i made it 27 db for each side and its working good with me now but im still waiting

Don't say you were not warned.

After putting in bridge side 28 db nd in stations WDS side 27 db

Solved ......


Thanks dude for helping me

Insure you stay within the power limitations of the XR5. If you are using "tx-power-mode=all-rates-fixed", then you must set the tx-power=13 (23db true), unless you limit the speed to 24Mbps or less. http://dl.ubnt.com/xr5_datasheet.pdf I recommend setting "tx-power-mode=default". It selects the co...

It is a good sign for your radios if they start transmitting without noise after a frequency change. That shuts off the transmitter for a few seconds during the change, and allows it to cool a bit. I hope for you that it does not pick up the noise again. If the noise starts again, then you should p...

Thanks i got it now its solve the problem a bit im still need to change channel every 3 or 4 hours How do you know? It hasn't been 3 hours since you changed that power setting. It may have taken that long for the radios to overheat. no im not sure till now im waiting and i will be happy if you gonn...

It is possible you have already damaged the radios. The Ubiquiti radios are notorious for a power setting offset. Something about MadWiFi. Take a look at the bottom of this page under "Conclusion". http://dl.ubnt.com/ubi_mtik_power.pdf I have found the power offsets mentioned are shown only in WinB...

When you changed the tx-power setting, did you set the tx-power-mode also? If you did not change the "tx-power-mode=all-rates-fixed", then it will normally continue to use the default card rates. That would have saved your radios, and the problem may lie elsewhere. I have burnt up my share of radio...

Then that is 2db more than the max rating on those radios. Maybe overheating on the transmitters?
http://www.titanwirelessonline.com/v/vs ... asheet.pdf

really im not sure i was trying to decrease the tx power many times but useless

i have link between two points, with these details ! 1- Distance 30 KM 2- 30 M tower ,32 DB dish, RB433, XR5,LMR 1M 3- First site configuration ( Bridge , 40M Nstream, TX power 30 ,using supper channels ) 4- 2nd side configuration ( Station WDS , 40M N stream , TX power 30 ) Does that mean the Tx p...

Hello buddies, i have link between two points, with these details ! 1 - Distance 30 KM 2- 30 M tower ,32 DB dish, RB433, XR5,LMR 1M 3- First site configuration ( Bridge , 40M Nstream,TX power 30,using supper channels ) 4- 2nd side configuration ( Station WDS , 40M N stream , TX power 30) ----------...

Can i ask u , which Mini Pci u used?? and how many Km between tow link? and i see u can change the channel i'm sure its will be better I am using Mini PCI - 350mwatts distance for the link = 5-7km Did that give u any idea? Try use Xr5 its better with this distance and im sure u will get CCQ 100%

If not good, what will i do to achieve a better signal strength to improve the link. This is the point to point connection using mikrotik rb411.Again, i want to know the effect of nstreme in point to point wireless link connection. What is the best way to enable nstreme in mikrotik. Can i ask u , w...

I have similar setup, but where do someone set the nstreme in the wireless. What does it do and what is the impact of it on link.

nstreme first. This will clean up some timing issues

How is your fresnel?

sorry cant understand what is the fresnel

okay thanks

Read and learn about spanning tree, and implement it in your network.

I try it but nothing happen:(

Hi, I have problem with p2p I'm using dish 32db in tow side and rb433 with Xr5, and I'm using super channel 5800 when the bandwidth reach to 5mb/sec the ping became to much high between tow points http://img508.imageshack.us/img508/5712/49643193.jpg note/ I'm using bridge mode with station wds I'm ...