MikroTik

promind

Setup OSPF between routers and assign routing filter with RIPE-NET/22 le 32 Each time client gets PPPoE IP ospf will forward the route to the main router and therefore your BGP or whatever protocol you are using will redistribute it. Here is sample config: Router 1: add area-id=0.0.0.1 name=area1 /r...

promind

What BGP AS numbers are you using? Can you post your config?

Hi
Thank you for this answer.
I have already switched to OSPF and is working great.
I realized that for this to be achieved with BGP I have to use VRF which is too complex design for such a simple task.

promind

Hello, I am trying to make something simple but seems to me more complex than I expected. OK here's the scenario: ISP vlan10 - 6500 routes vlan20 - default originate vlan30 - want to send these 6500 routes to another router vlan40 -default originate to another router So basicly ISP ==> 6500+1 ===> 6...

promind

Same problem with queue simple dynamic created rules and queue tree static rules(disabled by the way). After some time queues disappear( day/day and a half ). Traffic load is ~250Mbps peak. CPU load is 8-15%. OSPF performance is slower than on x86 hardware. Running version is 6.1rc1 on CCR-1036-4S. ...

promind

Hello MikroTik,
Is VLAN working on 6.0 when enabled on x86 Intel PCI-X interface?
It's not working since first 6.x betas were released.

promind

Hi, I'm using RB800+SR71-A I have upgraded to 6.0rc4 and constant kernel failures appear. Cannot change frequency cannot downgrade... Had to remove wireless card to downgrade but the other side(rb800+SR71-A) is upgraded and cannot be reached. Is there any safe frequency in which it will connect. I'...

promind

Hi, I'm using RB800+SR71-A I have upgraded to 6.0rc4 and constant kernel failures appear. Cannot change frequency cannot downgrade... Had to remove wireless card to downgrade but the other side(rb800+SR71-A) is upgraded and cannot be reached. Is there any safe frequency in which it will connect. I'm...

promind

Hi,
Can anyone point the Power Amplifier chip for repair.
I have a pair of these cards with damaged PA.
Thanks in advance.

promind

Because Broadcom modules require external firmware to function properly.

promind

isn't there any embedded browser that can do the job?

promind

Hi all, My provider has a web auth enabled and I must login every time I reboot the MT. Is there any chance MT to autologin? Here is HTML source of there login form: <div><h3>Активиране</h3><div id="ws"><form name="auth" method=post action="http://91.139.151.3/scr/login"...

promind

Good day..

Dear Buddy..
How can we check which of the component having the problem when i not able to power it up.

Hi
If you plug/PoE or Direct DC/ and there is no light up I think that the problem is here:(look at the picture)

promind

Hello,
Is this adapter supported in RouterOS?
http://www.intel.com/products/desktop/a ... erview.htm
Thank you

promind

The RB433AH was mentioned just for the "wireless card problem". If the wireless card was overheating then the RB433AH would have that problem. The only problem I get is from the RB800 which now is quite good ventilated and don't have that problem...but the temperatures here match significa...

promind

The 4 big nozzles you see are empty(covered with net against the bugs that can get in) and the fresh air is sucked through them. Ventilation inside the box is quite good and hot air is not cycling. I must put bigger vent inside and additional power source to make it work better(5V on 12V vent isn't ...

promind

An hour and a half later this happened... CPU is 62/63C Outside temp is ~40C(actually 50+ under the sunlight) Enclosures doesn't seem to fix the problem... What should I do? Replace the items with x86 and throw away ~$1200+ ? P.S. It's not the wireless card because with RB433AH which is not ventilat...

promind

Here are some pictures of the actual enclosure and the routerboard inside.

P.S: It's 13:00 and the sun is burning over 50C and the link is still working.
That's good news for me and my customers.

promind

Changed enclosures with much bigger and with good ventilation + additional fan.
I'll report success/failure tomorrow during day time

promind

Ok. Tomorrow I'll be changing cases and will put big 35x25x20 metal cases with 2x120mm 4500rpm vents. Current cases are: http://www.vesuviustreamline.com/product/large-aluminium-outdoor-case-mikrotik-alix-routerboards.html Current vents are: 2x http://www.dekada.com/catalog/fan-50x50x10-el-bearing-4...

promind

I can calculate this myself, don't you think? Why I don't have that problem with RB433AH,RB600,x86 and etc. which are also exposed to direct sunlight. Cases are solid aluminum and have enough space for ventilation(I've put myself 2 hi speed coolers but they don't do the work). I think I'll switch ba...

promind

Another MikroTik product and yet another MikroTik disappointment... I've bought 3 of these cr*ppy RB800 to establish 802.11N link with 4 UBNT SR-71A cards. All seemed to work fine when temperatures were ~15/20C but when raised to 30+ I see a lot of wireless errors which bother me. 1. "too many ...

promind

How about IGMP packets?

promind

Here is a screenshot...
It reaches here and nothing happens and just stays there forever...
On rb600 it worx fine.

promind

Same problem here... I have a dozen of RB1000's which work as PPPoE servers...CPU goes for about 20 secs on 100% and all users got "terminated".
Please find any solution because I'll have to stop working with you MikroTik guys...

promind

Yes I know that...I already have serial cable but I cannot boot the linux ...which interface is the CF slot? sda/sdb or sdc?
It reaches "Loading kernel" and my serial connection stops there...
I'm using RB1000 I think rb1000 and rb600 should use same kernel, right?

promind

Unfortunately there is no such option...nevermind I've made myself serial cable and it's ok...but it would be nice if MikroTik guys add cf boot option within RouterOS

promind

I saw on internet patch for RB600 series routerboard but it's for the MPC83xx cpu.
I believe RB1000 is MPC8547(e500c) CPU...is there any official or unofficial kernel patch for that sort of routerboards?
thanks

promind

(offtopic)
I have 2.9.24(l4) licensed version that is still working on a Pentium I 133Mhz beast

(ontopic)
If you can setup OSPF with your providers it will be a lot easier to do load balancing based on bandwidth constants.

promind

My config is extremely simple. I use WDS transparent bridge (RSTP) - MikroTik advised me to use EoIP or VPLS but none of them worked for me...I don't think the problem is in my setup... All services except ssh/winbox are stopped - there is NO firewall, NO connection tracking and I have disabled pack...

promind

Yes, 90+Mbps of TCP traffic(tested with real traffic not bw test). The link is 6/7km with complete LOS but there is a lot of interference because of other wireless devices around. My link is: 7km - p2p with RB411AH(r52n) -53 signal ~ 95Mbps real traffic 37km - p2p with RB411AH(SR71-15) -64 signal ~ ...

promind

I've upgraded to 4.0rc1 and have setup only 1x1 connection and I've achieved 130Mbps UDP and 96Mbps TCP.
The cpu blows when I configure 2x2 connection.
Since one of my links is pretty badly configured I'm using just one antenna for now.

promind

MPLS & EoIP behave even worse.

promind

Hello MikroTik, I've been experiencing some troubles with 7km link and 2x2 R52N on RB411AH. Link quality is 100/100 CCQ 270/270Mbps but after 40Mbps link disconnects and I see constant 100% cpu usage on 25/30Mbps. I've removed connection tracking, unneeded services ftp/ssh/www, there is no firewall....

promind

a pair of 120sm. Parabolics.

To uldis - EoIP shows very very low performance( from 90Mbps to 25/30Mbps ) - WDS seems to work better for now.

promind

35km success!!!
2x2 SR71A.
So now I have stable ~50km link with 90Mbps-SD traffic.
35km SR71A - 117/117 - real traffic is 87/88Mbps tcp with a pair of intel core2duo "junkboxes" x86 and 2x2 connection.
11.4km R52N - 270/270 - real traffic is 140Mbps tcp with a pair RB600A and 2x2 connection.

promind

promind!

GOOD QUESTION ID THINK WHAT BETA VERSION DID YOU USE TO GET THIS

AS MANY PEOPLE THNIK THERE ARE MANY BUGS IN THE NEW BETA VERSION

4.0b3(first) 4.0b4 now
Antenas are from VOM - Varna, Bulgaria 120sm.

promind

11.3km link 2x2 connection with r52n and rb600a. Here is config of AP: /interface wireless security-profiles set default authentication-types="" eap-methods=passthrough group-ciphers="" group-key-update=5m interim-update=0s management-protection=disabled \ management-protection-k...

promind

Hello MikroTik. I have a strange problem which I cannot determine... I see different traffic going between two of my routers(RB1000) Legend: r1-ether1 is my outgoing interface to my local provider(bgp session eBGP) r1-ether2 is my internal interface to another RB1000 via iBGP(vlan based 1502) r2-eth...

promind

Hello,
can you confirm that it is really not working on 5Ghz?
Thanks.

promind

Ok now i see hope in you, you see i don't have area ranges specified,i have just area backbone, and between my routers i have 5ghz wireless links each of wireless card has it's own bridge (let say interface is Ni-K and the bride for it is ni-k-br, to this bridge is attached only that one interface)...

promind

Hello Well, i really don't have any problems with ospf in 2.9.51 and 2.9.50, it really worked spectacular til yestarday (with previous version like 2.9.4x there were problems with ospf you talk about). I'll try later to post here a config, maybe i really have some shitty conf ;), but anyway when so...

promind

One thing came up to my mind, i always download all packages and install them onto routers, so even if i don't use say dude package it's nevertheless installed, maybe that's what i'm doing wrong, maybe some additional package causes the problem? Is that possible? Best Regards Michal I don't think t...

promind

Work as designed! first pool will give out all addresses (254,253,252,....4,3,2) Then when it run out of addressees it will check for all free addressees and the will make a next run only trough free addresses I think this is the right way to do it - it would be much more expensive to check your po...

promind

there is a really small number of defective boards. Please contact your reseller for RMA. We will shortly provide a test method how to identify the problematic devices.

Report day 7:

promind

i would certainly do that, as i always try to use the ros version on all routers, but i have 3 x86 machines in my network, and i'm too afraid to upgrade them to 3.6 as therewere many reports of crashes on them. And i have pretty hard access to those sites so i can't afford to accidently cut off ove...

promind

Hello, I've recently noticed that ip pools are not being cleared after disconnect and ips stay reserved/I don't know why?!?!?/. So...everytime a user connects next ip is being chosen/not the free one/.Basicly that leads to filling the pools and mikrotik is choosing it's own pools/everytime I have to...

promind

I'm really having problems with the use of the RB600 boards. All my RB600 boards restarts constantly. Someone has the solution for that problem? Temporary solution: Remove the built-in cooler over the processor(* YOU WILL LOSE YOUR WARRANTY *) and attach *radiator*(1) with some decent thermal paste...

promind

to be compliant with FCC it had to be locked down to 26dB Sorry for writing here but all I have to write is about crossroads so I'll use this topic: I recently baught rb crossroads and it came with 2.9.47...I upgraded it to 3.6 and it died... serial connection says jumping to kernel code and after ...

promind

I can confirm the performance decrease ... The max I see with 5G-Turbo ist 26 MBit TCP in one direction. The RB333 are coupled back to back with an 60db attentuation. Signal ist 60 db. Wireless bandwidth is nailed to 54 MBit (*2) I checked it with routing, wds and eoip. Always conntrack off. Traffi...

promind

Use separate antennas and different pol.
Use "mii type 1" link monitor and do not bond EoIP tunnels/ use wds instead or it will eat your cpu/.
You can use different boards but that will cost rather expensive.

promind

I just make bandwidth test, But was unable to achieve better than 50Mbit/sec Full Duplex with real traffic already passing... Something heppend with aligment of antennas I suppose... I will check it. yeah, it's real... that is smt. real. at 50km we have usually 55-60Mbps bandwidth test and 45Mbps r...

promind

I put 5ghz-turbo , but only 3 chanel 5210Mhz - same thing 1-30ms (P Troughtput 30mbps) ?! 5250Mhz - ping 1-3ms (P Troughtput 55mbps) 5290Mhz - not try ,can turbo-mode work on any extra-chanel ? switch to country that supports more turbo channels. try decreasing the tx-power to 12dBm / link -65/-65 ...

promind

promind

For those who say that RB133 can handle more than 20mbps.
The test was between PC ---->RB133---->Rb133 and not PC ---->RB133---->PC. I'm sure the speed will be higher.

dude... its UDP...

promind

try tests on the other side of the boards/connect 2 fast x86 machines and do tests from them/

promind

I just reported one of my RB600 came in with a DOA POE. The board worked with DC jack.. but this board was destined for the top of a tower. Now the hassle of RMA. *sigh* -Louis I hoped that this won't happen but it happened... today I witnessed 2 reboots of the routerboard 600. I've already sent su...

promind

This might not be the fastest ever possible but it is the fastest cheap and easy solution.. RB411 each side, 5ghz 20mhz channel, nstream on, framer policy=bestfit.. 33-35mbit tcp, 42-45mbit udp.. -Gerard side1 :P III Dell GX110 866Mhz 128SDRAM 1x XR5 decreased to 19dBm side2: P III Dell GX115 1Ghz ...

promind

Change of Authorization RADIUS disconnect and Change of Authorization (according to RFC3576) are supported as well. These attributes may be changed by a CoA request from the RADIUS server: * Mikrotik-Group * Mikrotik-Recv-Limit * Mikrotik-Xmit-Limit * Mikrotik-Rate-Limit * Ascend-Data-Rate (only if...

promind

My rb600 had 2d uptime, but today was 2 reboots....

Tested RB600 on ethernet ONLY with 2 bgp sessions 2xVLAN and simple firewall.
It seems to be stable for now.
I'll report issues if there are any.

promind

Interesting... What about just using a radius client, and sending a radius attribute to the MT? One line, one command, no need for all these scripts calling more scripts, calling more scripts ;) Sending attribute is just when user connects. When user is online/realtime/ you cannot touch his/her que...

promind

Here is how I do it: 1. Create table clients where nas info is stored: DROP TABLE IF EXISTS `clients`; CREATE TABLE `clients` ( `cid` int(2) NOT NULL auto_increment, `client` varchar(15) NOT NULL default '0.0.0.0', `secret` varchar(32) NOT NULL default '*', `shortname` varchar(32) NOT NULL default '...

promind

This might not be the fastest ever possible but it is the fastest cheap and easy solution.. RB411 each side, 5ghz 20mhz channel, nstream on, framer policy=bestfit.. 33-35mbit tcp, 42-45mbit udp.. -Gerard side1 :P III Dell GX110 866Mhz 128SDRAM 1x XR5 decreased to 19dBm side2: P III Dell GX115 1Ghz ...

promind

mt support, any news?
u confirmed the problem or not?

regards

Not yet,
I've already replaced the board with PII 333Mhz MMX /before 18:00 is rb600 after is P II 333Mhz /

promind

The stablest ROS version for me was 3.0, this one give me 1 day and a few hours uptime. Just for testing I invert the wlan mode now the unit that constantly reboots it is a station-wds, before that it was the ap-bridge. I will keep you informed guys! No success with this change, the unit keep reboo...

promind

You sugest that an G4 2x1000 MHz perform better than a dual core at ~2x2Ghz?(AMD, Intel)? I can buy G4 2x1000 MHz at 135 euro/piece. If you find G4 at that price buy 10 more for me :) Now on the subject: G4 is equipped with integrated Gigabit Ethernet. It has 4 PCI-X slots each at 133/100Mhz 64bit....

promind

OK, that´s the kind of info I´d like to hear. I am planning to use it as replacement of my Pentium based PC. This PC is running now for two years in a row (apart from an occasional reboot due power failures). But, as we all know, one day the hd will fail, probably while I am away... Also, I can´t e...

promind

Thank you,

Is there an estimated date or release number for this update?

Are you planning to do xml/sql export to the user manager database?
How about *sql support?

promind

Hello MikroTik support,
Here is what happens with rb600 and what happens with P2 266Mhz MMX

promind

Hi promind, I have to avoid using more equipement, due to redundancy of all components. If you see, there is no redundancy in RB600s. What is the problem if RB600 die?.. This is solved using LACP but I can't use here. Thanks for your reply, it is very clear. Martín. Edit: If my costumer thinks that...

promind

Nz_monkey, If I use only one RB333 on each side and this RB333 fails, my link fails too. I need to use 2 RB333 on each side for redundancy, also for better bandwidth. I think that my schema/diagram isn't a strange redundancy solution. I need to have all electronics duplicated. changeip I can confir...

promind

I've got 4 5213 cards and with wireless-legacy driver on MT 2.9.50 I see: interface-type=Atheros AR5213 chip-info="mac:0x5/0x9, phy:0x43, a5:0x36, a2:0x0, eeprom:0x4006" pci-info="01:00.0" supported-bands=2ghz-b,5ghz,5ghz-turbo,2ghz-g,2ghz-g-turbo But when I want to use new wire...

promind

did this problem only appear recently after some upgrade, or was it rebooting from the start? where did you run the Btest from/to? We can't repeat it. It appeared in v3.3 and now in v3.4. In v3.3 rebooted because of ar5213 card/watchdog timer reboot or kernel panic/ in v3.4 there is no particular r...

promind

normis, just try to run btest localy, i mean run server and client on same rb 300 or 600, on my rb this try is ended by reboot. On other rb i.e. 500 there was no problem with this kind of test regards normis, Please respond if this is hardware or software problem to know what should I do... if this...

promind

I have rb333 with CM9 too. I use only CM9 cards on base stations.
Why I must replace my own card to Mikrotik R52?

My rb333 has 7 days uptime after upgrade (3xCM9).

it's not said that you should upgrade to r52h...there are plenty of AR5413 a/b/g cards

promind

too bad that the v3 stops at RC version. you should update it

Let mikrotik do rsync access to their webserver so anyone can be a mirror

promind

your image is from RB333, this topic is ONLY ABOUT RB600 I was talking to patt [the cm9 guy] RB600 has the reboot problem as told with whatever card you use/the high load is the problem/ both boards have problem with AR5212/5213 cards. I used the PC-684HA with RB333 and it performed the same way as...

promind

Hello I have one high performance ap - rb600. My throughput: received-packets-per-second: 2477 receive-drops-per-second: 0 received-bits-per-second: 16.4Mbps sent-packets-per-second: 2404 transmit-drops-per-second: 0 sent-bits-per-second: 7.0Mbps Configuration: 4 x Winston CM9 5GHz nstreme 48V 0.7A...

promind

Hi I have number of RB600's that all do a strange thing If i change any item on the wireless adapters then router reboots. Ie change frequency change country even if i disable or enable wifi card RB600 reboots. On workbench with little or no through traffic the problem does not occur but if i push ...

promind

rb333 has problem with high-power Atheros 5004X chip based mini-pci cards. It has been tested and only by changing to 5006X chip based cards the problem is resolved. seen reasons: kernel panic , watchdog timer reboot, without proper shutdown. I don't have dmesg so I can't bring out the whole output....

promind

I have experienced some problems with rb333 and AR5004X/ar5213/
It works fine but when loaded rb333 reboots.
Is there any solution or any other like me?

promind

Hello MikroTik , I'm thinking of gathering all my 4 links to a certain location. Here is the scenario: Point A(base point) Point B(Relay point 1) Point C(Relay point 2) Point D(remote point) My links are as follows. from Point A to Point B to Point D from Point A to Point B to Point D from Point A t...

promind

An additional info: users have various rate limitations, so I cannot just set a static queueing. You cannot do that. I've done some patches with which you can do ppp zone shapings, but it's only implemented in linux kernel and ppp daemon. for example ppp receives attribute Rate-Limit-Zone1=512K/512...

promind

My boards are rev.1 so ..one of the "old ones" as the seller said. The "55mpbs" board i was mentioning are probably the first rb333 i got.. i'm not sure what revision are, but are surely one of the "old" ones I've got upto 25 bwtest and in real test not much than 33/34...

promind

Hi, just my two cents... one of our main links is running up to 60Mbps. Signal is not good enough to reach solid 54Mbs*2 negotiation, and is running rc6 Bandwith test on this link (tcp) reported speed is 42Mbps one way.. still when in production it runs from 55 to 60 Mbps (it's "cut" to 5...

promind

how is "supout.rif" a link-threatening experiment? it's just configuration output file To Alex: I'm really amazed how you managed to get 55Mbps... I switched off firewall disabled connection tracking and also disabled ftp/telnet the bridge isn't stp/rstp and of course used wds not EoIP an...

promind

because port OS to another system is not that easy and that includes a lot of testing. and that all is not outweighed by demand for that feature hence, there will be no port to apple produce ppc computers as even apple have abandoned them and there will not be any new hardware from that manufacture...

promind

promind, Mikrotik images is "set" for specific hardware/peripherals. It's not generic, it will not run on PPC Mac's. Just because for example CPU is completely different, than Mikrotiks CPU. you don't get my point... If they are able to switch from mips to powerquicc then why not be able ...

promind

there are a lot of different PPC processors and support for each hardware has to be added individually. PPC is not a name or brand - it's architecture type. you can learn more about this here: http://en.wikipedia.org/wiki/PowerPC http://en.wikipedia.org/wiki/PowerQUICC I hope it helps :) I do know ...

promind

ppc system ONLY runs on RouterBOARDS. The only non-routerboard files are x86

But it's still PPC processor right?
So why not cd-image?

promind

Why isn't there PPC cd image?
I have some old PowerMacs that I can use as Routers.

promind

a supout.rif that is made during the max traffic would be very welcome.

Sent email/ not when max traffic/
I'll resend you during max traffic.

promind

Maybe post some details about your config and testing methods? A supout.rif file to support would be even better Sorry to hear that you don't even know about that... Yesterday I've spoken with a friend of mine who also got a pair of 333's and he made the same mistake./upgraded to 3.0rc9/. Same prob...

promind

Hello MikroTik! I've just purchased 2 rb333 with built-in ROS 3.0rc6. Bandwidth test were not exactly satisfying but I can handle that/45Mbps single direction MAX/. Now the tricky part... I've upgrated ROS to v3.0 stable and what happened?!? 25Mbps MAX /single direction/. Isn't it supposed to gain h...

promind

No one from mikrotik knows why?

promind

Disable "default authentication" in the wireless settings and then just add those MAC addresses you want to connect to the access-list... Or create security profile unchecking everything and checking only RADIUS MAC Authentification, click on wlan interface and set security profile to you...

promind

Is there any plans to support CoA on PPPoE/PPTP?

I'm working on a php script right now which will change the rate-limit without using radius attr.
but I'm stuck on updating queue/only upload is being changed/

promind

Hi I would like to know how to setup mikrotik to use userman pppoe connection, we are currently using this, but we would like to assign each client a public ip address, is this possible. Our ideal situation is to have certain clients 5 or so that require Public IP addressing to use them, but the re...

promind

set <pppoe-$username> dst-address=0.0.0.0/0 interface
=<pppoe-$username> parent=none direction=both priority=8 queue=default-small/default
-small limit-at=2000000 max-limit=2000000 total-queue=default-small

it does work but sets only upload to 2M...I need to do both 2M.
Any solutions?

promind

What motherboard you use? I have had problems with MSI motherboard with VIA chipset when using RB44G - it was not even possible to login to Mikrotik 2.9.49 because Mikrotik freezed just after boot. I have solved it by installing Mikrotik and RB44G on other system (Dell Optiplex with Intel chipset)....

promind

Hello ,
How to kill expired ppp connection within mikrotik?
I've been doing it with rsh on linux but I don't know how to do it under Mikrotik...there is not kill pid under mikrotik..all I found is /ppp active remove #
it suits me but I don't know how to deretmine the number just the username.

promind

option is using static queues, enabled/disabled by script. or create mangle rules with 'time' parameter and mark packets with different marks for different rules

and how am I supposed to do that when I'm using dynamic ip address pools?

promind

You need to disconnect user, if you want to change Rate-Limit configuration settings.

this is not an option...

promind

OK then, I'll try it out tonight.

Thanks much for replying, you two.
You're the best!

try using chain forward instead of prerouting

promind

Hi all, I have clients which connect using PPPoE , I'm right now using Mikrotik-Rate-Limit attribute to shape clients...but I am experiencing an issue with my shaping order... from 08:00 to 00:00 shaping is one/1Mbps for ex/ from 00:00 to 03:00 shaping is 2Mbps for ex. and from 3:00 to 06:00 shaping...

promind

I have a valid licence which just porchosed, right from installing 2.9.48 + Routerboard 44g instead of my 4 regular NIC i see a lot of unexpected problem! i should say long time i am working MK and i install and configure alot of MK in lot of places but this problem is not regular, the router which...

promind

not very helpful...

promind

this is my quagga config under linux. I want to migrate it to mikrotik's routing. interface eth0.401 ip ospf authentication message-digest ip ospf message-digest-key 5 md5 my-md5-key ip ospf cost 10 ip ospf hello-interval 3 ip ospf dead-interval 10 ! router ospf ospf router-id 172.16.0.1 redistribut...

promind

Firstly, you didn't post the entire debug output of radiusd -X (Radius will show you the exact contents of the packet sent back to the MT after authentication). Secondly, don't bother with accounting stuff... You problem happens before accounting and therefore accounting is irralevent Thirdly, I ha...

promind

Fri Dec 7 16:08:44 2007 Service-Type = Framed-User Framed-Protocol = PPP NAS-Port = 14 NAS-Port-Type = Ethernet User-Name = "promind" Calling-Station-Id = "00:19:DB:D6:20:CE" Called-Station-Id = "elitsat" NAS-Port-Id = "ether1" Acct-Session-Id = "81000000...

promind

radius_xlat: '' rlm_nibs (nibs_fill_user): end for user `promind' ------------ rlm_nibs (nibs_add_attrs): begin for user `promind' ------------ rlm_nibs (nibs_add_attrs): add PW_PASSWORD rlm_nibs (nibs_add_attrs): add PW_SESSION_TIMEOUT rlm_nibs (nibs_add_attrs): add PW_PORT_LIMIT rlm_nibs (nibs_add...

promind

You have to ensure that local PPP database is not configured (not used). As firstly local PPP data (ppp secret) is checked and only then RADIUS server is consulted. using radius server as primary , local database is untouched. but I cannot figure if user is receiving the Mikrotik-Rate-Limit attribu...

promind

You have to enable RADIUS client for PPP,
http://www.mikrotik.com/testdocs/ros/2. ... radius.php
Then if you have correct RADIUS server configuration, router should set dynamic queue from received attribute.

I've done that, but still no luck

promind

Hi all,
I have my own version of freeradius plugin and added mikrotik-rate-limit attribute to it.
How to configure the PPPoE server under mikrotik to bring up dynamic queue?

promind

OSPF on a PPPoE network is pretty simple to set up. Primary principles employed will be: All the backbone IP's will be in one 'area' - the backbone area and network. Every PPPoE server IP range will be in their own area, subnet and network and also connected to the backbone area. The ideal way to a...

promind

Hello George The link not crooss over the sea or lagoon is just jungle. And sorry for the bad information of the wlan card, actually i'm using the wlan card RB52H (350mW) and is very rare because I have a link point to point with the same feacture over the sea (Playa del carmen to Cozumel Island) a...

promind

11 easy steps to configure transparent bridge. / I do it for about 30 seconds :) / http://wiki.mikrotik.com/wiki/Transparently_Bridge_two_Networks still needs some work: 1. first two images are identical 2. you have erased interface names (why???) in the later pictures, although they are visible in...

promind

11 easy steps to configure transparent bridge. / I do it for about 30 seconds

/
http://wiki.mikrotik.com/wiki/Transpare ... o_Networks

promind

I have a DELL Optiplex GX110 with int. 3com lan and XR5
the RouterOS is 3.0rc9.
The problem is that sometimes the wlan sends diassoc to the remote which is also 3.0rc9 with Zcom 5213. I have to disable and enable the card to assoc again.
What it could be?

promind

you need this: 1 antenna + dual polarized feedhorn. 3 boards per side first board simple wds bridge to the other side second board the same as the first thirb board uses 2 ethernet ports with bonding over them you can setup balance-rr for more bandwidth or in your case you need failover link or mode...

promind

Everything I don't need is disabled and the cards are about 6 inches apart with no antenna so there is some self-intereference, I'm just testing before I mount them. If I run the test from an MT connected to one of the 133's across the link I get 15/20 so I guess i was just overrunning the CPU on t...

promind

I've put together my first Nstreme-dual using a pair of 133 boards and 4 R52-350 cards. I'm running 5Ghz turbo 5210/5800 and I have -68TX/RX and it says 18MbRX 24TX but running a bandwidth test from one radio to the other I only get 3.5MbTX 4.1Mb RX TCP and this is a 12 hour average. I expected muc...

promind

Yes and these cards are not only stable but cheap. I have several tests under linux /using the new wireless stack which ralink seems to support in there new version of drivers/ and links seem to be stable. No disconnects for about 72 hours of uptime. The only limitation is that ralink don't share th...

promind

there is no plans to add support for those cards.

So it remains just on Atheros and Prism...

promind

As you can all see on ralink's page there are linux drivers for station support. It would be nice if MikroTik just adds the module into the kernel and we can setup stations with these cards. I have already tested b/g/draft 2.0 N cards on linux and it seems to work very well. And yes it even works in...

promind

Hi all I had setup bonding: mikrotik version: 2.9.43 l4 WISP first machine: 3.2Ghz P4 512DDR2 , internal LAN , 2x XR5 ap-bridge , static wds bonding1 - slaves wds-1 /wlan1/ , wds-2 /wlan2/ mode balancing rr second machine: 3.2Ghz P4 512DDR2 , internal LAN , 2x XR5 station-wds bonding - slaves wlan1 ...

promind

I use Apple G4 laptop and I am unable to use winbox...I've heard that mikrotik winbox is just a GUI to telnet commands? can it be done for Apple?

promind

the point is : i want to make 5G busy with WDS , and 2.4G busy with clients .. if the 5G confg will be : /interface wireless set wlan1 mode=ap-bridge band=5ghz frequency=5180 ssid=zone.elitsat.net wds-mode=dynamic wds-default-bridge=bridge1 enable-nstreme=yes enable-polling=yes framer-policy=best-f...

promind

thats right , WDS gives you the ROAMING feature as Mobile cells do .. my question is , I just want to seperate clients connection from the WDS connection , thats mean 5G for WDS and 2.4G for clients only , am I correct ? if we ignore the need for roaming feature .. its exactle like this drawing : h...

promind

ok , so nice .... you mean both bands used as Wds connection AT THE SAME TIME ...is this necessary or just for emergency cases , 5G connection lost .. and using the same Wcard for clients and WDS would it make it slower , i read that once , if its true , can I use only the 5G for backbone WDS ? ok ...

promind

I think I should attach a simple map of that what I'm trying to do

promind

promind in your setup , are you using 5G for the WDS link of the AP's and the 2.4G for clients connections ? 1- i want to know couse i want to do this with my setup , and i dont see difference between the 2 band setup , is it the band ( 5 or 2.4 ) which will decide ? i mean do the 2.4G Wcards in th...

promind

Now...here we are... finally we have succeded to make our backup links but I have some troubles...so I'm giving you this situation and I will hope someone to help me solve it :) 1 link: AP 1 wifi card 1 EoIP 1 bridge 1 Ethernet / wifi mode ap-bridge -> AP 2 wifi cards 2 EoIP 1 Bridge 1 Ethernet / wi...

promind

This is because he create the wds-mode=dynamic. That is only used if you create wds-mode=static. Like this: /interface wireless set wlan4 mode=ap-bridge band=2.4ghz-b/g frequency=2437 ssid=Main wds-mode=dynamic wds-default-bridge=bridge1 disabled=no or / interface wireless set wlan1 disabled=no mod...

promind

I have something like this: One AP with 4 wireless cards, 3 of them for the backbone in 5GHz and one for clients in 2.4GHz. This AP is connect to Internet. I want to config him like a repeater. Can someone show me a simple config? I already look at examples in wiki for mesh and repeaters but can't ...

promind

I'm buing anntenas from Peshtera, and feedhorns from Sofiq ;). And once upon a Time, I produce feedhorns for Plovdiv, but they were not really good models :). Btw I think 1,2m dishes are better than the 1,4m models :). 1.4m dish AP 1.2m dish Client AP/city area/ Client /some village area :) / bigge...

promind

actually, the RB112 is a good client, and the RB532 is a good AP. If you use 112 as an AP ... well you could use the same as client too.

listen to the man

if you are using mikrotik as an AP the best chois for client is also mikrotik

promind

nothing. i don't understand you question. i'm looking for good AP client to connent to my AP which is Mikrotik running on rb112 + 2xCM9 i want to add few PC behind one AP client unit. i know that another mikrotik unit would by the best solutions but i'm looking for a cheapper device. the ONLY APC 2...

promind

I'm buing anntenas from Peshtera, and feedhorns from Sofiq ;). And once upon a Time, I produce feedhorns for Plovdiv, but they were not really good models :). Btw I think 1,2m dishes are better than the 1,4m models :). 1.4m dish AP 1.2m dish Client AP/city area/ Client /some village area :) / bigge...

promind

what dishes did you use? what is the 5-6ghz converter? 1.4 meters parabolic dishes, 5-6Ghz converters are made here in Bulgaria by several firms with enough RF equipment. Its not that hard to make one really, once you find, good, high quality connectors for them. yeah I know :) We buy ours from Pes...

promind

Hi there, I need to make a 6km link being able to do around 50/50Mbit. I have LOS and 23DbI 5GHz panels (can do dual polarization) and 400mw SR5 cards. One site will be on the ground and therefore hardware will be easy to replace, however the other site will be 200 feet over ground and expensive to...

promind

Schema and heights of points: point1(800m)<===15km===>point2(2300m)<==93km==>point3(1300m)<==11km==>point4(1000m) Config: Point1: PC: P4 Celeron 2.4Ghz, 256MB RAM, MiniPCI CM9, CF 512MB MT 2.9.27 Antenna: 90cm parabolic dish, 5-6Ghz converter, 2m low loss coax feeder Band=5Ghz-turbo,mode=ap-bridge,...

promind

your machines are enough for the task not enough...I use mikrotik just for bridge...I had enabled connection tracking...that was the problem...connection tracking reduces my cpu usage with about 30% and when the first machine reboots next was "attacked" by the big traffic going to it...an...

promind

send this file to support, we will see what's wrong: http://wiki.mikrotik.com/wiki/Supout exported config...watched it all over twice and nothing wrong... and now the real reason is not license key...it's ok...too much traffic goes through the machines...about 20Mbit on P3 866Mhz, can someone tell ...

promind

I think you'll have to post your configs to see if it's something misconfigured... Very strange, otherwise... Best regards, Christian Meis I've figured out the problem...but I don't understand why mikrotik depends on system time? the battery of the bios has gone away and it always shows time of mac...

promind

it happened again!
16:30 first mikrotik reboots 30 seconds after the second one and so on and so on....

promind

you said you use MAC winbox. that's something completely different. see this page about ports RouterOS uses: http://www.mikrotik.com/docs/ros/2.9/ip/service if you done all that i recommended - it is not a hack attack. check for power problems. bring down one of the routers, attach it somewhere els...

promind

www done that..no effect connects via winbox without any problems disabled user admin added random generated user with 12 symbols added 64 symbol default password for the new user disabled services all except winbox...and when I do nmap I see that ports 1720 2000 3986 are open? why are they open? I...

promind

change winbox port in `ip services`, set up firewall in `input chain` to drop all connections except for your IP, change ssh port, read the manual about how to protect your router I've done that...no effect for ssh..just disabled it... I connect through mac address via winbox... and also I don't se...

promind

but it looks like it is. it is nearly impossible for a software/hardware error to occur at the same time on all routers. I'm pretty sure it's not power failure... 1st router 0km 2nd router 13km 3rd router 47km from 2nd 4th router 36km from 3rd 5th router 32km from 4th 6th router 7km from 5th All re...

promind

enable all logs and set them to `disk` and then see what caused a reboot. either a power problem, or something else.

all logs stored in disk...and nothing again...
log just says router was rebooted without proper shutdown
no other messages...
also it's not power failure I'm 100% sure

promind

yes I did...but didn't set any neighbour address
...but the fact is that when I disable watchdog machines begin blocking one after another.

promind

Hello fellows...
I've experienced a very whicked problem...
It happens once a week or twice...All my mikrotiks(about 5 on the chain) reboot one after another..and there is no visible reason?
Can someone tell me if he/she experienced the same problem and what is the solution?

Regards Promind

promind

1-5ms , 47km link Nstreme 1
AR5213 both

Search found 153 matches