HS wizar...

wilburt

just in case anyone comes across this post, i did some test and for my case changing the wireless frequency helped wit hthe speed and stability of the wifi connection.

hope this helps anyone else.

wilburt

Hi MT experts, I have setup a Hotspot with the RB800 attahed to a vlan enabled switch which connects about 10 WAP (RB411s and RB433s). I have an IP range for the hotspot as follows 10.10.0.0/23 Some times when I connect to the wifi signal it takes more than 1 minute to get an IP address, some other ...

wilburt

Thanks fewi and Tim for your help.

It works.

wilburt

Hi, Here is the bridge port print out # INTERFACE BRIDGE PRIORITY PATH-COST HORIZON 0 I vlan8_e5 ManagementBridge 0x80 10 none 1 ether2-local-master ManagementBridge 0x80 10 none 2 I vlan15_e5 vlan15bridge 0x80 10 none Just to provide some clarification on what I have currently setup - I have setup ...

wilburt

Sorry copied the wrong HOTSPOT profile info. Everything is right except for the range. Here it is ip hotspot 0 name="hotspot1" interface=vlan15bridge address-pool=hs-dhcp-pool profile=hsprof2 idle-timeout=1m keepalive-timeout=none addresses-per-mac=1 ip-of-dns-name=192.168.5.1 proxy-status...

wilburt

ip hotspot 0 name="hotspot1" interface=vlan15bridge address-pool=hs-dhcp-pool profile=hsprof2 idle-timeout=1m keepalive-timeout=none addresses-per-mac=1 ip-of-dns-name=10.10.0.1 proxy-status="running" ip hotspot profile 0 * name="default" hotspot-address=0.0.0.0 dns-nam...

wilburt

strange... still nothing.

Does the MikroTik HS do something strange with firewalls filter rules?

wilburt

Hi,

I changed the rule to forward but still no luck. The only rule that gets packet counts are rules 5 and 8. It looks like it is skipping/not matching to my rule (1) at all.

Thanks.

wilburt

Hi, here is the print out. My rule is # 1 0 ;;; Make sure that proxy is not a open proxy chain=input action=drop protocol=tcp src-address=0.0.0.0/0 in-interface=ether1-gateway dst-port=8080 1 ;;; stop hs to untangle chain=input action=drop dst-address=10.1.1.9 in-interface=ether5-local-slave 2 ;;; D...

wilburt

Hi Experts, I have setup a simple hotspot system but I am unable to add specific firewall rules to restrict access to one specific host. Here is my network setup ADSL modem 10.1.1.x/16 ---> 10.1.1.9 Host (transparent web filter) (in bridge mode) --> 10.1.1.10 RB750 --> HS 192.168.5.x/24 I added the ...

wilburt

Hi MT Wireless experts!!! I have a simple WLAN setup with a RB800 as the primary router for the HS. From the RB800 I get 4+Mbps download speed, but at the wireless client I get a max of 80Kbps Is there something I can change on the wireless card to improve the wireless client download speeds? I only...

wilburt

Yeah... tried it and it doesn't work after authentication. Looks like a third party webproxy might be the only answer.

Thanks for your insight and knowledge!

wilburt

Thanks for the information. Is it possible to use the out of the box hotspot proxy to deny certain website after users have authenticated or for trial users?

wilburt

Hi MT experts, I am trying to setup a simple web proxy using the in built web proxy feature of the MikroTik. I have been able to setup it up using the information from http://wiki.mikrotik.com/wiki/How_to_Block_Websites_%26_Stop_Downloading_Using_Proxy and for the most part it succesfully blocks the...

wilburt

hi experts, I have a very strange issue. I have connected my RB800 to my Cisco877 adsl modem. When I ping from the Cisco... everything works fast. however, when I ping from the RB800 or any other device connected to the RB800 the first ping always request timed out, then the following pings come bac...

wilburt

Hi Experts,

Does anyone konw if it is possible to send to the log the web addresses that users visit from the hotspot service?

Thanks.

wilburt

Hi Blake,

Thanks for the pointer. I have finally got what I wanted to work.

Thanks again for your assistance

wilburt

It turns out that you can't see the vlan tag when you torch the vlan interface. You will have to torch an interface that is connected on the otherside of the vlan interface.

wilburt

I have setup a vlan on ether5 which is attached to another MT router on that port with the same vlan setup and id. The pings go through, but I can't see the vlan id. Should they be displayed? I can't see the vlan id in torch on the other side either.

wilburt

RB750 |___ Ether5 ___ Ether3 RB433(1) Ether2 ___ Ether3 RB433(2) |___ Ether1 ___ www | | |___ Ether2___ AdminPC | | | | Wlan wlan I have created a vlan20 to be used for the hotspot service on RB750 and attached it to ether5. Clients will connect to the wlan from teh RB433, but they won't know about ...

wilburt

In short this is what I have done On RB433 wlan - bridgevlan20 - vlan20 bridged together (vlan20, ether3, ether2) assigned an ip address to ether3 for management on the 192.168.88.0/24 network Ether3 is connected to RB750 ether5 On RB750 I have created Vlan20 bridged ether5 - bridgevlan20 - vlan20 H...

wilburt

I think that makes sense. I think that is what I have done (see below config) I am still unable to obtain an IP address from the hotspot server and also not able to ping between my 192.168.88.0/24 network for NTP and management purposes. I must be doing something wrong. This is what I have done for ...

wilburt

Thanks blake for the help I will give it a go and let you know of the outcome. Your last quote This config assumes your hosts can tag their packets with the proper VLAN ID. How does that work if the host doesn't know what IP address or vlan they need to be in? Can we set by default a specific vlan? ...

wilburt

I am trying to add a DHCP server to a vlan but none of my client machines are getting an ip address. are we suppose to add the dhcp server onto a physical interface or the vlan interface or a bridge?How/what is the dhcp server ip address? This is basically what i am trying to do Ether1 (master port ...

wilburt

Ok. That makes sense. If I already have IP traffic on that interface that I have just created a new vlan on, do I have to have all traffic from the different subnet within their own vlan? For example I have a HS on 192.168.5.1/24 on ether5 and then I created a vlan20 on ether5 with the vlan having i...

wilburt

Has it got anything to do with that physical interface being a slave? When i removed it from being a slave i was able to ping between the two vlans.

Sorry for all the newbie questions.

Thanks

wilburt

I have changed the VLAN interface to 192.168.90.x/24

but still i am unable to ping either way.

wilburt

Here are the export details [admin@MikroTik] > /ip address print detail Flags: X - disabled, I - invalid, D - dynamic 0 ;;; default configuration address=192.168.88.1/24 network=192.168.88.0 broadcast=192.168.88.255 interface=ether2-local-master actual-interface=ether2-local-master 1 address=192.168...

wilburt

There are no firewall rules on the 192.168.88.0/24 network.

Ether 4 is on the RB750 device and Ether 1 is on the RB433 device. The following IP addresses are set on the interfaces

RB750

Ether2 - 192.168.88.1/24
Vlan20(ether4) - 192.168.88.20/24

RB433
Vlan20(ether1) - 192.168.88.21/24

wilburt

I am trying to setup a basic VLAN without any success. I am following the basic setup as per the wiki manual SO what i have is two RB devices 750 and 433 I setup RB750 with the following /interface vlan add name=vlan20 vlan-id=20 interface=ether4 disabled=no /ip address add address=192.168.88.20/24 ...

wilburt

ok... so what I am going to do is setup two vlans for HS and for admin which there will be an internal IP address assigned. This is what I have configured, but I am still unable to get the communication between vlan10 between 192.168.88.11 to any other in that same subnet. RB750 E5 Vlan10,20 vlan 10...

wilburt

Hi Experts, I have setup a Hotspot on my rb750 on interface 5. I have configured a rb411 with wireless with a bridge of the wlan and the interface to be able to pass on network packets. I have setup ntp client on the rb750 and is able to obtain the correct date time. How do i setup the rb411 to sync...

wilburt

It turns out i need to check the read policy in my schedule (something i didn't originally do)

Thanks for the replies an assistance.

For future newbies setting up a schedule... make sure you enable the read policy

wilburt

Thanks for the pointer. I have created a script and a schedule, but it doesn't look like the schedule is working? It runs as the counter increments but nothing happens on the script side (the counter doesn't increment) Here is my schedule and scripts 0 name="hs-dhcp-enable" owner="adm...

wilburt

Thanks for the reply. I have tried to setup a filter rule with hs-input with protocol udp and action = drop but my devices on the hotspot are still getting thier ip addresses via dhcp. What filter setting would i need to set to prevent clients receiveing an ip address from the dhcp server on the hot...

wilburt

Hi, I am trying to restrict the times which people can access my hotspot. I was looking a dropping DHCP client request packets on certain times of the day. For example drop dhcp requests after 9pm I have seen the option available in the firewall section but can't get it to work. What is the time for...

wilburt

Hi Experts, I have been able to successfully setup a hotspot on the RB750 on one of the interface. I have also been testing that interface using a simple AP device and everything has been working to plan. For testing purposes it works, now I have gone out and obtained a RB433 with the R52 Wireless c...

wilburt

Thanks for the response. I have added the DNS name in the hotspot and that works perfectly. I have also noticed that we can't use proper domain names as certain devices try and resovle via it's own DNS cache and for some reason bypass the hotspot dns. Anyway my work around is to not have a .com or k...

wilburt

Thanks for the reply. It turns out to be a default feature of (specifically) iOS3.x and above, known as CNS. If i turn this off, then everything is fine.

wilburt

It turns out that it is due to the Auto-login feature of the iPhone OS3.x and above. Otherwise know as CNS. "With OS3.0, Apple introduced a new auto-login feature for wireless networks. When you join a network, the OS tries to to fetch a test page (specifically, this one). If it gets something ...

wilburt

Hi roadracer96,

Did you manage to get any solution with the problem you were having with the redirect to a specific page after login via iPhone?

Thanks.

wilburt

Hi, Yes I have also confirmed this with my iOS4 iPhone. It only works if i remove the dns name. It looks like it uses apple.com as the default dns server and tries to look it up. Has anyone found a way around it? I also noticed that when you select the specific hotspot you want to connect to, the wi...

wilburt

Thanks everyone for the replies. I have managed to get it to work now. It was a unclosed " that caused the javascript not to run. Everything is working as expected. However, I do have one additional question on the mobile login. I have tested connecting to the WiFi via the iPhone and at the mom...

wilburt

Thanks for the information. However, I did try running some basic javascript just on the login form and nothing happened. The script that I was running was a simple pop dialog box alert("hello"); and the script never ran. Is there a restriction on the javascript within the login page? Thanks

wilburt

Hi,

I have setup a hotspot, but everytime i connect to the hotpspot it shows in the url the ip address of the router (i.e http://192.168.0.1/login?...)

is it possible to make it (http://some name/login?...)

Thanks.

wilburt

Hi, I am trying to see if it is possible to use some javascript to detect the user's device and redirect them to the appropriate login page? For example. A user connects to the hotspot then the login.html will detect the device (using javascript?) and if it matches to a mobile device it redirects th...

wilburt

Hi MT experts, I have just got my RB750 and have been playing around with it and searched the web for various tutorials and help videos. However, I am still at a lost as to how to setup a vlan with a hotspot. So here is what i am looking to achieve (I think it should be possible on the RB750) - two ...

Search found 86 matches