Tested v.6.33.3 on RB450G, RB951Ui-2HnD, RB911G-5HPnD. All show issue with PPPoE MTU. PPPoE MTU connects @ 1480 MTU and 1492 MRU. Other similar devices on the same network with 6.32.2 connect properly @ MTU 1500, and ping shows no fragmentation with 1500b packets. Downgraded @ 6.32.2 the RB450G for...

Hi
i tryed first with e1000 but it's not reporting l2mtu, so i tryed e1000e.
All others are not recognized by routeros, esxi version is 5.0

update:
if ospf area is stub, then external route are not labelled in mpls forwading table.
the only way i've managed to get it working is to use a default ospf area.

Hi all, i've setup a routeros version 6.30 under esxi envinroment. the esxi host is connected phisically to a ccr1009 and logically the connection is as below: guestROS-ether1->(e1000e driver)-->ether1-CCR1009. vSwitch MTU setup to 1600. i've set up mpls with LDP distribution, MPLS all-interface to ...

Im' experiencing the same problem.
i want to establish a VPLS tunnel between 2 router une in backbone area and other in a (totally)stub area.
The tunnel goes up but not the traffic.
MPLS distribution is LDP, no summarize prefix.
Any advice to resolve this problem ?
thanks in advance.

Thanks so much Now the motherboard sees the card Maybe motherboards released before the new AC standard have that package disabled by default so "wireless-fp" needs to be enabled manually. It is necessary that the staff of mikrotik enters these instructions in R11e-5HacD datasheet because ...

as stated in object i installed the miniPCI-e card into RB953 but routeros does not see additional wlan over its embedded. I tryed to change the mpci position to other slot but the card remains unrecognized. Also installed another new card but nothing to do. It doesn't works. Follows the output of p...

THe problem did not involved on another PC. but this behaviour is very strange.
I never had same issue first, i always used winbox with other 100+ ros devices since years..

Can someone please clarify this for me. I'm trialing ROS 6.x and got confused regarding QoS. I was running double QoS on 5.x - mangle prerouting + global-in to prioritise traffic - mangle forwarding + global-out for PCQ to give each client equal bw Just like found on many MT presentations and docum...

thank you !

Hi all, i just bought 2 unit of CCR1036-8G-2S+ and upgraded to ros 6.5 and bootloader 3.10. Winbox loader is 2.2.18 and i cannot access via mac address to CCRs. However i can login into ccr without problem via mac-telnet from RB751, so i also tryed to reset configuration skipping default-configurati...

samsung172 Your citation does not mention any reference to SFP+. I basically ask if the S+31DLC10D has dual fiber support or dual band communication in case of sigle fiber. I guess the possibility are 2: 1) Single Fiber connection with dual labda. 2) Dual Fiber connection with Dual LC and single lab...

Hi All
im wondering if this sfp+ module has a double LC connector and so full duplex communication because
the official product page states LC connector without any reference to Dual LC connector.
Is S+31DLC10D supports 2 fiber connection ?
Thanks

Thanks to your feedback in v6.0RC3 we will have some changes in QoS features. We made simple queues completely independent from "Global" queue tree. Now simple queues will happen after "Global" queue tree: packetflowv6.png So there is no more need to remember who will get traffi...

i've the same problem exactly.
it is supposed to act as described in DOC but is not

Hi all, i'm actually using usermanager to handle a network with 50 user online averagely in a hotspot system, while using it with a single nas works fine, using multiple nas with multiples hotspot generates some error of hotspot login, navigating in UM logs i recognize this: if a user login to nas A...

The problem, BUG instead, persists on version 5.17, this is very annoying, if someone knows an easy workaround would be nice ! i've a mesh network topology, it consists of over 50 wireless nodes connected together, some link is p2p someone p2mp, ospf network-type is broadcast. actually every day at ...

Hi all, i would like to upgrade my sxt board with the last legacy firmware 4.17 since i had some problem with 5.x.
The official download page show me only 5.5 version so the question is: rb400 series firmware can be used instead ?
thanks in advance

Hi all, i've a hotspot system with 2 interfaces, WAN and LAN in which the hotspot is installed. in the WAN segment there are multiple PC used by secretaries who want get some information about the users of hotspot, such remaining-uptime and expiring time. Is there a way to access the login/status p...

it's a BUG!
all openssh system handle it correctly.

same problem

Hi all, i've a hotspot system with 2 interfaces, WAN and LAN in which the hotspot is installed. in the WAN segment there are multiple PC used by secretaries who want get some information about the users of hotspot, such remaining-uptime and expiring time. Is there a way to access the login/status pa...

Hi all, i would like to know via console the status of a particular user in user-manager such uptime-used, uptime-left and other info. how i can obtain these variables by inserting a username to match a regexp? the goal is to write a shell script that take the username as input and execute the query...

i dont know what exactly does openssh, but in previous version of mikrotik im sure of the ability to login both via publick key and password too.
Seems a bit strange that using authorized_keys in a user account prevents log in from other hosts/users that specified in pubkey.

i cant obtaing admin login via ssh using password. other users can login so the ssh service seems ok, the client used is open-ssh in a linux envinroment and it reports invalid password while the log from mikrotik reports nothing. i also tryed on the same mikrotik machine via /system ssh 127.0.0.1 bu...

i've upgaraded from 4.13 to 5.1 and then to 5.2 on a x86 system;
now i can't access via ssh with admin privilege using password but using ssh-key still works ok.
i tryed by creating other users and i've no problem to login with passwords.

Another issue:
a new added Profile from usermanager (web) defaults to start-at=now attribute and the web interface always show "start: Now" for others profiles with start-at=logon too. Theres no way to change the Start attribute from the web

i have the same identical problem.. i have upgraded from 4.13 to 5.1 and when i loaded back the usermanager backup file (through /tool user-manager database load) the cpu grown to 100% for about 2 hours. The user profiles have become inconsistent and i had to change it manually to reflect the olds o...