Community discussions

MikroTik App

Search found 8 matches

by mfguney
Sat Jul 16, 2011 5:32 pm
Forum: General
Topic: How to enable system health ?
Replies: 9
Views: 8488

Re: How to enable system health ?

Is it really even working on your other machine? What I mean is, if it is an x86 (PC) where are the +12 and +5 volt rails? what is it monitoring in the voltage? Also, what the heck is reading at -2 degrees C, is this board outside in the snow? Sorry, I know this really doesn't help, but it seems st...
by mfguney
Thu Jul 14, 2011 10:05 pm
Forum: General
Topic: How to enable system health ?
Replies: 9
Views: 8488

Re: How to enable system health ?

NOT working on X86 I have routerboard and x86 MTs and this feature working on all of them except one that I have mentioned this topic. For example in following hardware i can see the system health menu. MB: Gigabyte GA-G33M-S2 CPU: Intel Core 2 QUAD Q8300 HDD: 160 GB SATA NIC: Mikrotik RB44GV PCI 4...
by mfguney
Thu Jul 14, 2011 4:01 am
Forum: General
Topic: How to enable system health ?
Replies: 9
Views: 8488

How to enable system health ?

Hello, I have setup a new x86 MT box. Everything normal but /system health not working, it says disabled (i have attached screen shot). How to enable "system health menu" to see voltage, temperature and fan speeds? My configurations are following: MB: Intel Desktop Board DH61WW CPU: Intel Core i7 26...
by mfguney
Sat Jul 09, 2011 3:32 am
Forum: General
Topic: Simple question about command line
Replies: 4
Views: 656

Re: Simple question about command line

That means there is no interface called "ether1" to assign the IP addresses to. I had assumed there was since you used that name. Replace that part with an interface name that actually exists. You are right. I renamed one of the interface as ether1, and your command worked! Thank you very much for ...
by mfguney
Sat Jul 09, 2011 3:16 am
Forum: General
Topic: Simple question about command line
Replies: 4
Views: 656

Re: Simple question about command line

/ip address { set [find] interface=ether1 }; Thank you for your reply but I got following error: [admin@mikrotik] > /ip address {set [find] interface=ether1 }; input does not match any value of interface Here my address list, there is 188 entry exists now and will be growing. I want to change all (...
by mfguney
Fri Jul 08, 2011 9:39 pm
Forum: General
Topic: Simple question about command line
Replies: 4
Views: 656

Simple question about command line

Hello, When I restore backup of one MT device to another, interfaces of all IP Addresses will be "unknown" since ethernet devices are different. Then I have to manually edit all of them. I think this can be done by simple command on terminal, but I am not familiar scripting of MT. For example, I wan...
by mfguney
Thu Jul 07, 2011 1:32 am
Forum: General
Topic: RouterOS 5.5 Released
Replies: 47
Views: 13076

Re: RouterOS 5.5 Released

@mfguney Set your simple queue to specific interface, not to 'all', and this error will disapear. Torch tool can monitor one interface, not all, at the same time in one window. HTH, Thanks for reply. I have already tried but not working. Src. Address always be "0.0.0.0/" and giving same error. We o...
by mfguney
Wed Jul 06, 2011 11:42 am
Forum: General
Topic: RouterOS 5.5 Released
Replies: 47
Views: 13076

Re: RouterOS 5.5 Released

[Torch error in V5.5] If you rigth click a queue and torch, Src. Address field will be empty in torch window and giving error. You must write source address manually if you want to torch a queue record. I have attached screen shot of error. This error has been occured in all of our Mikrotik devices ...