Community discussions

MikroTik App

Search found 61 matches

by vlad8
Wed Feb 26, 2014 7:19 pm
Forum: General
Topic: vpn same subnet
Replies: 10
Views: 2011

Re: vpn same subnet

no there are 500/600 hosts but another person configured that /16 (i agree it's a stupid configuration).
Now i can't ask to change the ip configuration of all the hosts, someone could kill me!
It's more simple to change the site2 subnet...
by vlad8
Mon Feb 24, 2014 9:56 am
Forum: General
Topic: vpn same subnet
Replies: 10
Views: 2011

Re: vpn same subnet

So i think there's no solution...
by vlad8
Fri Feb 21, 2014 9:54 am
Forum: General
Topic: vpn same subnet
Replies: 10
Views: 2011

Re: vpn same subnet

sorry i don't understand, so how can i solve this?
by vlad8
Thu Feb 20, 2014 7:31 pm
Forum: General
Topic: vpn same subnet
Replies: 10
Views: 2011

Re: vpn same subnet

But then i'll have 2 pc, one in site1 and one in site2 with the same ip address! (ex. 192.158.50.6)
Could this become a problem?
by vlad8
Thu Feb 20, 2014 7:25 pm
Forum: General
Topic: vpn same subnet
Replies: 10
Views: 2011

vpn same subnet

Hi, i have a problem, i have to create a tunnel to link 2 sites with the following LAN subnets: site1 - rb750 - 192.168.0.0/16 site2 - rb750 - 192.168.50.0/24 Normally i would create pptp interfaces and add static routes on both rbs but in this case one subnet is a subnet of the other! Can anyone he...
by vlad8
Fri Jun 07, 2013 11:09 am
Forum: General
Topic: mikrotik and vlan
Replies: 3
Views: 655

Re: mikrotik and vlan

The problem is that with only 1 cable from switch i have to tag vlan on phones, that is possible and on pcs, that is very difficult, only few nics support vlan id in driver option.
by vlad8
Thu Jun 06, 2013 4:57 pm
Forum: General
Topic: mikrotik and vlan
Replies: 3
Views: 655

mikrotik and vlan

Hi all, i have a network with RB2011,cisco poe switch, ip phone with dual ethernet interfaces and pcs connected to them. I have linked the switch to ether5 and created two VLAN interfaces with id 11 and 12 and different subnets. I need data on vlan11 and voip on vlan12. The problem is that from swit...
by vlad8
Fri Dec 28, 2012 1:04 pm
Forum: Forwarding Protocols
Topic: PPOe + OSPF IP Public
Replies: 1
Views: 1640

Re: PPOe + OSPF IP Public

with pppoe you can deliver /32 public ip addresses. In your ppp secret "remote address" put the ip, then in ospf network add the public /24. When pppoe connection become active, you will it in ospf interfaces.
Remember to do not masquerade public ips :D
by vlad8
Thu Sep 20, 2012 6:00 pm
Forum: General
Topic: nat 1:1
Replies: 2
Views: 795

nat 1:1

Hi, this is how is configured a RB750: ip address 4 ***.***.***.130/28 ***.***.***.128 ***.***.***.143 ether5_WAN 5 ***.***.***.131/28 ***.***.***.128 ***.***.***.143 ether5_WAN 6 ***.***.***.140/28 ***.***.***.128 ***.***.***.143 ether5_WAN 7 192.168.1.10/24 192.168.1.0 192.168.1.255 ether3_LAN ip ...
by vlad8
Fri Jun 29, 2012 5:56 pm
Forum: General
Topic: log torch output
Replies: 4
Views: 4228

Re: log torch output

that's good! now if it's possible i have to remove from logs some unnecessary fields, because i have to give this output to the customer
by vlad8
Fri Jun 29, 2012 4:55 pm
Forum: General
Topic: log torch output
Replies: 4
Views: 4228

Re: log torch output

thank you! I'll try!
by vlad8
Fri Jun 29, 2012 12:25 pm
Forum: General
Topic: log torch output
Replies: 4
Views: 4228

log torch output

Hi all! i need to log to text file or better to a syslog server all the connections done by all the pcs on the lan.
I tried to search in router os but i didn't find anything. Do i need a script? Does anyone of you done this before?
Thank you.
by vlad8
Thu May 10, 2012 4:29 pm
Forum: Forwarding Protocols
Topic: Routing Public IP behind our NAT
Replies: 2
Views: 3151

Re: Routing Public IP behind our NAT

We have a routed network based on ospf. Clients get connection with pppoe-client that terminates on each bts and are routed with ospf. if the customer wants a public wan ip we only set it up on the radius so the pppoe-client gets the public ip. if the customer wants a public class behind the routerb...
by vlad8
Thu Mar 08, 2012 6:57 pm
Forum: Forwarding Protocols
Topic: Route clients to a 5th & 6th DSL line using 2 RB750s?
Replies: 6
Views: 2109

Re: Route clients to a 5th & 6th DSL line using 2 RB750s?

looking at the pictures it seems you have adsl routers with pppoe clients that forward all traffic to the rb750 and between rb750 and routers you have a switch. If this is right you only need 2 port on rb: 1 for clients and 1 to the switch. I'll setup the routers on the same subnet (ex. 172.16.0.0/2...
by vlad8
Tue Mar 06, 2012 5:09 pm
Forum: Forwarding Protocols
Topic: Route clients to a 5th & 6th DSL line using 2 RB750s?
Replies: 6
Views: 2109

Re: Route clients to a 5th & 6th DSL line using 2 RB750s?

Buy a RB1100 or RB1200 so you have much interface.
I also think that rb750 couldn't run as reliable main router, pppoe concentrator and dsl load balancer
by vlad8
Thu Feb 23, 2012 9:57 am
Forum: Forwarding Protocols
Topic: Multiple VLANs over WDS wlan bridge
Replies: 9
Views: 9140

Re: Multiple VLANs over WDS wlan bridge

add a second radio with antenna and you get 2 different links and more bandwidth.
by vlad8
Tue Feb 07, 2012 10:17 am
Forum: Forwarding Protocols
Topic: two RB433AH - PPTP tunnel - connect two local networks
Replies: 1
Views: 1479

Re: two RB433AH - PPTP tunnel - connect two local networks

you have to add a static route on each RB.

On the pptp server add dst-address=192.168.7.0/24 gateway=10.0.0.2
On the pptp client add dst-address=192.168.1.0/24 gateway=10.0.0.1

It should run.

PS: do not masquerade traffic over tunnel
by vlad8
Fri Dec 16, 2011 6:54 pm
Forum: RouterBOARD hardware
Topic: Channel Bonding
Replies: 1
Views: 598

Re: Channel Bonding

i'm not sure...i'll use at least RB1100 to be sure
by vlad8
Fri Dec 16, 2011 5:25 pm
Forum: RouterBOARD hardware
Topic: Making RB450G weatherproof
Replies: 2
Views: 973

Re: Making RB450G weatherproof

450Gs get quite warm. So I would put it in a bigger box.

Sent from my GT-N7000 using Tapatalk
put it in a waterproof outdoor box and add 5 waterproof rj45 connectors
by vlad8
Fri Dec 16, 2011 5:14 pm
Forum: The User Manager
Topic: migration to newer version
Replies: 1
Views: 744

Re: migration to newer version

nobody has an answer?
by vlad8
Wed Dec 14, 2011 6:27 pm
Forum: The User Manager
Topic: migration to newer version
Replies: 1
Views: 744

migration to newer version

Hi, i want to migrate our usermanager to the latest version. I see in the newer one the "Profile" section, but in our version rate limit is described directly in the user record by rate-limit="". Will this make problem to migration? how can i solve it? please i don't want to entry 1500 user manually...
by vlad8
Wed Dec 07, 2011 6:35 pm
Forum: General
Topic: Giving out public IP addresses
Replies: 3
Views: 1049

Re: Giving out public IP addresses

i always suggest to route public ips trough ospf
by vlad8
Mon Dec 05, 2011 9:58 am
Forum: Forwarding Protocols
Topic: Failover for internal hosting servers
Replies: 8
Views: 2721

Re: Failover for internal hosting servers

put 2 RB750 before the 2 server and then setup VRRP
by vlad8
Fri Nov 25, 2011 6:01 pm
Forum: Forwarding Protocols
Topic: pppoe over eoip causes packet loss
Replies: 2
Views: 1182

Re: pppoe over eoip causes packet loss

why run pppoe over eoip??
by vlad8
Fri Nov 25, 2011 12:01 pm
Forum: Forwarding Protocols
Topic: Require Routing Help!!
Replies: 2
Views: 1020

Re: Require Routing Help!!

i suggest to use ospf
by vlad8
Fri Nov 25, 2011 11:58 am
Forum: Forwarding Protocols
Topic: Block access between two ip address
Replies: 4
Views: 1885

Re: Block access between two ip address

you can do it only by local firewall on the 2 pc
by vlad8
Fri Nov 04, 2011 3:45 pm
Forum: Wireless Networking
Topic: problem with hotspot and tp-link 743nd
Replies: 5
Views: 2269

Re: problem with hotspot and tp-link 743nd

this happen beacause your tplink is natting so the hotspot log the mac address and the wan ip of the router.
To solve the problem set the tplink as bridge instead of router
by vlad8
Wed Nov 02, 2011 10:32 am
Forum: Wireless Networking
Topic: rb192 dual 2,4bg radio repeater
Replies: 5
Views: 874

Re: rb192 dual 2,4bg radio repeater

thank you for the answer, i've already read that and it's the last solution (routing with nat).
I would know if there's a solution to setup a trasparent repeater with 2 radio without using wds. But i think the answer is NO.
I'll setup the router with dhcp-client/server and masquerade.
Thank you guys
by vlad8
Mon Oct 31, 2011 5:15 pm
Forum: Wireless Networking
Topic: rb192 dual 2,4bg radio repeater
Replies: 5
Views: 874

Re: rb192 dual 2,4bg radio repeater

nobody have an idea?
by vlad8
Fri Oct 28, 2011 5:36 pm
Forum: Wireless Networking
Topic: link more 50 km
Replies: 3
Views: 949

Re: link more 50 km

a 50km link would be a unreliable link.
I would find at least 1 hop
by vlad8
Thu Oct 27, 2011 11:28 am
Forum: Wireless Networking
Topic: MIMO 3x3
Replies: 38
Views: 23810

Re: MIMO 3x3

you'd better to change antennas!
by vlad8
Thu Oct 27, 2011 9:55 am
Forum: Wireless Networking
Topic: rb192 dual 2,4bg radio repeater
Replies: 5
Views: 874

Re: rb192 dual 2,4bg radio repeater

i have to look at, but wds protocols are different and it will probably not work with mikrotik; i setup 2 different radio to avoid wds solution.
Sure i know that the "routed" solution will work but my target is to setup a L2 trasparent repeater (no matter if ssid and frequency change).
by vlad8
Wed Oct 26, 2011 10:57 pm
Forum: Wireless Networking
Topic: rb192 dual 2,4bg radio repeater
Replies: 5
Views: 874

rb192 dual 2,4bg radio repeater

hi, i have to extend signal from a dsl wifi router.

i have 1 rb192 + 2 wistron cm9 radio, i tried to configure wlan1 as station and wlan2 as ap-bridge and bridged the 2 interfaces, but it doesn't work.

Someone have another idea?
by vlad8
Wed Oct 26, 2011 7:24 pm
Forum: RouterBOARD hardware
Topic: RB450G - HDD Problem
Replies: 8
Views: 1369

Re: RB450G - HDD Problem

look in System -> Stores, it must be empty.
by vlad8
Mon Oct 24, 2011 3:40 pm
Forum: RouterBOARD hardware
Topic: RB450G - HDD Problem
Replies: 8
Views: 1369

Re: RB450G - HDD Problem

are you running user-manager?
by vlad8
Mon Oct 24, 2011 3:28 pm
Forum: General
Topic: RB750GL Strange Problem
Replies: 24
Views: 2644

Re: RB750GL Strange Problem

you said you have 2 connection from 2 different isp, are they cable adsl?
by vlad8
Thu Oct 20, 2011 12:39 pm
Forum: Forwarding Protocols
Topic: My problem with Hacker I want a solution
Replies: 10
Views: 3862

Re: My problem with Hacker I want a solution

a solution is to enable pppoe-server on hotspot interface instead of dhcp-server.
So if he hasn't got a username and a password he can't connect to hotspot
by vlad8
Thu Jul 28, 2011 1:31 pm
Forum: The Dude
Topic: Dude and radius probing..
Replies: 9
Views: 5321

Re: Dude and radius probing..

i had the same problem and i solved it.
i added dude ip in the router list of usermanager, and then i added the user TEST with, now i've got to understand how to change the password
by vlad8
Wed Jun 29, 2011 5:10 pm
Forum: Beginner Basics
Topic: multiple subnets via ovpn
Replies: 2
Views: 687

Re: multiple subnets via ovpn

burn your cisco and run an rb1200
by vlad8
Wed Jun 29, 2011 5:08 pm
Forum: Beginner Basics
Topic: VLAN trunk over EoIP
Replies: 2
Views: 2054

Re: VLAN trunk over EoIP

Any particular reason you would want to crate Vlan through EOIP? Also, the easy way to get data going in on one port to come out on the other port is to bridge it. Maybe you could try and explain what you wish to do?
by vlad8
Mon Jun 27, 2011 4:28 pm
Forum: Wireless Networking
Topic: NV2 & PPPOE
Replies: 7
Views: 1764

Re: NV2 & PPPOE

are you using a radius server?
by vlad8
Tue Jun 14, 2011 1:00 pm
Forum: General
Topic: ppp and routing
Replies: 2
Views: 679

Re: ppp and routing

maybe RBs at each branch haven't route for the other. try to add static routes: on branch 1 add dst-address=branch2-lan-subnet gateway=head-rb-tunnel-address on branch 2 add dst-address=branch1-lan-subnet gateway=head-rb-tunnel-address on head rb add dst-address=branch1-lan-subnet gateway=branch1-rb...
by vlad8
Tue Jun 14, 2011 12:46 pm
Forum: General
Topic: H.323 video blackouts - RB450G v5.4
Replies: 5
Views: 1687

Re: H.323 video blackouts - RB450G v5.4

try to disable firewall rules and repeat the test
by vlad8
Tue Jun 14, 2011 11:33 am
Forum: RouterBOARD hardware
Topic: Need for wireless Speed, higher speed than R52nM
Replies: 7
Views: 1404

Re: Need for wireless Speed, higher speed than R52nM

i suggest licensed devices
by vlad8
Mon May 30, 2011 3:56 pm
Forum: Forwarding Protocols
Topic: Network Routing
Replies: 5
Views: 1692

Re: Network Routing

my answer is:
leave all the setting as they are in your picture and setup static routing.
If you are planning to extend your network set up ospf dynamic routing.
by vlad8
Wed May 18, 2011 7:09 pm
Forum: The User Manager
Topic: disable logging
Replies: 3
Views: 6149

Re: disable logging

it is so easy...lol...i didn't see!
sorry mikrotik and thak you so much petrn
by vlad8
Wed May 18, 2011 6:24 pm
Forum: General
Topic: Route internal subnet to locally assigned public subnet
Replies: 4
Views: 1248

Re: Route internal subnet to locally assigned public subnet

Vlad, More servers than IP's plus even if I had an IP per server I'd still NAT for the firewall.
if you have public ips on each server there's no reason why you'd masquerade them...
NAT and firewall filter don't need eachother to run
by vlad8
Wed May 18, 2011 6:08 pm
Forum: The User Manager
Topic: disable logging
Replies: 3
Views: 6149

disable logging

hi, we have a user manager on ros 4.17. The problem is that logs and sessions fill all the available disk space, the we can't do nothing like delete or add user and also logs!!! i think that mikrotik MUST fix this because i can't delete 20000 log records every day! I must have an option to disable l...
by vlad8
Wed May 18, 2011 12:04 pm
Forum: RouterBOARD hardware
Topic: Mikrotik STX Channel width problem
Replies: 4
Views: 3152

Re: Mikrotik STX Channel width problem

if you want to use 40mhz channel you have to use the A standard.
Instead if you use the N standard you have to enable extension channel in the HT tab of the wireless interface.
by vlad8
Fri May 13, 2011 10:56 am
Forum: The User Manager
Topic: find by ip
Replies: 1
Views: 732

Re: find by ip

nobody can help me?
by vlad8
Wed May 11, 2011 5:20 pm
Forum: The User Manager
Topic: find by ip
Replies: 1
Views: 732

find by ip

hi all, we have a user manager radius with 1000+ users. We are replanning public ip's and my question is:
Can i get a list (with a script or something) of users with a specific ip address class?

Thank You
by vlad8
Thu Apr 28, 2011 12:40 pm
Forum: Beginner Basics
Topic: Share same users data base between two hotspot
Replies: 4
Views: 906

Re: Share same users data base between two hotspot

you can if you enable usermanager package on one of the routers, and use it as radius server
by vlad8
Mon Apr 04, 2011 12:14 pm
Forum: The User Manager
Topic: batch remove static ip
Replies: 1
Views: 2191

batch remove static ip

Hi all, i have a problem. I have to test each user and remove the static ip only if it is in a specific network.
For example if static-ip=192.168.4.x then i want to remove it else if it is 192.168.3.x do not remove it.
Can this be done with a script? Can some one help me?
Thank you
by vlad8
Mon Mar 28, 2011 6:03 pm
Forum: Wireless Networking
Topic: Success with 802.11N/NV2
Replies: 1
Views: 1153

Re: Success with 802.11N/NV2

maybe the cpu use is near 100%? check it during BW
by vlad8
Fri Mar 18, 2011 7:29 pm
Forum: Scripting
Topic: Dynamic NAT - Can this be done?
Replies: 3
Views: 1002

Re: Dynamic NAT - Can this be done?

my solution is buy more public ips :)
by vlad8
Wed Mar 16, 2011 9:59 am
Forum: Forwarding Protocols
Topic: Mail Server behing mikrotik and SMTP port forwarding
Replies: 3
Views: 3754

Re: Mail Server behing mikrotik and SMTP port forwarding

202.125.125.139 seems a public ip.

with service like smtp, pop, http i will asign to each machine a single public ip instead of doing dst-nat. I suggest you tu buy a public /29
by vlad8
Mon Feb 28, 2011 2:54 pm
Forum: General
Topic: Route internal subnet to locally assigned public subnet
Replies: 4
Views: 1248

Re: Route internal subnet to locally assigned public subnet

you could assign public ips to internal servers instead of doing dst-nat
by vlad8
Wed Feb 23, 2011 12:59 pm
Forum: General
Topic: Double Nating and Static Routing
Replies: 7
Views: 1567

Re: Double Nating and Static Routing

On main router: /ip route add network=192.168.2.0/24 gateway=192.168.1.20 /ip route add network=192.168.3.0/24 gateway=192.168.1.22 /ip route add network=192.168.4.0/24 gateway=192.168.1.24 /ip route add network=192.168.5.0/24 gateway=192.168.1.26 and on each secondary router /ip route add gateway=...
by vlad8
Wed Feb 23, 2011 12:44 pm
Forum: General
Topic: WISP Network
Replies: 2
Views: 759

Re: WISP Network

you can add a radius in your network, or set up your front end rb1000 as radius to lease public ips pools
by vlad8
Wed Feb 16, 2011 6:37 pm
Forum: Forwarding Protocols
Topic: pppoe service on eth
Replies: 1
Views: 717

Re: pppoe service on eth

resolved! it was a radius bug/incompatibility...now with user-managaer it's all fine
by vlad8
Wed Feb 09, 2011 3:57 pm
Forum: Forwarding Protocols
Topic: pppoe service on eth
Replies: 1
Views: 717

pppoe service on eth

Hi all, i have a little problem, some of our consumer do pppoe from a router (linksys wrt120n) to the ethernet of a rb750. Without radius no problem, pppoe from linksys authenticate and consumer surfs the web, but if they authenticate to radius no traffic passes. Have someone got any idea? maybe a l...