I am having problem to use CRS317 with LACP.

I have a vyos server running LACP and CRS317 between servers. I tried to use LAG on swos but did not run. I put it passive to use LACP between server and CRS did not allow to pass it.

Please does someone knows how can I allow the LACP pass?

Thanks
Alex

I am having problem with CRS317 LAG too. It is not working. I have a bonding interface in a Vyos and between the I have a CRS317 and it is not allow to pass LACP. I tried to configure it directly on SWOS but it does not work too.

Really said!

I bought CRS317 and happen the same problem. I can access via SWos but ROS not. It is giving the same error. I tried to netinstall but it is not working. Did you manage to reinstall ROS?
Thx

Thanks everyone! The problem was BGP with OSPF in the same box. Too many updates of BGP. I solved it!
Thanks for help.

Thanks again for your help. I am no advertising the pppoe network in OSPF to reduce the interfaces in it. I am running in this RouterOS BGP peers in the server. Do you think is is the problem to recalculation drop the OSPF? I am setup a new RouterOS for BGP, firewall and OSPF to connect to authentic...

Thanks again for your help! No filter in OSPF. Should I use filter for PPPOE clients not propagate? Do I need to filter any more things?
Thanks

Now I found out the problem. It is like a loop after a router come off. The ospf goes crazy and cpu really high. Then all the routes falls and comes up after this. I have a summarized area for pppoe clients. I am using ptp as network type on ospf. I have 6 router in one ether out for a switch. The a...

Thanks again! It happens with things that change on route table. It is really strange because crash all routes and increase cpu. Other changes is okay!

Today I have disabled all the Discovery Interface at Neighbor List. After it crashed again! It is something about route table for sure.

It only happens at CCR. The other routers are with the same number of routers neighbors does not have it. But the difference is that each route is linked at one interface. The CCR use one ether for all the internal network.

Thanks for reply! I started after increase routers and add a BGP session. I was with RouterOS 6.30 but I upgraded to 6.30.4 to try to solve. I tried after read the changelog. What's new in 6.30.4 (Aug.25.15-12:59:46) *) route - fixed crash on removing route that was aggregated; It did not help me to...

I am running RouterOS 6.30.4 with OSPF and MPLS. If I change something in a router of the network all routes crash in main server. The main server is a CCR 1036. The cpu goes up and it crashes all the routes. After a minute the cpu goes down and the OSPF starts again. pppoe, routes, vpls and ospf go...

I would like to know if can i use at NetMetal 5GHz Triple Chain only two chains? Stop one if i do not want.

Hi !!! I have a server in RouterOS 5.24 and the clients connects by pppoe. The MTU and MRU is 1492 and to surf is ok. The pppoe clients still connect for ages but skype and others programs are disconnecting sometimes. There is no cycle to disconnect but sometimes 1 minute or more. What can it do? I ...

If I first put forward rule to accepting all the ports, then some rules for input ports to router and finally drop all via input.

Means to my clients all the ports are released by forward or only those accepted in the input?

It works like this? Or gotta release input for the forward work?


Thanks

Duplicate ping responses can be caused by: More than one host has the same IP address, so all these hosts will respond to the ICMP echo request. The IP address pinged may be a broadcast address. The host has multiple TCP stacks bound to an Ethernet adapter. A router believes it has two routes by wh...

He has the same problem. http://forum.mikrotik.com/viewtopic.php?f=13&t=69772

I still have this problem in many device with 5.24.

Please! How can I solve it?

Thanks normis!

I sent it.

One of my Omnitiks stopped to work. It was in ap-bridge mode and ether1 link and poe. It was working fine for 6 days, but It stopped. I replaced it and I am having problem to understand why. After reset it over ether 4 because it did is not allowing me to access ether1. I do not have firewall rules ...

Thanks for your reply! I do not have security profile. Only MAC control.

I am having issue in my network. Some clients with CPE dialing to pppoe server is connecting the AP in bridge with good signal and is not sending package. But the are receiving! It is happen different APs too. What can it be? After reboot sometimes comes back. The are others clients in the same AP a...

It is a bug for RB433uah! I did a downgrade to 5.11 and now it is ok again.

I need the mipsbe 5.11 npk for downgrade to last version. Where can I download it?

this pings are reaching ether1 not wireless pings.

From one of my linux servers in the network. It is the same to the device. The strange thing is only to device but it does not happen to it client by wifi. root@gladiador:~$ ping 10.0.0.30 PING 10.0.0.30 (10.0.0.30) 56(84) bytes of data. 64 bytes from 10.0.0.30: icmp_req=1 ttl=30 time=29.2 ms 64 byt...

Hi is ping normal! After a few pings it start to re-ping the same replay. See here!

I did a test to ping from other device to upgraded device. It is the same!

Why? Was ok before! There is two R52HN on it in ap-bridge.
Thx

It was a restriction at destination server for my range of ips. I informed the host company about that. Soon it is going to be fixed.

Direct from the internet link. From the fiber router but it was tested with other range of ips. That is why worked.

Thanks for you attention!

I really do not know. It is weird for me because it was working.
Only one site not accessible. Crazy staff!

Please guys help me!

Hi! I have a RB1100 and It was working properly now is blocking a site. Direct from link is working but behind mikrotik is not any more. Nothing was change! The DNS is working and the site too. dig www.solimar.com.br ; <<>> DiG 9.7.0-P1 <<>> www.solimar.com.br ;; global options: +cmd ;; Got answer: ...