Community discussions

Search found 48 matches

by kbuska
Tue Jul 17, 2018 5:48 pm
Forum: General
Topic: RouterOS Virtual Labs
Replies: 84
Views: 113571

Re: RouterOS Virtual Labs

I'm trying to get CHR working on EVE-NG and it works but the interfaces dont seem to line up. I will put 192.168.1.1/24 on R1:ether1 and 192.168.1.2/24 on R2:ether1. I will make a connection from R1:ether1 and R2:ether1. I will then try to ping 192.168.1.2 from R1 with no success. I will move the IP...
by kbuska
Wed Mar 01, 2017 11:09 pm
Forum: General
Topic: 2017 USA MUM ??
Replies: 4
Views: 1102

Re: 2017 USA MUM ??

I'm interested in knowing this as well.
by kbuska
Tue Dec 06, 2016 10:31 am
Forum: General
Topic: CRS VLAN Dynamic Question
Replies: 1
Views: 418

Re: CRS VLAN Dynamic Question

bump. any thoughts? Do you need a diagram? Am I not making any sense?

Thanks.
by kbuska
Mon Dec 05, 2016 5:40 am
Forum: General
Topic: CRS VLAN Dynamic Question
Replies: 1
Views: 418

CRS VLAN Dynamic Question

I'm running into a problem where my CRS switch is funneling my traffic in ether1, ether2, and ether5 into VLAN 4095 dynamically and not the VLAN I setup (VLAN 1044). I have ether1 and ether2 a slave of ether5 and ether1,2,and 5 are all tagged and members of vlan 1044. For some reason though ether1,2...
by kbuska
Fri Aug 05, 2016 7:56 am
Forum: General
Topic: VPN (for TV streaming): not working on the router, working on the device
Replies: 4
Views: 933

Re: VPN (for TV streaming): not working on the router, working on the device

did you ever find a resolution to this problem?
by kbuska
Mon May 09, 2016 4:40 pm
Forum: Forwarding Protocols
Topic: redundant path advice needed - gns3 diagrams included
Replies: 3
Views: 779

Re: redundant path advice needed - gns3 diagrams included

any thoughts on this would be helpful or is disabling the lan port the best route?
by kbuska
Sat May 07, 2016 1:22 am
Forum: Forwarding Protocols
Topic: redundant path advice needed - gns3 diagrams included
Replies: 3
Views: 779

Re: redundant path advice needed - gns3 diagrams included

I created a netwatch to ping the IP address of the ISP. When down, it disables the LAN ports, when UP, it enables the LAN ports. The ISP itself is using vrrp so this is really for physical failure.
by kbuska
Fri May 06, 2016 10:52 pm
Forum: Forwarding Protocols
Topic: redundant path advice needed - gns3 diagrams included
Replies: 3
Views: 779

redundant path advice needed - gns3 diagrams included

I'm setting up a redundant solution and I'm looking the best path forward. I'm using vrrp and no routing protocols, just a default route to our ISP. I start a ping from 192.168.50.10 to X.Y.207.4 and its working great flowing in the below path. https://78ropq.bn1304.livefilestore.com/y3m6nVCybESD48R...
by kbuska
Mon Apr 18, 2016 11:31 pm
Forum: RouterBOARD hardware
Topic: CRS112-8G-4S-IN turns on with all SFP lights on solid, is it dead?
Replies: 0
Views: 534

CRS112-8G-4S-IN turns on with all SFP lights on solid, is it dead?

Was in the process of configuring a CRS112 and it just froze. All the SFP lights on are, the USR light is solid too. I also get no output from a console session. I tried a pinhole reset with no luck.

Any other thoughts?

Thanks,
by kbuska
Tue Apr 12, 2016 7:15 pm
Forum: SwOS
Topic: Is a 260GS backup config file board specific?
Replies: 0
Views: 919

Is a 260GS backup config file board specific?

If for some reason the unit dies and I replace it, can I upload the old unit's config file to restore settings or is it like R.OS and Routerboard where a backup is specific to a particular piece of hardware.

Thank you,
Ken
by kbuska
Tue Mar 08, 2016 12:37 am
Forum: Virtualization
Topic: Cloud Hosted Router
Replies: 583
Views: 189617

Re:

http://wiki.mikrotik.com/wiki/Manual:CHR#60-day_trial I read this, and it leads me to believe the P1 and P10 is per interface and the P-Unlimited is just that, Unlimited. You pay $250 and Mikrotik doesn't care how many interfaces you have on your CHR and at what speed. I'm just trying to clear up m...
by kbuska
Mon Mar 07, 2016 9:57 pm
Forum: Virtualization
Topic: Cloud Hosted Router
Replies: 583
Views: 189617

Re: Cloud Hosted Router

So stupid question time, unlimited license is still per interface or its unlimited?
Bump.
by kbuska
Thu Mar 03, 2016 10:39 pm
Forum: Virtualization
Topic: Cloud Hosted Router
Replies: 583
Views: 189617

Re: Cloud Hosted Router

So stupid question time, unlimited license is still per interface or its unlimited?
by kbuska
Sat Feb 06, 2016 9:31 pm
Forum: RouterBOARD hardware
Topic: HAP AC
Replies: 540
Views: 135287

Re: HAP AC

Is the HAP AC (non lite) available in the US yet?
by kbuska
Sat Feb 06, 2016 4:14 am
Forum: General
Topic: Can you view learned MAC addresses passed through the switch chip?
Replies: 1
Views: 405

Re: Can you view learned MAC addresses passed through the switch chip?

I solved the question for anyone who sees this in the future.

GUI: on a CRS based device Switch >> FDBs >> Unicast FDBs and then you can filter from there if you need to.

CLI: /interface ethernet switch unicast-fdb print where vlan-id="<VLANID>"
by kbuska
Thu Jan 28, 2016 5:42 am
Forum: General
Topic: Can you view learned MAC addresses passed through the switch chip?
Replies: 1
Views: 405

Can you view learned MAC addresses passed through the switch chip?

Is it possible to view a list of mac addresses being learned on a port on a CRS112? As a service provider we often will verify that a customers service is up if the port is up and we are learning mac addresses from the port. Having said that we are configuring these CRS devices to switch traffic wit...
by kbuska
Sat Dec 26, 2015 6:32 am
Forum: RouterBOARD hardware
Topic: where are the Rackmount ears sold ?
Replies: 1
Views: 1037

Re: where are the Rackmount ears sold ?

I never could find any so I had some fabricated in our machine shop.
by kbuska
Mon Nov 30, 2015 9:17 pm
Forum: General
Topic: SXT HG5 ac - No ether link
Replies: 4
Views: 670

Re: SXT HG5 ac - No ether link

Can you please move this to the hardware forum?
by kbuska
Sat Nov 28, 2015 6:52 am
Forum: General
Topic: Routing between 2 networks - EOIP issues
Replies: 4
Views: 590

Re: Routing between 2 networks - EOIP issues

Can you post your MT3 and MT4 routing table?
by kbuska
Sat Nov 28, 2015 4:52 am
Forum: General
Topic: SXT HG5 ac - No ether link
Replies: 4
Views: 670

Re: SXT HG5 ac - No ether link

The ethernet port seems firm and I can't see any issues with the sauder. I will test with my ohms meter each of the pins. I'm guessing by opening the case, I've voided warranty.
by kbuska
Sat Nov 28, 2015 2:59 am
Forum: General
Topic: SXT HG5 ac - No ether link
Replies: 4
Views: 670

SXT HG5 ac - No ether link

Not sure if the unit is toast but it seems to boot as I get one initial beep followed by two beeps but ive tried a few different computers and never get a link light. I've tried the POE injector on another device and it works fine. Also none of the LED light up on the back as they did when i put up ...
by kbuska
Wed Oct 21, 2015 6:32 pm
Forum: RouterBOARD hardware
Topic: Mikrotik policy on the announcement and production of new products
Replies: 7
Views: 1215

Re: Mikrotik policy on the announcement and production of new products

I found a mention where Normis mentioned that CRS were suppose to come with ears.

http://forum.mikrotik.com/viewtopic.php ... 67#p457467

Thank you,
Ken
by kbuska
Wed Oct 21, 2015 6:15 pm
Forum: RouterBOARD hardware
Topic: Mikrotik policy on the announcement and production of new products
Replies: 7
Views: 1215

Re: Mikrotik policy on the announcement and production of new products

Is there a source where I can purchase the ears for either a rack mount or a wall mount solution?
by kbuska
Thu Oct 01, 2015 8:44 pm
Forum: RouterBOARD hardware
Topic: CRS112 DC Power Requirements
Replies: 0
Views: 458

CRS112 DC Power Requirements

The device says 12 to 48 volts. where we have 48V, the DC plant is actually running at 53V. Is the slight increase going to cause a problem for these devices?

Thanks,
Ken
by kbuska
Fri Aug 28, 2015 10:32 pm
Forum: General
Topic: IPSec VPN through RB2011 isn't passing traffic through tunnel
Replies: 9
Views: 2352

Re: IPSec VPN through RB2011 isn't passing traffic through tunnel

[quote="patrick7"]The mangle rule is to exclude ipsec from FastTrack. You need the NAT-rule BEFORE any SRCNAT rules, because otherwise it will change the source address and the packet will not match any ipsec policy anymore.[/quote

That is only if the NAT rule applies to that source address, yes?
by kbuska
Fri Aug 28, 2015 8:07 pm
Forum: General
Topic: IPSec VPN through RB2011 isn't passing traffic through tunnel
Replies: 9
Views: 2352

Re: IPSec VPN through RB2011 isn't passing traffic through tunnel

If you are using NAT, you have to add an "accept" rule in the NAT table. I also had problems with using IPsec + FastTrack on the same device. I exclude all IPsec related traffic vom FastTrack: /ip firewall mangle add action=mark-connection chain=forward comment="Mark IPsec connections" \ ipsec-poli...
by kbuska
Fri Aug 28, 2015 5:54 pm
Forum: General
Topic: IPSec VPN through RB2011 isn't passing traffic through tunnel
Replies: 9
Views: 2352

Re: IPSec VPN through RB2011 isn't passing traffic through tunnel

RouterOS forwards everything no matter if it is ipsec or any other kind of traffic unless you have firewall rules set to drop something. You can check MTUs, maybe ciscos are configured to use a lot larger packets than standard 1500bytes. Thank you for your reply. Our layer 2 switches are set to 152...
by kbuska
Fri Aug 28, 2015 5:18 pm
Forum: General
Topic: IPSec VPN through RB2011 isn't passing traffic through tunnel
Replies: 9
Views: 2352

Re: IPSec VPN through RB2011 isn't passing traffic through tunnel

Did you exclude it from NAT and FastTrack?
exclude? I didn't have "not" nat statements if that is what you mean.

Also I didn't have any FastTrack statements.
by kbuska
Fri Aug 28, 2015 5:13 pm
Forum: RouterBOARD hardware
Topic: RB2011 (eth) performance
Replies: 14
Views: 2506

Re: RB2011 (eth) performance

I thought I would throw in my thoughts on what I have experienced with the RB2011 router. We temporarily moved a network to a RB2011 to do some maintenance on a Cisco router that was having issues. I was pretty apprehensive about whether the RB2011 SoHo router would be up to the task of supporting I...
by kbuska
Fri Aug 28, 2015 5:00 pm
Forum: RouterBOARD hardware
Topic: CRS112-8G-4S-IN Mounting Brackets (ears)
Replies: 1
Views: 818

Re: CRS112-8G-4S-IN Mounting Brackets (ears)

It looks like the CRS112-8G-4S doesn't come with mounting ears. Can these be bought as an accessory?
bump. I'm still looking for mounting ears to support a std 19" cabinet. Any suggestions would be appreciated.
by kbuska
Fri Aug 28, 2015 4:56 pm
Forum: General
Topic: IPSec VPN through RB2011 isn't passing traffic through tunnel
Replies: 9
Views: 2352

Re: IPSec VPN through RB2011 isn't passing traffic through tunnel

A few clients have complained that when we moved one of our providers onto a RB2011 temporarily, there Cisco site to site vpn's couldn't pass traffic. They said the connection would establish but they couldn't pass any traffic through the tunnel. I don't have much details as to there setup other th...
by kbuska
Fri Aug 28, 2015 4:54 pm
Forum: General
Topic: IPSec VPN through RB2011 isn't passing traffic through tunnel
Replies: 9
Views: 2352

IPSec VPN through RB2011 isn't passing traffic through tunnel

A few clients have complained that when we moved one of our providers onto a RB2011 temporarily, there Cisco site to site vpn's couldn't pass traffic. They said the connection would establish but they couldn't pass any traffic through the tunnel. I don't have much details as to there setup other the...
by kbuska
Wed Jun 24, 2015 6:42 pm
Forum: RouterBOARD hardware
Topic: CRS112-8G-4S-IN Mounting Brackets (ears)
Replies: 1
Views: 818

CRS112-8G-4S-IN Mounting Brackets (ears)

It looks like the CRS112-8G-4S doesn't come with mounting ears. Can these be bought as an accessory?
by kbuska
Thu Jun 11, 2015 9:53 pm
Forum: RouterBOARD hardware
Topic: has CRS112-8G-4S-IN been released?
Replies: 3
Views: 1295

Re: has CRS112-8G-4S-IN been released?

It looks like the product was released but no one has any stock as of yet.
by kbuska
Tue Jun 09, 2015 8:30 pm
Forum: General
Topic: LLDP
Replies: 126
Views: 43514

Re: LLDP

We also need LLDP... Please implement.
by kbuska
Sat Jun 06, 2015 4:45 pm
Forum: Wireless Networking
Topic: RB2011 / Unable to connect to an AP using radius.
Replies: 9
Views: 1578

Re: RB2011 / Unable to connect to an AP using radius.

Thank you for letting me know.
by kbuska
Sat Jun 06, 2015 8:34 am
Forum: General
Topic: CRS port based vlan question
Replies: 5
Views: 873

Re: CRS port based vlan question

Thanks again. My intent is to manage this from a remote location via the sfp port (its optical uplink) trunk. We will manage and access the switch via tagged 100, serve customer X on port 1 (untagged vlan 200) and serve customer Y on port 2 (untagged vlan 300). Because we wont be managing this switc...
by kbuska
Sat Jun 06, 2015 7:57 am
Forum: General
Topic: CRS port based vlan question
Replies: 5
Views: 873

Re: CRS port based vlan question

Thank you for your reply. I have console access as well and I cannot connect to it via winbox in either IP or mac. Should I be following the intervlan example instead?
by kbuska
Sat Jun 06, 2015 3:20 am
Forum: General
Topic: CRS port based vlan question
Replies: 5
Views: 873

CRS port based vlan question

I have followed the CRS examples and was successful in setting up tagged vlan management of the switch or the port based vlan setup but not both. Once I enter the commands to make my access ports slave to my SFP uplink, I lose management access to the switch and my port based vlan traffic starts flo...
by kbuska
Fri May 22, 2015 6:59 pm
Forum: Wireless Networking
Topic: RB2011 / Unable to connect to an AP using radius.
Replies: 9
Views: 1578

RB2011 / Unable to connect to an AP using radius.

I'm trying to connect my RB2011 to a neighboring Access Point which uses radius authentication. It doesn't use the mac address as the username. It uses the following check attributes. Can you recommend to me how to set up a security profile that sends the below info? Username: User1 (string) Passwor...
by kbuska
Wed Apr 22, 2015 7:20 pm
Forum: RouterBOARD hardware
Topic: has CRS112-8G-4S-IN been released?
Replies: 3
Views: 1295

Re: has CRS112-8G-4S-IN been released?

bump
by kbuska
Fri Apr 17, 2015 8:51 pm
Forum: RouterBOARD hardware
Topic: has CRS112-8G-4S-IN been released?
Replies: 3
Views: 1295

has CRS112-8G-4S-IN been released?

I'm looking to find information on CRS112-8G-4S-IN.

is it available?
when will it be available in the US?
what is the msrp?

Thank you,
Ken
by kbuska
Tue Jun 28, 2011 1:18 am
Forum: General
Topic: Information on VLan Setup
Replies: 5
Views: 860

Re: Information on VLan Setup

Thank you for your reply. I took your steps and completed 1 and 2 but I wasn't sure what you meant or how to proceed with 3 and 4. Also why bridge the main network ports together? It is strange to have all your network traffic to go through Ether2-local-master regardless of what port you are connect...
by kbuska
Mon Jun 27, 2011 11:47 pm
Forum: General
Topic: Information on VLan Setup
Replies: 5
Views: 860

Information on VLan Setup

I'm looking for information how to setup two VLANs that do the following; 1. Vlan 1 functions on ether port 5 and can access the internet but can not access resources on VLAN 2 or the main network 2. Vlan 2 functions on ether port 4 and can access the internet but can not access resources on VLAN 1 ...
by kbuska
Mon Oct 18, 2010 10:08 pm
Forum: General
Topic: One External IP unable to connect
Replies: 1
Views: 430

Re: One External IP unable to connect

Any feedback on this would be great. I'm clearly a newbie.

Cheers,
Ken
by kbuska
Sat Oct 16, 2010 12:59 am
Forum: General
Topic: One External IP unable to connect
Replies: 1
Views: 430

One External IP unable to connect

Regardless of the NAT port or Services on the router, I have 1 external IP that can't connect. I've tried other machines with public ip's and they connect fine. This one machine/ip worked a few days ago but stopped working for some reason. IP > Firewall > Connections doesn't list the connection atte...