Hi, I have hAP ac3 on 7.10rc1 I couldn't get both methods to work. pull method. importing remote image: adguard/adguardhome, tag: latest not ok registry auth response: 401 was unable to import, container 60913b7a-d045-477f-b917-85506f5d6dbf image method. importing tar archived image: adguard.tar err...

Hi,

Did you find any solution?

I had situation with 6.38 on my CRS I have CRS-1009 router and CRS-125-24G switch. Both of them was ROS 6.37. I upgraded both to 6.38. I am using Port based VLAN tagging described in http://wiki.mikrotik.com/wiki/Manual:Interface/VLAN / example #1 on my CRS-125-24 After 6.38 and all IP traffic stopp...

I thought it is only my phone's problem. Because non of other user I have seen have this problem around. Build in browser works fine.

Hi, For information. I had an issues with this version with RB2011UiAS-2HnD-IN It was running for 5 days with no problem but this morning there was no internet connection. I have bridge connection with VDSL modem. Winbox can see the router but can not connect with IP or macid. After lots of try with...

Hi,

I took it back to local distributor (Merpa Bilgil Islem http://www.merpazar.com/)

They were very helpful. They did some tests, changed antennas but no way. Probably bad wireless card issue.

Device changed.

New device works ok?

Yes.
-28db in the same room as seen on the above screenshot.

Hi,

I took it back to local distributor (Merpa Bilgil Islem http://www.merpazar.com/)

They were very helpful. They did some tests, changed antennas but no way. Probably bad wireless card issue.

Device changed.

Hi,

I took it back to local distributor (Merpa Bilgil Islem http://www.merpazar.com/)

They were very helpful. They did some tests, changed antennas but no way. Probably bad wireless card issue.

Device changed.

I was first opened the subject on http://forum.mikrotik.com/viewtopic.php?f=3&t=84731&p=424838#p424838 What I have tried for now is; Setting the region United States. But either with regulatory-domain or other settings, nothing worked . I opened the device. Nothing seemed wrong. Antenna conn...

Could you set frequency mode to "regulatory-domain" and Country to your country. And on the HT tab, select all chains as TX and RX and on the TX Power tab to default and see what your signal is? Did you upgrade your routerboard firmware while upgrading to RouterOS 6.12? If that doesn't wo...

Please try to reset the wireless configuration by clicking on the reset configuration for your wireless interface and configure it again. Also the power settings are the highest with country set to US. The calibrated settings are optimal and at their max when the country is set to US. Changing the ...

Well no noticeable difference. I played with all values between 5-25, constantly testing the performance. I got it down to -75db. Hi, I have the same problem i think. Signal is very week. I have RB2011UiAS-2HnD-IN. Can not get any signal from next room. Did you find any solution? This is my insside...

Is any device connected and goes thru any traffic?

Yes connected. Even no connection same result. I think it is a hardware issue.

I can not see my mikrotik signal from next room.

Hi, I have searched the forum but I couldn't find solution. Today I bought rb2011UiAS-2HnD today for a small hot spot project. But even build in basic configuration (WISP AP mode) I can not get enough wireless signal. Router is near my laptop (on the desk) and i can only get -68db signal. Not only m...

Hi,

I have the same problem. I have RB450G with ROS 5.6 and pings are too slow. (200-260ms) Not only pings, I have 20 Mbits download and when proxy is active speed test results only shows 5 mbits. With ROS 4.** I had no problem.