MikroTik

phuang3

I don't think so. "qcom" says it all.

phuang3

Thank you, all of you. I can see the TX power now! It will disappear if the wifi window was closed. And, there are 2 TX power columns! That's weird enough. Before hap ax3, all my devices were V6. It took me lot of time upgrading to V7, especially the wireless part. It had changed so much . Before V7...

phuang3

Just pick up a hap ax3. It took me a while to make it work on my home networking environment. However, I found the v7 WiFi not showing the TX power. On CAPsMAN, my older devices are fine. How can I get the TX power info from WiFi? Is there any reason hiding this information? https://kspqm.kymco.com/...

phuang3

Thanks for the reply. The CAPsMAN is currently on RB450GX4 which I mentioned as CAPsMAN host. You are right about the 16MB storage problem. The one with older versions are with 16MB storage. They can't do the upgrade from WinBox though. I will probably do you've suggested. Just use AX2 device alone ...

phuang3

Hello, Here is what I have for my home network. #1 WAN to ISP. CAPSMAN host. #2 switch only. #3 switch only. #4~#6 wireless APs managed by CAPSMAN https://kspqm.kymco.com/ckfinder/resource/johnny/image/home_infra.png I am thinking about adding another hAP ax². However, it only came with V7. Will it ...

phuang3

The Chinese Xiaomi has released BE3600 WiFi 7 router for RMB 249 which is about $35 USD. How can Mikrotik compete with these companies?

phuang3

Hello,

The 5Ghz channel list of Taiwan has changed. There are much more channels available now. Please update the channel list. Thanks.

phuang3

Hi Amm0,

Thanks. This is my new script to do remote-cap provisioning on certain CAP. It's working so far.

/caps-man remote-cap provision [/caps-man remote-cap find identity="RBwsAP5Hac2nD"];

Poting

phuang3

Hi! I am using caps-man to manage my CAPs. My CAP interfaces are dynamic and I'd like to remove some of them at certain time (at night time). Here is my script to REMOVE some of my CAPs. /caps-man interface remove RBwsAP5Hac2nD-1; /caps-man interface remove RBwsAP5Hac2nD-2; And, here is the script t...

phuang3

TPlink not only supports Wifi 6. Their latest flagship even has motorized active antenna! I'm not sure if this is just a gimmick, but it looks amazing.

phuang3

For those who are also looking for female RJ45 on RB450G, the 48F-01GY2DPl2NL will do the job. However, only one LED will lit. You need to manually flip the polarity of the other LED. Disassemble the metal casting from connector, and push the LED out. Reverse it and push it back. You're done.

Poting

phuang3

This device has made history! Please put it in a wall as a valuable thing and buy a new one!

In fact, this RB450G failed in just few years after purchase due to the faulty capacitors. Seriously, I'd prefer repairing it.

phuang3

Are you really wasting your time buying/unsoldering/soldering those connectors?

I have all the tools. Desoldering will only take less a minute.

phuang3

Hi, My old faithful RB450G is still working, but 2 of its female RJ45 connectors have problem. They will not hold the cable when inserted which make the connection very unstable. I tried to replace them with similar parts but none of them worked so far. They all have different pin out. Is there anyo...

phuang3

As some products only equipped with 16MB flash memory, it's very annoying to use netinstall to upgrade RouterOS every time. Please increase the flash memory to allow self-update. I think the cost between 16MB or 32MB flash chip is trivial.

Poting

phuang3

Thanks. Now I know it's arm based.

phuang3

What would be the correct install package for RB450Gx4. Misbe or Arm? The description says RB4XX for misbe, but I heard this has an arm processor inside. I will not take any risk before I figure it out.

Poting

phuang3

Problem solved. One of the RF amplifier is dead. Replaced the broken RJ45 female connector, too. http://bbs.pigoo.com/data/attachment/forum/201708/18/204245twvx98dvhfwwh1hw.jpg http://bbs.pigoo.com/data/attachment/forum/201708/18/204245p9pp4zom5qp1qg1v.jpg http://bbs.pigoo.com/data/attachment/forum/...

phuang3

I also have residential broadband of 100M/40M. An RB450G will do the job nicely unless you need wireless.

phuang3

Sorry, the correct product name is NetMetal 5, not Netbox 5.

phuang3

Hi, I got my Netbox 5 (RB922UAGS 3 ant version) working for about 18 month. Yesterday, my phone couldn't receive any signal from it. I did a reset but I can't fix it. I unmounted the outdoor Netbox 5 and it turns out the hardware is actually working but the WiFi signal is very weak. I can only get -...

phuang3

All I know is that values higher than upper limit will damage the chip. Yet, what is the upper limit? Go to the http://routerboard.com/ , click on the board you're interested in, then click on the "Brochure" link in the "More info" section. The PDF following the link should cont...

phuang3

This is exactly the question I am going to ask. It seems there is almost no information about this setting. All I know is that values higher than upper limit will damage the chip. Yet, what is the upper limit?

phuang3

I don't have the CCR, but the Atheros switch chip on my RB450G is capable of 1Gbps without sweat.

phuang3

IMHO and from experience, it is very unlikely that water will enter the device from below, even without the plug in place. Of course it is a very nice extra assurance to have. I would cut just enough for the cable to pass through tightly, and maybe consider using silicone gel if I was paranoid abou...

phuang3

On the bottom of the Net Metal 5, there are 3 rubber plugs. I unplugged one of them and inserted the network cable through the hole, as simple as that. This works without question, but the hole is big enough that I'm afraid it may affect the weather sealing capability of the device. My question is t...

phuang3

Problem with 6.31 on NetMetal 5. After reboot, I can see wireless-6.31-misbe.npk was still there and Netbox showed 6.30! Downgrade to 6.30.2 successfully, but the Netbox is showing 6.31... I got confused! After upgrade to 6.31 http://kspqm.kymco.com/ckfinder/resource/johnny/image/winbox.png After do...

phuang3

But anyway, you could just get bigger rubber antennas: http://www.ebay.com/itm/RP-SMA-2-4-GHz-17dBi-WIFI-Booster-Wireless-Antenna-WLAN-For-PCI-USB-Modem-Router-/310496344233?hash=item484b0638a9 Yes, I thought about that. However, high gain 5G antenna is very hard to find. Mostly 2.4G only. Can I us...

phuang3

Thank Normis. You have mentioned overkill, but the actual reception is just merely ok inside the house. The windows close to the NetMetal 5 are bedroom windows on each floor. Inside the bedroom, the reception is fine (mostly over -60 dbm, sometimes -40~-50 dbm), but it gets much lower if I left the ...

phuang3

Hi guys, What would be the cons if I put indoor antennas on NetMetal 5? I've to admit that I didn't realize how expensive an outdoor antenna was before I purchased the NetMetal 5, so I used 3 indoor antennas from my previous ap - Netgear WNDAP330. This unit is for residential purpose only. My house ...

phuang3

I just realized I have this problem for years. For unknown reason, the bt traffic will gradually slow down on my RB450G. At first, all peers looks fine, they have different download/upload speed. Some torrents like Ubuntu ISO will even reach the highest speed at 12000kb/sec. After some time (1~2 wee...

phuang3

This is a good idea. TILEGx8004 can replace RB1100 and making it an intermediate model between 850GX2 and CCR1009 series.

phuang3

OMG! CCR1009+PC is the one! I can't wait to see it.

phuang3

Just replace the faulty caps, you should be fine. When I bought my RB450G, I replaced those capacitors with sanyo os-con. It has been working for many years.

phuang3

I was hoping it can sustain 300M routing on small packets, but it's close. Can it be overclocked?

phuang3

we got a CCR1036-12G-4S for hotspot/gateway and the CPU usage maximum 3%.

more than 1000 Firewall filter rules
500 NAT
walled garden
DHCP server
800 Queues
95 Tunnels EoIP
about 800 clients for a total of 100Mbps/s

All that for 3%? That's very impressive.

phuang3

8x 10Gb SFP+ ports !!! Wow...

phuang3

Regardless of RB850Gx2, I am still hoping for a smaller size of CCR1009. I got my first 10M/2M line in 2010, but now it's already 100M/40M for the same price. My ISP is offering 300M/100M this year, and there will be 1G/1G residential service next year. I don't know if the dual core RB850Gx2 can han...

phuang3

I am also looking for products that run faster than RB450G but with smaller size. Last week, I got 100M VDSL installed in my house, and the RB450G is a bit busy (CPU hit 100%) if all bandwidth is reached. Before I heard of RB850Gx2, I was hoping the CCR 9 core version can have a smaller factor for r...

phuang3

I also notice that V6 has higher CPU usage. Besides, hardware switch performance is also affected. On V5.X, I can get over 100MB/sec between different LANs. With V6.x, the highest throughput is around 70~80MB/sec. (By moving huge file between Windows shares)

phuang3

Mine is RB450G. After updated to v6.4, the LAN speed dropped from 100+ MB/sec(gigabit) to merely 7MB/sec(100Mb?)! Restored to V6.2 and everything is back to normal.

phuang3

My 450G can easily handle over 100MB/sec eithernet to eithernet in switch mode. In bridge mode, I doubt you can get over 60MB traffic by merely a 640Mhz MISBE processor.

phuang3

Yes, I am aware of that. Some performance tips have been carefully checked, but still, CPU usage is high at max speed.

phuang3

My RB450G really did a good job for my home, but it's a bit slow for current 50M or upcoming 100M internet service. I got 98% CPU usage if I reach 50M downstream. I only apply priority queues, few mangle rules, no L7 or anything. The RB1xxx is expensive and bulky for residential usage (I don't need ...

phuang3

I did that, but it still happened. I've upgraded to V5.4, no help at all. A bug report was sent, hope they can fix it.

phuang3

Well, my RB450G doesn't have this problem after upgrading to v5.4

phuang3

Mine is PPPoE cleint. There are 2 mangle rules "change MSS" at the top. Sometimes, for unknown reason, they were moved to the bottom. Without them, some of the web pages can not be visited. When this happened, I have to move them to the top manually. Is it a bug? Is there anyway to ALWAYS ...

phuang3

Maybe you can specify in.interface and out.interface and than make generic masquarade. Another ugly solution will be to configure script that check ip address of the pppoe client avery defined time period and than reconfigures nat rules accordinary. I try to specify the in & out interface, no h...

phuang3

My ISP provides 8 IPs for me, but I can only get it through PPPoE client. My initial setup for single PPPoE client + masquerade is working, but I decided to have more public IPs and assign them to internal computers. In SRC-NAT, I need to translate private IPs to public IPs, but my public IPs are dy...

phuang3

Hi Fewi, You solved my problem, thanks. The WinBox did not show the empty 'connection mark' properly, that's why this rule was always in red and displayed 'Inactive'. This confused me for a long time! By the way, I still have few questions about the mangle rules. I know these rules works, but I just...

phuang3

I've been read many posts here, but I still have problem on identifying Mail,DNS and RDP packets. First of all, receiving mails from ISP's pop3 server never get recognized, throughtput is always 0 bytes. The other 2 protocols have same problem, too. My setup is pretty simple. A 10M/2M VDSL on ether1...

phuang3

Congrats on the repair. We have found that running the older RB450 and RB450G on 12vdc power supplies instead of 24vdc will make them run cooler and the caps last. Before you go about changing caps on all your RB450G boards, try replacing the power supplies instead. Tom The cause is not Vin or temp...

phuang3

Fewi,

Thanks for the quick reply.
I got one more question. If I apply connection + packet mark on any connection of http port:80 through WAN, does it mean any further incoming "and" outgoing packets are both marked? Without connection mark, I have to achieve this in both ways, right?

phuang3

A connection mark is a mark that is automatically applied to all packets of a connection. You mark the connection on one packet, and all other packets in the same connection will have the same mark. This is very useful for identifying traffic to a host as well as the return traffic... /ip firewall ...

Search found 54 matches