MikroTik

telepro

Hello Suntorytime,
Did you receive a satisfactory response or workaround for this issue?
We see the same issue (file name, group, and file access rights) as you reported above.

telepro

Have had SMB read access from a windows system to a files on an 1100AHx4 ethernet interface working successfully for extended time with no problems. Access to the router was via router ether3. Just added VRRP to the 1100AHx4 on the ether3 interface. Now mapping a drive from windows to this interface...

telepro

Was a work-around found to get the virtual IP address to respond to a ping request?

telepro

On RB951G-2HnD running V6.47, unable to successfully load a metarouter image. Entered command response is as follows: [admin@FasSat V3.05.03.U016] > /metarouter import-image file-name=openwrt-mr-mips-rootfs.v1.22.01.20200413.tar.gz import failed: file in archive goes out of root directory: ./FasSat/...

telepro

On RB951G-2HnD running V7.0beta8, unable to successfully load a metarouter image. Entered command response is as follows: [admin@FasSat V3.05.03.U016] > /metarouter import-image file-name=openwrt-mr-mips-rootfs.v1.22.01.20200413.tar.gz import failed: file in archive goes out of root directory: ./Fas...

telepro

Has anyone successfully loaded a metarouter image with v6.46.2? We use a script to configure our 951G routers every time we upgrade from one ROS to a later version. This same script runs on all of the 951 UNITS. After upgrading to 6.64.2, the portion of the script that loads the metarouter image no ...

telepro

When updating ~30 systems, all with identical configurations running ROS 6.42.3 on 951G devices, and using an identical script to perform the update: ROS update was successful. Firmware update was successful. However, on only 2 of the 30 completed updates, after the required reboot following the fir...

telepro

Thank you very much. I don't believe I have seen this format described before. So do i understand correctly: /interface sstp-client monitor VPN-To-Host once creates and returns a text buffer Example: ;;; VPN Connection to LCD-RTR status: connected uptime: 39m52s encoding: AES256-CBC mtu: 1500 local-...

telepro

Is there a command line request that will return the uptime for an sstp-client (available on the winbox interface status page when the sstp VPN connection is operational). It shows the time that this particluar SSTP vpn connections has been operational. Neither of these work: :put [/interface sstp-c...

telepro

Fix_Space.npk script did not work successfully on a RB750r2 after executing the following procedure: Device operational running ROS 6.42.5 Placed update procedure on flash partition using winbox Use winbox to execute reboot to run the Fix_Space.npk script. Device did reboot but not come up successfu...

telepro

Regarding your specific questions: 1. Our current requirements are for low speed and low throughput - maybe 1 GB per month on average for all devices 2. We use Verizon LTE in US, so Bands 2, 4, and 13 3. Moving forward, we have no need for legacy 2G, some (minimal) requirement for 3G 4. Region: Nort...

telepro

The flash size on the wAP is too small for our application. We have 900+ installations on 951G hardware. Future plans wilkl require us to support an LTE interface (US, Verizon, bands 2, 4, and 13). A wAP R 2nD -LTE would be a very satisfactory platform except for the limited flash size (16MB) since...

telepro

The flash size on the wAP is too small for our application. We have 900+ installations on 951G hardware. Future plans wilkl require us to support an LTE interface (US, Verizon, bands 2, 4, and 13). A wAP R 2nD -LTE would be a very satisfactory platform except for the limited flash size (16MB) since ...

telepro

+1 for SHA1 and SHA256 hash function
better debugging environment
indication of the line number instead of no response when attempting to start a script with an syntax error
output of line number when importing a script encounters a run-time failure

telepro

We run a Mikrotik 1100 ahx4 at a datacenter. It acts as a router/gateway for a number of systems that exist behind it at the data center. It also acts as a VPN server terminus point for a number of Mikrotik systems at geographically remote locations. The 1100 is currently running ROS 6.39.2 There ar...

telepro

Uldis, Sorry for any confusion. We do have the wAP R-2nD LTE card communicating over the Verizon network. We used the device as delivered (ROS 40.4) but saw earlier comments about needing to update ROS and the LTE firmware. Perhaps this was to result in better reliability. We were also told by our V...

telepro

Has anyone successfully connected the RouterBOARD wAP R-2nD with the Mikrotik included R11e0LTE-US cellular interface card to a Verizon LTE network here in the US? if so, wereLTE card or Mikrotik ROS updates required? SIM card was pulled from a working cellular interface from another operational dev...

telepro

thanks much for the reference

telepro

We have found that occasionally a downloaded .rsc script file to be used to update the configuration is corrupt when imported. The Testing indicates that the file is correctly received via FTP but is incorrectly retrieved from the local 'disk'. We can't determine whether it was incorrectly written o...

telepro

hello ,
In order to follow this discussion more carefully, could you make the image/diagram mentioned in your post of Feb 03,2016 at 7:06 pm available? i am unable to download it.
thanks in advance

telepro

Out situation: The Mikrotik device receives status data from local sensors connected to it via ethernet. This data needs to be reliably sent to a data center. The Mikrotik router has two available connections to the data center 1. a primary, ISP land based, hard wired connection, with no reasonable ...

telepro

Does anyone know: is there any way to control the rate at which pings are issued when Check-gateway features is turned on in a route definition? By default, it now looks to be about 1 ping every 10 seconds. i would like to slow this rate down.
thanks in advance.

telepro

+1 for this feature request. would be quite useful.

telepro

I concur. The provided programming and database has proved to be very useful; when employed, it filters out a significant amount of unwanted and problematic traffic. Thus our question regarding whether anyone else was seeing traffic from Microsoft corporate sites blocked. Thanks for the info.

telepro

We have been using the blacklist provided by IntrusDave with success. However, we have on infrequent occasions found the list contains an IP address that is the source of Microsoft download web sites and files linked to by their corporate web pages. Momentarily turning off the use of the blacklist p...

telepro

There are a number of additional columns (in addition to the defaults) that can be selected for display through winbox. For example, in the PPP | Interface screen, columns may be selected to display TxBytes, RxBytes, TxPackets, RxPackets, RemoteAddress, etc. The command /interface sstp-server print ...

telepro

FYI: have updated to both 6.12 and then to 6.13. Problem still exists on both ROS versions

telepro

Already reported to support as [Ticket#2014050766000641]. However no response from Mikrotik. Failing system is in production and updates need to be scheduled during off hours. Since the issue takes several days to demonstrate failure, scheduling an outage to upgrade to a new version that has no expe...

telepro

Memory utilization on MikroTik 1100AHx2 acting as the PPTP and SSTP server to ~ 170 MikroTik RB443 and 951G systems, each acting as a VPN client continues to climb. After reboot and all VPNs are connected, memory utilization is about 41MB. After couple of weeks memory utilization has risen to 290+ M...

telepro

Hi, I can see the same here for 3 sstp links, always a reconnect after 2 minutes saying "terminating... - conn timeout" in the logs of the client. A link from Windows to the router using sstp seems not to be reset after 2 minutes. SSTP driving me crazy... why is it so unreliable. We have ...

telepro

SSTP problems still persist: We have SSTP server-client interconnections between 6 MT routers, all of which share *exactly* the same settings. After upgrading them to v6.12, some pairs would connect without problems, others however would disconnect after roughly one minute, mostly returning a "...

telepro

yes, we did change that when upgrading from 6.5 to 6.10. But thanks for the thoughts, anyway.

telepro

6.11 did not fix the problem in our environment either.

telepro

Hello, Did you ever arrive at a solution? i see the same problem, as duplicated by the sequence of first dozen or so messages indicating VPN shutdown, when using SSTP to create a VPN. In my case, both the client and servers are Mikrotik 6.10 systems (951G client and 1100AhX2 server). Did you submit ...

telepro

i am experiencing the same problem with official 6.10. We have a Mikrotik 1100AhX2 running the SSTP server, and we have a number of Mikrotik 951G units that are acting as SSTP clients. The connection stays up for about 2 minutes, then client disconnects and a few seconds later reconnects. This conne...

telepro

Would like to see option to configure a single wireless interface in CPE configuration to act simultaneously as both an access point for one SSID and as a station on another SSID. Useful where wired uplink is not available (thus station connection), and wireless often not Mikrotik components.
Thanks.

telepro

The option to execute a script fails after the following reset-configuration command has been executed and the routerboard has restarted if the file x.rsc is greater than or equal to 64kB. Files .LE. about 63.5kB execute successfully. /system reset-configuration keep-users=yes no-defaults=yes skip-b...

telepro

The option to execute a script fails after the following reset-configuration command has been executed and the routerboard has restarted if the file x.rsc is greater than or equal to 64kb. Files .LE. about 63.5kb execute successfully. /system reset-configuration keep-users=yes no-defaults=yes skip-b...

telepro

i have not seen the error you reported when i log on using winbox using the admin account and start a terminal session to enter the commands. i suspect that the admin account may have the 'policy' ploicy. However, if i do try the reset command with a request to run an x.rsc file after reset /system ...

telepro

I have tried each combination of the additional parameters: no-defaults=yes and no-defaults=yes skip-backup=yes and skip-backup=no but without success. i have also tried with a very simple, one line .rsc script file: /system identity set name=xyz123 to see if i can get this very simple script to run...

telepro

Does this feature - running a .rsc file automatically after a /system reset-configuration work in the latest 6.xx revisions? i have placed a file in the files window (x.rsc) and executed the command: /system reset-configuration run-after-reset=x.rsc The configuration is executed, the router reboots,...

telepro

Does this feature - running a .rsc file automatically after a /system reset-configuration work in the latest 6.03 revisions? i have placed a file in the files window (x.rsc) and executed the command: /system reset-configuration run-after-reset=x.rsc The configuration is executed, the router reboots,...

telepro

There are a few issues, but they are not fixed in the above build, that's why they are not in the changelog. Which specific issue are you talking about? Regarding scripting errors, please see http://forum.mikrotik.com/viewtopic.php?f=1&t=73772 Although the additional output produced by running ...

telepro

Hi, We have 2 problems with the Ros6.1 release. importing rsc scripts has changed the calling structure and also the maximum characters per router script has been changed in Ros 6.1 The first problem is fixable with some work on rewriting the structure of the scripts, aka where we had to \\\ a &quo...

telepro

i believe this is a problem introduced in 6.1, and was not present in 6.0. See http://forum.mikrotik.com/viewtopic.php?f=1&t=73772 and http://forum.mikrotik.com/viewtopic.php?f=2&t=73583&start=74 for other reports regarding the same issue. so far i have not heard from Mikrotik whether th...

telepro

Thanks for the reply. i understand that files entered at the command line require braces surrounding the script. This problem was not a script entered from the command line. The script was created as a file and was composed on a windows system. We then started winbox, and used drag and drop to place...

telepro

Has script processing changed in 6.1 from 6.0 This script, called demo1.rsc, copied to the files directory, and executed with an import command: # This is a comment :local xyz "xx123"; # Three previously acceptable lines :log info ("----- Config admin password to $xyz") /user set...

telepro

Is it possible to configure a single wireless adapter act as both an Access Point (for one SSID) and a station attempting to connect to another Access point (with a different SSID)? I see that when configuring a wireless adapter you must choose AP or station, and there is no way to select both. Addi...

telepro

Thanks much for the info that it can be made to work. We'll give it a try. Since there are about 90+ standard attributes, do you remember in which attribute you sent the group name? The only standard Attribute with 'group' in its name that I find is "Tunnel-Private-Group-ID", which does no...

telepro

i have been successful (as I believe you have) in implementing PPTP VPN authentication using a FreeRadius. However, I have not been able to successfully use the response from FreeRadius to authenticate a WinBox login. For Winbox I needed to implement a Mikrotik User Manager, which was certainly not ...

telepro

Have tested v5.25rc1 on 3 RB951G units for ~ 40 hours each. Would have expected to see 6 or more failures on each during that interval. Have found none. Thanks much.

telepro

Thanks very much for a great utility. We use it continually during development of new router configurations. And it makes comparing previous and updated ROS configurations so much easier to read and manage. One question (or suggestion): is there an option to keep the format for script source intact ...

telepro

The following 5 router restarts produce different running configurations after the 751G-2HnD 751G-2HnD reboot was completed. There were no changes manually entered between the tests (reboots). All were done on the same 751G-2HnD. These erratic boot-up results can be duplicated on all of the routers ...

telepro

Thanks for the response. RE: 1) Every RouterBOARD is produced and shipped with NAND that is fully appropriate to run RouterOS on it (size might be different). Understand. I was not complaining that 64MB appeared on some 751G routerboards, while others had 128MB. I merely expected them to all be prod...

telepro

although there are several other isues regarding the 751U routerboard, i have little or no experience with them, so i have opened this issue specifically for the 751G. i have 20 7510G-2Hnd units purchased over the last 5 months or so. We are testing them as a possible replacement for new installatio...

telepro

Thanks much for the workaround. No problem in changing our procedural sequence to implement this as the units are staged. We write up and execute strict, detailed staging procedures with the hope of eliminating any differences in delivered units. And it had not occured to me to change a setting on t...

telepro

Mikrotik support: Thanks for the response. i have emailed the image to you. As mentioned above, we build each of these syystems with an imported script. Regarding your suggestion to eliminate the redundant scripted, followed by the manual metarouter definition sequence: I have tried unsuccessfully t...

telepro

The file is available at \\192.55.195.201\Mikrotik map this location as a drive and log on with: UID: MikroTik Pass: R0ut3rHe1p (0=zero, L in help=one) the 2.9MB image file can then be copied to a location of your choice. The ROS is initially built with a script that contains the following fragments...

telepro

I have 4 production systems based on 433AH which as of today have respectively 10, 11, 25, and 53 days of uninteupted operation. i know i have had one of these systems up for greater than 120 days before it was rebooted (for some other reason). This sytem has ROS 5.6 and a single additional metarout...

telepro

thanks much. your suggestions were exactly on target. i appreciate the help.

telepro

thanks for your suggestions. However, the problem still persists. Have so far tried this on seven (7) of a batch of ten 433AH units received from the factory. Have also verified this same operation on three new 751G units. have tried this as far back as 5.6 and up to and including 5.16. i do note th...

telepro

Any update on this issue?

telepro

thanks for your suggestion. i have tried that, but without success. Authentications seems to arrive, but only the access rights associates with those specified in the default_group specified is ever allowed. for example: i expect logging in as jpj/jpj1 should provide rights assocatec with Group 'ful...

telepro

telepro

Runing RouterOS 5.6 on RB433AH. I use WinBox to configure the metarouter to run using 24MB of memory and successfully import an OpenWRT image. Image runs fine and indicates it has allcoated 24MB. However, after reboot of the computer the metarouter indicates it is using only 16MB. OpenWRT image succ...

telepro

I am running Routeros 5.13 on 1100AHx2. Have successfully installed user-manager. Have successfully configured a number of RB433 RouterOS 5.6 systems to request user authentication from the 1100 when loging in the 433 using Winbox. The RB433 systems have the standard user groups 'full', 'read', and ...

telepro

Thanks much. I will give loading /export output a try. I had read just the opposite elsewhere (use backup and not /export output), but that must have been in error. Are the other items you are aware of in addition to MAC addresses that must be deleted?
thanks again.

telepro

i have several identically configured RB433AH routers, each with a single wireless R52HN wireless adapter. Using winbox i select the files menu and then execute a backup request. Using winbox i transfer that backup file to another RB433AH w/R52HN hardware (same configuraiton) i then use this backup ...

telepro

The installation of Dude (latest beta version and previous stable version) fails during reboot. The following messages appear in the log after startup on the routerboard 450G verified dude-4.0beta3-mipsbe.npk installation of dude-4.0beta3-mipsbe.npk failed. could not create dude/lib/libresolv.so.0: ...

Search found 69 matches