MikroTik

Estiaan

I got a strange problem Ive recently started to use NBMA on my ospf to route between my 2 networks. all my client routerboards gets authentication from the radius server (192.168.4.x) What happens is every now and then the client routerboard cannot see the radius server, as soon as I open New Termin...

Estiaan

Ive got 2 OSPF routed networks the first is in the 192.168.4.32/29 from there ive routed the network out to different subnets" /29, /30" on my highsite, but all my networks setup on /routing ospf networks are in the "backbone" area. The second OSPF Network is running in 192.168.2...

Estiaan

I am using Both Adresses and Ports, so far all my youtube streams no problems, I have not yet tried all the banking sites, tho I know FNB works perfect, I think ABSA might be an issue. What I have also seen is doing a speedtest using Both Adresses and Ports, "bonds" the PPPOE aswell, I was...

Estiaan

So I put a normal 8 port switch between my routerboard that handles the PPPOE connection and the pysical adsl modem?

Then I setup an Vlan between the Routerboard and the adsl, each with their on VLAN TAG?

Estiaan

Where I live in South africa, there is no Fibre in an 600km Radius. I use mangle to mark different clients with different routing marks.

If I use Vlans how would I go about setting that up?

Is there a way to connect a secont RB1100AH to add more ports?

Estiaan

We have an OSPF Network, where I use an RB1100AH as my edge router At the office we have 8 WAN ADSL Lines, and 2 LAN POrts for different sides of the network. Just an question, if our network grows at the current rate, we will need to add more DSL lines to our network, and our RB1100AH only has 12 P...

Estiaan

We are in the process of getting a fibre link for our small WISP, now on our network we allow P2P but with low priority. I dont want out clients to start downloading P@P on our fibre link, as that will just be killing our bandwidth, so I want the clients that downloads P2P, to be tagged, and thrown ...

Estiaan

1.1.1.1 is the IP address of the Cisco(ADSL) routers address
1.1.1.2 is the IP address of my mikrotik router.

thats why the gateway on my mikrotik is 1.1.1.1

Estiaan

Hi Ive got 2 Public ip blocks ex. 1.1.1.0/29 2.2.2.0/29 These 2 public ip blocks comes from the same ADSL router, which is a cisco bonded solution. the ADSL router has addresses 1.1.1.1 and 2.2.2.1. On my mikrotik router where I set the other 10 public ip addresses ex. 1.1.1.2-6 and 2.2.2.2-6 on eth...

Estiaan

That is the exact script I used,

Janisk, how would I change the script to work on the Rb800?

Estiaan

Hi

Ive seen a voltage monitor script in the wiki that im trying to implement on my RB800, with no success.
Anybosy else have a working script?

Estiaan

Hi Ive got a strange problem, where I got 60 clients connecting to my 5Ghz NV2 AP, Traffic on the WLAN Card is only 3M TX and 1M RX at anytime. CCQ for all my clients range from 90 to 99% at any time. Problem is, Client can recieve (TX) from my tower at full speed assigned to them no problem, But On...

Estiaan

Hi

Have you tried setting your ppp server to - 1 session per host?

In winbox go to PPP then to PPPOE Servers. Open your Service, and tick 1 Session per host

Estiaan

Hi, attached is my issue.

This is a brand new 433L routerboard, Connected to an 433uah

Both are running 5.20 with fw 2.41

Any Ideas?

Estiaan

Happened again, look at the profile. I am not running SNMP,usage just spikes to 100% by "Management"

Estiaan

I tried that a few times allready, it just loses the firmware

Estiaan

Im running 5.20 with 2.41 firmware

Picture shows what its doing, does not show Current Firmware, only upgrade firmware

Estiaan

Ive got 1 specific RB433 that reboots every hour, due to an kernel failure On it ive got 3R52hn cards, 1 is disabled. \ The board was working perfect for a year, and now all of the sudden this happens. I use 12VDC and Ive got 2 other rb433's connected with that one on a mountain. Ive got 350AMp Hour...

Estiaan

Thanks, I got it working with in Interface

Estiaan

Is there a way that I can add 2 routers with default gateways on different sides of the network?

And divide the traffic between different routers?

Estiaan

Thanks troy!

Now when I run that script, it logs and seays my WAN ip changed to x.x.x.x

But when I check address list, there is no IP there.

Should I create an address list first?

Estiaan

Is there any way of building a script, or something, to check the ip of an certain interface in mikrotik, and update it to a adress list?

For Nat rules with a dynamic ip?

I tried the In-interface, with no luck

Estiaan

Is it possible to let your Mikrotik router v5.20, be able to update your dyndns account with a gateway that has got a routing mark, Ive got 3 Wan links on 1 router, with routing marks for different subnets, now I need 1 of those lines to update a dyndns account for me. I tried the scripts, but I don...

Estiaan

Hi Ive got an setup where my clients got 3 different ip ranges (10.5.60.0/24 ; 10.5.65.0/24; 10.5.70.0/24 My firewall with 3 WAN lines ip - 192.168.4.34/29; 192.168.4.50/29 and my squid box - 192.168.10.254 My Squid has got an WAN and LAN (WAN - 192.168.4.54/29, with gateway 192.168.4.50) LAN (192.1...

Estiaan

It reboots bout twice a day.

Then health says 76C and 11.7V

Estiaan

My RB800 is running at 75C, is that close to overheating?

Estiaan

Can one connect one R52hn - dual chain, with each chain to a different 24dbi grid, 1 in Vertical and 1 in horisontal?

Is that possible?

Estiaan

Ive got an few towers on which I run OSPF. Now all these towers are connected using /29 and /30 addresses. Ive then got an RB at the Base which is connected to an ADSL modem, Which has got an Masquerade rule on in. Each tower also needs the masquerade rule on it, in order to supply my customers with...

Estiaan

Hi n21

I cannot bridge the adsl Router, my ISP, does not allow me to log in to that router at all, There must be another way for that router to be reachable all over the network?

Estiaan

Hi n21 Ive got a last question Everything is sorted now, and Routing is working perfect. I had a few customers that I mangled their packets, and added them to a specific routing mark, to go through a different line the router where my adsl line is goin to is 192.168.4.34/29 then I got another ADSL M...

Estiaan

Check Ip address's + ospf network setting + dns setting on both sides of the PTP and bridge is fully disabled The only thing still in a bridge is the 3 ether's In (DMZ) Which the IP is on the Bridge. I can Ping the AP Bridge > Station After it connects, But I cannot ping any board further than that...

Estiaan

Ok evreything is in place, no more bridges at all, all the routers are reacheable. 1 last problem, Whenever I take my PTP link AP-Bridge > Station. All the routers becomes unreachable. It only works on Station Bridge mode. OSPF picks up all the neighbours. and Internet is working on all the towers. ...

Estiaan

I recently changed my network over from an bridged network to an routed network with OSPF. Everything is workin, except my users that authenticates using PPPOE and Radiusmanager, wont authenticate at all when My masquerade rule is on, that is infront of my ADSL modems. When I disable the masquerade ...

Estiaan

Sofar i got it working nicely, last question.

For my PPPOE server that hands out addresses - 10.5.60.1-10.5.60.254 can I setup OSPF Network as 10.5.60.0/24 ?

Estiaan

/routing ospf network add area=backbone disabled=no network=192.168.4.128/30 add area=backbone disabled=no network=192.168.4.0/29 add area=backbone disabled=no network=192.168.4.16/29 add area=backbone disabled=no network=192.168.4.132/30 /routing ospf network add area=backbone disabled=no network=...

Estiaan

What I do see tho is, I am busy setting up all the new IP's and some of my routerboards picks up Neighbours. most of them don't pick up anything, even if I add the network is /ospf networks

Bridging is still enabled so you can ping each new 192.168.4.0 addresses

Estiaan

This is my one towers config /interface bridge add admin-mac=00:00:00:00:00:00 ageing-time=5m arp=enabled auto-mac=yes \ disabled=no forward-delay=15s l2mtu=1526 max-message-age=20s mtu=1500 \ name=bridge1 priority=0x8000 protocol-mode=none transmit-hold-count=6 add admin-mac=00:00:00:00:00:00 agein...

Estiaan

Can I setup this while on an bridged network? Where wlan01 and eth01 is in a DMZ bridge?

Can I setup one address ex 192.168.4.5/30 for a bridge running (eth1, eth2 and eth3)

Estiaan

Thanks n21

So I cannot change all the IP addresses using 192.168.4.0/24

ex
Tower 1
wlan01 - 192.168.4.1/24
eth01 - 192.168.4.2/24

Tower 2
wlan01 - 192.168.4.3/24
eth01 - 192.168.4.4/24

Where tower 1 connects to tower 2 using - wlan01?

Estiaan

When you say create an vlan, what do you do with wireless links, do you create an tunnel?

Estiaan

Map.jpeg Ive got an Large Bridged network, with an single broadcast domain (192.168.3.0/24) Ive got about 10 towers, and around 150 clients.with an average usage of around 10mbps. all my clients connects to my towers using pppoe, and radiusmanager asigning private ip's to each client. Up to now all...

Estiaan

Hi Ive got an wireless link that occasionally drops cause of interference

Can someone help me with an Script to enable an wireless interface if another interface goes down?

Estiaan

I have got an RB800 with 3 sectors, and have about 75 clients connected, totalbandwithis about 12Mbps. My routerboard only uses max 10%cpu

How many client can I connect on that 1 board?

Estiaan

I have got an few DMZ bridges between my AP's

In the bridge there is are 2 Wlan and 1 ethernet, as soon as I enable ospf, it becomes non reacable, then I have to set it back to WDS to access it, is there an easier way of setting up OSPF?

Estiaan

When I try to disable it, is still stays passive?

Estiaan

I am new to OSPF, has been setting up ospf on my local network, works fine on all of the boards, except one, thats keep being passive. I cannot disably the passive at all? How can I fix this?

Estiaan

Can you perhaps tell me howd I go aboutsetting routed network up,

at the moment I use WDS and bridging, but it seems to give me quite abit of problems.

I am using 192.168.3.0/24 range for entire network, as soon as what I disable the WDS, i cannot log into my router.

How do one set that up?

Estiaan

Yes it is

Estiaan

I have got about 20 Mikrotik AP's on an WDS network, which provides internet o about 100 users.

for the last few days, everytime i try to login to Winbox on any router, the first 2 times it gives me an error message Router has Disconnected, it never used to do that, Can it be from WDS?

Estiaan

at the moment i got 18 AP's with 70 users, and for some reasontoday, everytime i try to log in via wnbox, before it logs in I get an router has disconnected message

Estiaan

How many Mikrotik devices can I have in an WDS network? before it gets unstable?

I am using all my Mikrotik AP, in an WDS network

Estiaan

Ok I checked

NV2 is on 5180

Nstreme is on 5580

That is far apart, and still does it? Will it be better if I Build the Nstreme link on another RB next to the 1 that is up there?

Estiaan

Hi Ive got an Tower on a mountain, where Ive got 2 links One is 60Km Using NV2 The other link is 28Km Using Nstreme As soon as The second link is Nstreme - My RX Quality of the 60Km Link drops from 99 to 49 Instantly, and throuhput Halves. When I Disable the Nstreme on the second link, the throughpu...

Estiaan

Hi I have setup an 60km Wireless link with full line of sight using 34dbi dishes and RB52hn Mikrotik Radio Cards. Ive got an RX CCQ of 80% and TX of 70% As soon as I push Data more than 2mb through the link it drops completely. TX RX signal of -77 but jumps around between -75 - -80 Im using Mimo Dis...

Estiaan

I want to be able to assign an DNS name to my pppoe clients, that gets an dynamic address each time they dial in?

How do I do that?

Estiaan

I know, But since I set It up with that Remote Failover, When a Connection gets opened on 1 of my adsl lines, it forces it to a different line, and therefore take alot longer to open a site

Estiaan

I tried that, with no luck, as Internet is extremely slow after I set it up

Estiaan

I am using PCC with 3 ADSL modems that is dialing the internet, so whenever 1 goes down, the internet goes Haywire, until I disable that Ethernet port. So How do i implement that scipt to check over 3 Gateways?

Estiaan

Sade thanks for replying, Can you maybe give me the simple script te enable and disable the route?
I am useless in scripts
thanks

Estiaan

Is there any plans from mikrotik to add remote ping in ip routes.

For failover using adsl modems.

As some ISP doesnt allow us to use our mikrotik boards to dial pppoe to them, they preconfigure the modems and send them to us.

Estiaan

Hi I have a problem where some of my clients requires an public IP on my network, and whenever 1 of my clients power drops, the pppoe session stays open, regardless of Timeout or not, when the clients then dials in again it get assigned the same ip address as the session that is open allready. Now I...

Estiaan

anyone?

Estiaan

Hi I have a Problem, where some of my clients gets a static PPPOE dial in address from my Radius Manager, now as soon as the clients CPE reboots or loses power and dials in again, it Creates a second active session, and then The static Address Timesout when you ping it, Thus causing my client not to...

Estiaan

I have a problem with my PCC Setup, all 3 my WAN Connections are 4mbps down and 512k up, but when I try to download anything I wont get more that 200k, where normally I could get 400k. and then all 3 my lines would idle? Any idea why? Here is my Mangle rules /ip firewall mangle add action=mark-routi...

Estiaan

No, I see that sometimes it streams fast, and othertimes slow as hell

Estiaan

I changed everything back to PCC and the youtube streaming is still slow, Ive got 3 4Mb lines running at 1Mb each constant, So Ive gor alot of free bandwith per line

What can be the problem?

Estiaan

I have an PCC Load Balancer with 3 x WAN Connections, All 3 Lines running at 4MB

Will my PCC load Balancer check which ADSL line is open and force the traffic through that line? or will it just push all traffic to a line that is allready running at full capacity?

Estiaan

Here is my Mangle Export, Please help mme with my PCC. IS, Mweb and Mweb2 are my 2 DSL lines connected on the load balancer /ip firewall mangle add action=mark-connection chain=prerouting disabled=yes dst-port=22 \ new-connection-mark=Mweb_conn passthrough=yes protocol=tcp add action=mark-routing ch...

Estiaan

In SOuth Africa ABSA online bank could not log in at all with PCC, as soon as I set it On ECMP and Marked all Port 443 traffic to 1 Wan connection, it works perfect,but youtube is super slow. Everything else is fast

Estiaan

with PCC all my port 443 traffic gets splitted and then gets logged out, which causes a problem

Estiaan

Ive have a funny problem, I am using ECMP Load Balancing on 2Wan Port. Internet is super fast, But when I watch any Youtube Clip, It is very slow.

What can it be?

Estiaan

please help anybody

Estiaan

The public Ip is set on the modem interface. Which is behind the PCC Load Balancer. Must I then port forward through to the load balancer and then the ap and then the client?

Estiaan

Hi I have got an WISP, 1 of my clients needs an public IP (x.x.x.x) I have got an Mikrotik PCC load balancer (192.168.3.240) which has got the adsl line connected to with the Public IP (x.x.x.x) My AP ipaddress it (192.168.3.78) Client connected on the ap is (10.5.60.x) How can I assign my Public IP...

Estiaan

I am struggling to split voip traffic and internet traffic.

I have 2 gateways, but cant seem to split the traffic. I am using mangle to mark routing, and then in ip routes set the gateway for routing traffic. please help

Estiaan

Both gateways is on 1 interface

Estiaan

thanks for replying

How do I implement that using gateway 192.168.3.240 - 192.168.3.254

as they are on the same range?

Estiaan

I have got 2 adsl lines that i want to load balance

192.168.3.240
192.168.3.254

is this a correct way? or do you need to mangle the packets?

Estiaan

I have setup an hotspot for an local school hostle, and for some reason Facebooks homepage loads, but as soon as you try log in, it just keeps loading and nothinbg further, why can that be?

Please help!

Estiaan

Can one run an Mikrotik R52hn card as an access point using both chains on a dual pol Sector?

Estiaan

When I click on a user and look at statistics, it does the same thing.

This jumping around cause my clients to get more bandwith for free

I dont know how to stop this

Estiaan

I have configured the transfer limit on the profile and assigned a profile to the clients that has a transfer limit of 3GiB

What can be the problem with the usage that jumps around

Estiaan

I have got another question, If lets say I set my transfer limit for my clients to 3GiB, and the client uses 2.5GiB Download and 500m upload, will my client get capped?

Estiaan

Yes it is RouterOS 5.6

All of these are taken 30seconds after each other.
I have set my interim update every 1min, and 1 session per host

Look at Willem, Sean Usage, and it even goes down to 2Gib each sometimes
User manager router does not restart or lose power at all

Estiaan

all my clients that authenticate using user manager realtime usage jumps around
It will be 2.1Gb now and 5min later 2.7Gb and a few minutes later 2.0Gb again

What can be the problem

Estiaan

Please help me with routing problem My whole network runs on 192.168.3.0/24 network and my gateway was 192.168.3.254 now recently I got an new ADSL router with an static address 196.214.186.x I cannot get my routing solved, my RB that is connected to the gateway 192.168.3.254 is 192.168.3.90 Where m...

Estiaan

I have a small problem, I setup n Network between 2 points, when ever I ping anything on the internetI have packet loss, but when I ping my second point there is no packet loss at all, I am presuming it is WDS, any advice maybe?

Estiaan

Hi
I have setup an link 6km with R52hn cards bothsides on Nstreme dual slave, my signal strength is -61 both sides, my transfer rates is 65mbps max and under load it drops to 30mbps, can that be an allignment issue? I was hoping on getting a link over 100mbps, What am I doing wrong?

Please help

Estiaan

Hi all, i have got an question, i have set up an link using rb800 and r52hn cards the link is about 6km, and has LoS, i am using 2 27dbi grids on both sides and arenusing both chains on the cards. My signal is about -53 and quality of 70/80%. bandwith test only shows about 45mbs, is that the best i ...

Estiaan

I have ordered myself a few SXT but I have noticed that they are really weak, I cannot even connect to a link that is more than 5km, I am running Dbii F50 Pro Radios on the 16dbu sectors, and these SXT on 2km Have an signal quality of -85, Is that normal?

Estiaan

Hi I have an 6km link on two RB800 running R52hn both sides with an 27dbi 5Ghz grid bith sides, I get an Link of -74 and 60%CCQ? When I do an bandwith test I get bout 37 - 40Mbps, is that the best it can do? I am running it in Nstreme? Any advise on how to increase that speed? Im running in N-Only m...

Estiaan

I have set up a Wireless network N-Only between to RB800 and my TCQ is 95% with data rates of 70Mbps, When I try Ping anything on the Internal network (Between the wireless link) Ther is absoultely no Packet loss, but when im on the Routerboard which is wireless connected to the rest of the network ...

Estiaan

Hi i am fairly new to the dude, i setup an wisp and now i want my dude to send an sms to me, i have read up on email2sms and tried vodacoms service but does not look like it is working, i saw an post where they used "blat" to send out the email, but that aint working aswell, can somebody r...

Estiaan

Hi can an yone please help me ive got a slight problem, I have got an adsl router that is on dhcp, the only way that I can get internet on my Routerboard 800 is Setting up the DHCP client, which is a pain, so now I want to make the board a Static IP adress on eth1 which is connected to the router to...

Search found 94 matches