Here you can find the answer http://forum.mikrotik.com/viewtopic.php?p=421416#p421416 sent from my mobile phone using tapatalk Dear Friend, I read this link but i did not find any solution from it they want to communicate TCP and using different ISPs. But I am using same ISP and same Speed Internet...

Here you can find the answer http://forum.mikrotik.com/viewtopic.php?p=421416#p421416 sent from my mobile phone using tapatalk Dear Friend, I read this link but i did not find any solution from it they want to communicate TCP and using different ISPs. But I am using same ISP and same Speed Internet...

Dear Friends,

I am looking for the solution for Mikrotik Router where I can use one WAN port for only Up-link and second WAN port for only Down-link Please guide me how it could be configured


Looking for your reply


Thanks and regards

Dear Fellows, I have a problem and can not get how to override on it. I have a remote site with Mikrotik 750 router with Live IP 202.146.X.1/29 and 2 Wireless device one is AP and second is client with the IP address 172.20.60.2/29 and 172.20.60.3/29. What I need is that I want to connect these wire...

Try to add MPLS in you setting it will work fine and you will get good speed

Dear friends

I have 2 connection from one ISP

1 is on fiber optic
2 is on wireless ubnt radio

what kind of configuration should i made in my RB that if 1st link get down second will come automatically switch over the link

thanks for help in advance

Plz make a copy for me at askcom.pk@gmail.com

Dear Brothers, I am looking for a solution for the following needs 1. I have 4 VOIP gateways in different location. 2. These are connected with the same ISP using PPOE(DSL) Because I need to use only the Physical network of ISP. With VPN dialer 3. My Main site has one Mikrotik router with static(liv...

Dear Friends,

Please tell me the code to establish a Bridge connection. One on ISP site and one on client site.

ISP assign me the 3 Live IP address

I have these 3 Live IP's xx.xxx.140.138,xx.xxx.140.139,xx.xxx.140.140 and the Gate way is xx.xxx.140.129

Please help me

Dear fewi, Remove the 10 dot addresses, they are unnecessary. You don't have a point to point routed link, you're bridging. Assign the public IPs directly to the bridge1 interfaces. Then try again. What IP address on the public IP network is the default gateway for clients? I can not get what you wa...

Here are the detail as you demand Bridge Side Configration > ip address print detail Flags: X - disabled, I - invalid, D - dynamic 0 address=10.10.0.1/30 network=10.10.0.0 broadcast=10.10.0.3 interface=wlan1 actual-interface=bridge1 1 address=90.0.0.10/24 network=90.0.0.0 broadcast=90.0.0.255 interf...

Dear Friends,

Yes I have set the routing table as well but can not resolve my issue.

I only configure my router's Wireless, Bridge and LAN interface IP nothing else has been set.

but still unable to get connected. I even can not ping my remote AP's LAN IP as well.

Dear friend

every thing is set accordingly because it is assigned by the ISP and there is no doubt about it because I am pinging the Gateway as well.

Dear Friends I have setup a 1km wireless link with the help of RB433AH having 23dBi Grid antenna as client and RB433AH having 12dBi Omni antenna. everything working fine i can ping and test bandwidth it is perfectly fine and getting 8Mbps speed on average. But the problem is this that i have assign ...

I need to establish one link PTP 4Km I am using these equipments to establish the connection Bridge site: RB433AH (4.11v) with 12dBi Omni HG5812-Pro made by L-Com and the height of the site is about 140ft Station Site: RB433AH (4.11v) with 29dbi Dish ANT5158D29P made by Lanbowan Frq. 5150-5850 and t...

try to downgrade this to the older version 5.2 may not work as you required

here is the detail of my wireless interface I have change my SSID name to teamW but no affects [admin@MikroTik] /interface wireless> print Flags: X - disabled, R - running 0 name="Wireless" mtu=1500 mac-address=00:0C:42:60:15:8B arp=enabled interface-type=Atheros AR5413 mode=station ssid=&...

Dear friends,
I am trying to connect my Station with the Bridge my signal quality is as under

I am trying to connect grey12 Bridger but I cannot get registration


Waiting for reply