MikroTik

draguzet

Any news about FCS error, we have on all CCR routers connected to Cisco Nexus 1064

draguzet

Has anyone tested a new WAP60g x3 with Lite60 on production ?

draguzet

Hi ! We have CRS328-24P-4S+ for POE up device, and CCR1016-12S-1S+ for Fiber connectivity. On network are OSPF enabled, so till now we have on AP units (NetMetal) set Ether1 and SFP port to bridge with higher path cost to Ether port, so we have failover if Fiber drop or Ether drop for some reason, d...

draguzet

I just set up a GRE tunnel without IPSec and I cannot get past 60mbps. I watched the profiler on both server and client and the CPU usage is very minimal. Maybe GRE is my solution if I could figure out why I can't get it past 60mbps Hi ! Same problem by me, have you solved IPSEC or any tunnel with ...

draguzet

Which hop drops the speed, the first one (core<->POP1) or the second one (sector<->subscriber)? I'm sure you're aware that there are some issues using NV2 on ac-capable routerboards (most notably ARM-based) ... there are plenty of posts in this part of forum. Drop are on whole route test Subscriber...

draguzet

Hi ! Do you have noticed problem with NV2 that even on easy setup, like below (one main link, with 150 Mbps TCP test, on remote side sector with connected for test 1-2 subscriber, and test to device POP1 are 100+ Mbps). Problem are that Btest from Subscriber to CORE router are 30-40 Mbps MAX ?? CORE...

draguzet

I didnt do full speed test on them just speed test at home on iPhone

-70 are not so good signal at 800m distance ?? I'm realy amazed that with this low singnal link are UP on heavy rain. We have links with -55 signal at same distance and on light rain are droping !?

draguzet

We have problems with CHR, after adding second CPU core to instance CHR are crashing with error:
do_IRQ: 0.193 No irq handler for vector (irq -1)
etc..

draguzet

How much rain? For my experience 40mm/h of rain is enough to kill a 1000m link

No, little rain, maybe 10mm/h

draguzet

frequency?

We have problems with link droping on rain...tested even on beta28, used even align command, but no luck...not stabile at all...signals great (-52/-55 on 1150m link distance).

64800 and 58320 same problems...

draguzet

We have problems with link droping on rain...tested even on beta28, used even align command, but no luck...not stabile at all...signals great (-52/-55 on 1150m link distance).

draguzet

The same here. My RB750GL is gone. Bricked. LED is blinking as it should but Netinstall never gets anything from RB750GL. That's third time in 7 years of working with various MT's but this time I just can't do a thing. Any sugestion? Try this: 1) Power your device off; 2) Power device on; 3) Press ...

draguzet

Same situation, described below: 1. After upgrade to 6.43.2 device are unreachable, boot up properly but not working. 2. I try to reset on default, and is passed, but same problem 3. Wifi are powered on with default SSID, after I try to connect to wifi stop working 4. LAN led are green even I disco...

draguzet

On mipsbe devices with AR8227 switch chipset (100 Mbps 5-port routers like hAP, hAP ac lite, hEX lite, hEX PoE lite, RB951Ui-2Hnd, OmniTik 5) it seems you can damage the routerboard after upgrading it to 6.43.2 and using no-default settings... Anyone experienced physical Ethernet port problems afte...

draguzet

Just upgraded RB951Ui-2nD from 6.42.7 to 6.43.2 and it's bricked. Netinstall does not see it. I've upgraded it from winbox system -> packages -> download and install. What could be a reason and is there any way to ressurect bricked device? Narian, what is the behavior of bricked device ? I have sve...

draguzet

Just upgraded RB951Ui-2nD from 6.42.7 to 6.43.2 and it's bricked. Netinstall does not see it. I've upgraded it from winbox system -> packages -> download and install. What could be a reason and is there any way to ressurect bricked device? Same here, repeated on 4 devices :(, copy paste .npk file, ...

draguzet

1750m LHG60 ROS 6.43
lhg60 1750m.png

Freq:
58320 -59
60480 -63
62640 -62

We are suprised also with results (Signal) from Lakis ? Can you please share procedure to align, we have difficulties with proper aligning LHG 60G...

draguzet

Same here, on 5 devices, all on 6.42.7, all controled by CapsMAN !!
Mikrotik !?

draguzet

Link is good, With „center“ in the TX Info Field then you are aligned 100%. We tried it with a 1800m link and getting one side to center the other not. I don't understand TX / RX sector values? Which side to align, and what are these values represent? How to align AP side if there is no info about ...

draguzet

First (i think that is first :)) LHG 60G in Croatia linked today...picture and results below. We would like to have more info about signal/allignment, and if is results that we have OK or it must be better (signal and speed). For now we can see problems with U-bolt, same as on DynaDish that, after o...

draguzet

What with NV2 sync ?
Is someone use in production NV2 sync (master-slave) and reuse same frequency on "behind" sectors on the same tower ?
Are this function work OK or not ?

draguzet

Thumb up for that review...we are WISP and working only on NV2, as the post above says, logically that NV2 has to give the best results, so please MT let us know the recommendations of the settings as described below: Some other observations and suggestions from my side: if it's key point here - don...

draguzet

What is final conclusion for best practice setup after this update ?
TDMA Period: fiksed 2-3-4 ms or Auto ?
Fixed or Dynamic downlink ?

draguzet

How to upgrade AP's automaticaly over Capsman when missing Wireless-cm2 files in new version ROS ?

There is error in log, because of missing file...

cpasman.png

draguzet

OmniTik POE and CRS125-24G-1S-RM after update not booting, reboot loop ?? After netinstall all OK !

draguzet

And profile of CPU usage: NAME CPU USAGE pptp all 1% firewall-mgmt all 0% spi all 1% ethernet all 1.6% console all 0% firewall all ...

draguzet

yes, pppoe over 100 Mbps.

Interface load below and +400 PPTP inbound interfaces of customers that are not screen-shoted.

interface.png

draguzet

Why you think it's a NAT trable? 60% good load! You are network monster! Maybe connect second device in active-active mode? Also try update to current! Why I think that is NAT problem, because as I told before there is not hard firewall, not so much mangle, and only thing is NAT and change MSS on p...

draguzet

Without IPSEC... uptime: 1w6d15h35m3s version: 6.34.4 (stable) build-time: Mar/24/2016 13:13:08 free-memory: 1650.1MiB total-memory: 1956.2MiB cpu: tilegx cpu-count: 9 cpu-frequency: 1200MHz cpu-load: 63% free-h...

draguzet

Have you any queue and routing rules ?

Sure, i have Queue for each customer (connected by pptp), and routing yes, rules no.
But on profile i see that Queuing are not using too much of procesor...

draguzet

I have only 20 Firewall rules, and yes accept established,related are on the top...so I try to disable all firewall rules but no change.
I have mangle, but only 2-3 IP address are affected by mangle rule.
On top of Mangle rule are change MSS for PPP, so that is all...

draguzet

We are small WISP, and using CCR1009-8G-1S-1S+ for core router where are terminated all users (pptp), and this is point of Queue-ing and NAT-ing. So, are this RB too weak for traffic of 300 Mbps and more, and have 35.000 connections, because CPU are over 50-60% on this usage, and most of CPU are usi...

draguzet

Authentication by PLOAM password This requires a method for setting the Registration ID in the ONU from which the password will be generated. This is NOT supported by RouterOS. Therefore, RouterOS currently prevents deployment of the GPON ONU module in full compliance with ITU-T G.984 standards. Is...

draguzet

Test by new firmware..

TCP or UDP traffic ?

draguzet

I am guessing that screen may be related to some type of a PPOE login. Where the device/user has to supply a login & password to connect to the network. This really has little or northing to do with the ONT serial number seen at the upstream ISP. No, this password are not PPOE login, these are ...

draguzet

I do not understand, why is not possible to make configuration of GPON, like TP-link GPON adapter have, http://www.tp-link.com/res/down/doc/TX-6610_V4_UG.pdf , because there are obviously many ISP that require this autentification to work with GPON

gpon.png

draguzet

In Croatia, also we must enter password in ONT to work with provider...but Mikrotik have no option for this ?

draguzet

What if we need enter password for ISP to work with it ?
There is no option to enter password, like on TP-Link GPON external device ?

draguzet

Hi ! Is there any information about antenna polarization on QRT (2 and 5), and Dynadish on chains (CH0, CH1), because we try to connect DynaDish as client to Vertical polarized GRID, and signal are disaster. If we turn Dynadish for 90 degrees signal are ok. We have this situation even both chains ar...

draguzet

Same problem...any info about solution ?

draguzet

Your posts are not related with topic title. Please start your own Topic.

I think that my problem are NV2 related ?

draguzet

Speedtest JUMP from base station to earlier client when "one chain" user stop transfering...

speedtest_jump.png

draguzet

We have problem when client with "one chain" antenna are connected to MIMO sector. Speed are dramaticaly fall when "one chain" user start transfer even small traffic, pictures below: Speedtest from base station to one Client (dual chain SXT) speedtest_good.png Speedtest from &quo...

draguzet

Same situation, performanse degradation are obvious, and users complaining every day

(

Mikrotik ??

draguzet

And BIG BIG problem on Netmetal (922 and 921) devices are unstable LAN port, which suddenly stop working even all parameters are UP and running, but only solution is to reboot device one or more times.
We are waiting Mikrotik to solve this BIG problem for Months

draguzet

We have similar experiences, better throutput (140 Mbps of TCP) , but big difference between UDP vs TCP (300-400 Mbps on UDP and 140 Mbps on TCP). But even this 140 Mbps are low because of marketing material that say 800 Mbps ?? As we are testing on different links (with and without interferences) t...

draguzet

IP Pool: Pool name 1 in radius and IP pool in mikrotik must be same.

Can you post the screenshot of radius and mikrotik?

pptp.png

radius_profile.png

draguzet

Try to uncheck Advertise 1000 Mbps Half and Full settings on the ethernet interfaces of the netmetals so that it negotiates at 100 Mbps. If that works way better, try to play with Tx/Rx Flow control on 1000 Mbps too. Let us know the results. What setting do you have for NV2, TDMA Period ? Try set t...

draguzet

Hi ! We are using RouterOS RADIUS to authenticate users over PPTP connection and would like to assign IP address pool through "profile" of user, but not working. On Radius "profile Limitations i try to set "Contraints" - IP pool: "pool name1" , but when client conn...

draguzet

Hi !

Is possible how to setup through CapsMan Advanced wireless settings, like "distance" (to indoors...) ?
I think that is mandatory to add in features !

draguzet

What setting do you have for NV2, TDMA Period ? Try set to 1ms, I have much better performanse on 1ms vs "auto" or higher values. My question for experts, and Mikrotik staff, are that I experience better performance on 802.11 vs NV2. Link are 11km, with mANT30 + NetMetal5. Nv2 - 100 Mbps l...

draguzet

Here are config.. /ip route add distance=1 gateway=10.50.0.1 routing-mark=ZG add distance=1 gateway=192.168.10.2 /ip firewall mangle add action=mark-connection chain=forward connection-state=new in-interface=\ pptp-out1 new-connection-mark=connection add action=mark-connection chain=prerouting conne...

draguzet

I have router with 1 default gateway (for internet), and another gateway with public IP address. I would like to make port forward from public IP address to local, but not working because of different default gateway. I'm try to setup this with connection mark, on inbound port (public), and make rou...

draguzet

We have BIG Wireless problems on 2.4 band: 1. Channels 2412, 2417, 2422, 2427 are missing on regulatory domain and manual-tx-power, country are Croatia ? WTF ? 2. Cusomers with R52Hn cards have low throughput, very low ( below 1 Mbps), on same location we have Backup AP on 6.22 and throughput are 30...

draguzet

I try this strange setting and working ok, are this usable for production ?

RB1 have IP: 10.10.30.10 – NETWORK: 192.168.76.55
RB2 have IP: 192.168.76.55 – NETWORK: 10.10.30.10

and ping are working ?

draguzet

Router OS ver. 6.xx are not working on XEN Virtual machine, 5.26 work ok ?
Are this problem solved or in process ?

draguzet

Hi ! We are working on Hotspot's for town, and all working OK on "normal" days, when city are not occupied with 4000-5000 people. But when is any event on city (concert etc..) , we are experiencing poor performance on wireless network, like high ping (400-500 ms), and often disconnect form...

draguzet

Here is PING testing, with static IP on routers...

draguzet

Hi !

I have 2 MT on Public IP, and Eoip between them, and local ETH in bridge with EOIP.
If DHCP server are on MT1, and PC are connected on MT2 LAN, DHCP are not working...Dhcp debug log are in attach.
For testing on MT2 LAN are connected another MT with DHCP client !

Help.

draguzet

I know how to "forse" OSPF mode with "copy" of dynamically created inteface, but question is why some router make dinamically PPTP interface to "broadcast mode", and some to "point to point" ?

draguzet

Hi !

I have some locations that connect to central VPN over PPTP, all working but on some locations PPTP link are set to point-to-point on OSPF, and on some location on "broadcast" to default ?
How to force all to Broadcast automaticaly ?

draguzet

Same question by me, any info about this ?

draguzet

Hi ! I have news about high latency...but I don't know what is reason for this behavior. I power up Snooper on another card, and see that usage of Freq. are high on this time high ping, but is not visible that is any client using it, because is on same MAC as AP card is ?? Picture in attach ! What m...

draguzet

Hi guys ! I have same situation, problem are escalating to me over time :( I also see that Bittorrent kil AP with connections, and open Topic recently: http://forum.mikrotik.com/viewtopic.php?f=14&t=59823 We have for redundancy dubble setup, 2 x 2.4 for clients, 2x5 Ghz for connection with centr...

draguzet

Hi ! I have problem on Base station similar to this thread: http://forum.mikrotik.com/viewtopic.php?f=7&t=46374 , it seems that my problem is also torrent user's :( First I put this rule (10.52.152.0/24 = wireless users network) add action=drop chain=forward connection-limit=100,32 disabled=no p...

draguzet

Any other advice for script improvement to save/compare current IP address without creating html file ? Run it every 5 seconds, 5 minutes, or 5 hours... don't fetch unless the IP has changed. Here's the script I use and run every 5 minutes. The current IP is stored and used to compare next time the ...

draguzet

why run the script so often? run it less often This is ADSL, reconnecting are possible in any time, and on this line are PPTP VPN for bussiness work and if connection are re-eastablished in working time I need smallest time to reconnect VPN again :( But this is not subject of question, I can set ev...

draguzet

Ok, now is all log commands commented, but one line in log are generated

Is any chance to remove except that disable "info loging" in settings ?

draguzet

I know it I use this script, and set # on all log info's, but this is always on log *** fetch:file "dyndns.checkip.html" crated UpdateDynDns: No dyndns pdate needed *** Here is modified script: # Set needed variables :local username "user" :local password "pass" :local ...

draguzet

I use this script, and set # on all log info's, but this is always on log *** fetch:file "dyndns.checkip.html" crated UpdateDynDns: No dyndns pdate needed *** Is no need to be on log, and i would like to remove completely log about dyndns, only successfully change may appear on log. How to...

draguzet

Hi ! I have RB with 2 different ISP. Each on different LAN port, and different IP address. LAN1 - 192.168.0.1 - ISP 1 - LAN1 have address: 192.168.0.3/24 LAN2 - 192.168.1.1 - ISP 2 - LAN1 have address: 192.168.1.3/24 ISP2 is configured to forward from public address ports 1723, 3389, 3390... to loca...

draguzet

LOCATION 1 - RB433AH - R52n-M - GRID27 - 5Ghz <---------------> LOCATION 2 - RB433AH - R52n-M - GRID27 - 5Ghz LOCATION 1 (link2) - RB433AH - R52n-M - GRID27 - 5Ghz <--------> LOCATION 3 - RB433AH - R52n-M - GRID27 - 5Ghz Distance between are 30 km LOS and another link 12 km LOS. On both links i have...

draguzet

have you got both wireless interface cards in ONE outdoor enclosure? I strongly suggest one one wireless interface per metallic (shielded) outdoor enclosure, due to self interference issues. Yes, if I say that cards are on RB433, all cards are on same enclosure. Our experience is that this is not p...

draguzet

550Mhz channel separation should be more than sufficient to stay out of interferences problems. But what about other channels fm nearby AP's? Or are the cards not getting too hot? No nearby AP's, location are rural. Show us your wireless settings (CLI: interface / wireless / export) Start playing w...

draguzet

Hi !

We have one setup (antenas are on picture in attach):
RB 433AH
R52nM x 3

Problem is that when client or clients (1-2) are connected to Omni antenna, link that is on GRID antenna is degraded (from 40 Mbps to 5-10 Mbps). Frequency are 5850 for Omni, and 5300 for GRID, but no luck ?

DSCF9900.jpg

Search found 75 matches