System is unstable for first 10 minutes or so. CPU is 100% and attempts to logon result in crash. After the time, CPU goes back up normal. This was also true on 7.1.3.
Did an upgrade from 6.49.2 to 7.1.3 on my RB751U-2HnD. Basically dead. Reset it to factory default and was able to get the router working. It was a simple config so I just did the whole thing. Didn't trust the restore of the backup to work.
WHOIS says the the registrar has put the domain on hold. ICANN says "Often, this status indicates an issue with your domain that needs resolution. If so, you should contact your registrar to resolve the issue. If your domain does not have any issues, but you need it to resolve, you must first c...
People have to realize that Passive POE has no voltage standard. Both 24v and 48v are in popular usage. One simple check of the specs would have seen that your PBX is 48V and the Mikrotik units you tried are 24V. I have successfully powered up 803.af devices with 48V passive POE using my Netonix swi...
We have a bank of five CRS125-24G-1S. We also have a Cisco WS-C3560-24PS switch One CRS was upgraded to V6.43.7. That unit will not connect to the Cisco. The symptom is that both units (Cisco and Mikrotik) have flashing link lights. The Cisco is logging ethernet up, ethernet down a few seconds apart...
We just installed a similar setup although our run is shorter.. 24V is not the "golden rule:. We used a 30V supply for the POE We thought about 48V. The PowerboxPro is rated to 57V but our radios (non Mikrotik) couldn't take that much.
Answered my own questions 1. You don't seem to see the power supply status using Winbox 2. Command line works /system health print fan-mode: auto use-fan: main active-fan: main cpu-overtemp-check: yes cpu-overtemp-threshold: 100C cpu-overtemp-startup-delay: 1m voltage: 24V current: 758mA temperature...
How does one check the status of the dual power supply on Routerboards such as the CCR1009-8G-1S-1S+? I don't see anything under the "System" "Health"/ Is something available via SNMP?
Log window enhancements gone in B3. If I start Winbox3B2 and connect to a router, the log window allows resizing the columns. If I start Winbox3B3 and connect to the same route, the log window does not allow resizing columns. The B2 log window has filtering and the B3 log window has a freeze button ...
I don't know what your exact configuration is so I am making some guesses. I am also definitely not an IPSec guru. I think your problem stems from the IPSec configuration. The source and destination addresses have to specified in the policies The packet from 10.102.6.0/24 is destined for 10.10.4.0/2...
I was upgrading a fresh out of the system RB951 and tried Winbox 3 I was unable to drag and drop a file onto my router. I got the little black circle with slash symbol indicating "NO". I can drag and drop from the router to my system. System is Windows 7. Switched back to the old Winbox an...
I did reset the DPI to 100% and that worked except the font is too small for my old eyes. Rather than trying to find some magic settings of screen size and DPI that work, I will just wait for the fix.
When I use winbox to view the log screen on my Windows 7 laptop, the time field is truncated. It will show something like 07:4... This started with version 6. Routers with V5 ROS show the log screen correctly. Winbox doesn't allow the column sizes to be changed on the log screen Is there a way to fi...
I have two buildings separated by about 250m and plan to run fiber between them. Mikrotik routers will be in each building and was planning on using gigabit S-85DLC05D modules. What fiber should I use? My reading says that 50/125micron OM3 category fiber but the contractor says 62.5/125 would be OK.
I been looking into upgrading a site after the lone Mikrotik router "failed" this morning and needed a power reset. I have come up with a two router solution using VRRP My question is how independent of the software is the hardware switch portion of the router? If I have two ports connecte...
The other way to do this is to have an "pseudo" IP address like 192.168.2.1 on both Web servers as an alias. They you route 192.168.2.1 via 192.168.1.5 with distance 1 and via 192.168.1.6 with distance 2. If 192.168.1.5 stops answering the ping, the route will go inactive and switch to the...
Anyone know how to get the time column on the 6.1 log page to display all the digits. It shows something like "Aug/01/2014 17:08..". It works OK on my XP system but not on my Win7 system
It would be nice if Winbox warned you if you are in Safe Mode and you try to close the window. A simple: "You are in Safe Mode. Do you really want to quit" would be great
As someone mentioned, this is an L2 problem. It is two STP bridges that need connecting. Unfortunately, this is a small box (RB750UP) and all the hardware ports are taken. With the failure of EOIP within the same box, I guess that leaves a metarouter.
For various reasons (technical and business) I have a Mikrotik router with two instances of "bridge". Each instance is running STP and I want to connect the two instances together. There doesn't seem to be an easy way to do this. The only one I can figure out without resorting to a MetaRou...
Installed 6.0 on RB-750. When to System -> Reset Configuration and reset with "No Default Configuration" not checked. Box came up with no configuration present. Loaded in a configuration backup from a V5 system and did "Restore". Box died. No link lights whatsoever. Did a reset u...
Check the first line of mtrancid and mtlogin. They need to point to perl and expect on your system. The values that come with the scripts are probably nor right for your system.