MikroTik

esorin0

Hello! According to Chateau LTE6-US product page https://mikrotik.com/product/chateau_lte6_us , the product is "US carrier-certified". I have attempted to activate a Verizon SIM card using Chateau LTE6-US IMEIs (I have 3 of them) and none of them were actually worked, message being that pr...

esorin0

Hello!
I see that CCR2004-16G-2S+ power supplies can be replaced. Any idea if there is a -48VDC option, available or planned?
Thank you!

esorin0

Same voltage that is applied on the DC input. In my case, 54V of 24V, depending on input. Again, I understand the product is not usable in a -48VDC environment and that's my fault assuming it will work. I should note here that the similar product from Ubiquiti states very clear in their documentatio...

esorin0

Yeah, that's my bad here, device cannot be used in a -48VDC because it is not designed to be. It works fine without the ground, but that's not the right way to do it. Mixing positive and negative ground is a bad idea, as I discovered the hard way. @Lifz, thank you for your quick and full of kindness...

esorin0

Hello, We have ordered 2x netPower 16P and they both put out current on the frame ground screw. It's the same voltage that's going in via the DC ports. I am assuming that we did not receive 2 defective units and that this is the design. That being said, it's a bad design, since it pops our fuses all...

esorin0

Is "high" standing for 802.3af and "low" for passive POE? And it really depends on your "flexibility" needs. As far as my needs, I always have to invent something to power these devices, in order to make them work as they should be (redundant as far as power, telco envi...

esorin0

@Elans when is Mikrotik planning to release any of these devices with a dual PSU (AC or neg48V telco)?

esorin0

That document is as confusing as all the other places. I did not find any clear mention about the type of POE that can be used when only the low voltage input port is connected. Is this device able to supply 802.3af when it is powered via the 18-30V port only?

esorin0

I really don't understand why Mikrotik is not making (more) dual neg48 devices. For devices like 16P or bigger switches, those have very high chances of getting installed in such an environment. Is tehre anyone that installed 16p in a dual neg48 power setup?

esorin0

Is device able to provide 802.3af only with the 18-30V PSU port connected? I am not able to find a clear reference to that, as documentation looks to be left intentionally confusing.
"Or you can set manually per port" - how does that work with only the low voltage PSU connected? Thank you!

esorin0

Are we able to use IP pass through with UML295 or is it working only in a double NAT scenario?

esorin0

Rebooting and disabling watchdog temporarily fixes the issue. One day later, all the windows are empty and the log shows scrolling messages saying "timeout while waiting for program X", where X=16,20,44,96. The issue is happening on the same routers that had issues with kernel failure. Scr...

esorin0

Hello, During last 2 weeks I've upgraded several RB2011 to ROS 6.38.5 and latest firmware (3.33). All of them are dialing an openvpn connection to a central server for management purposes. Also, all have a watchdog rule to reboot if they cannot ping the VPN management IP. Yesterday, that management ...

esorin0

Hello, Is there a way to get a socat like behavior on ROS? I have several devices behind Mikrotiks that have a different default route and without possibility to add routes on them. The only way I can connect to them from Mikrotik side is via an IP in the same IP range. Having a Linux there is not a...

esorin0

What do you use for external power supply? The 2011s are powered from 2 different sources and I would like that for USB modem also.

esorin0

+1 UPD & LZO
+++++

esorin0

Hello, I have several Verizon Pantech UML290 USB modems, each connected to a RB2011UiAS. They work fine most of the time, but they are disconnecting from time to time. Logs are getting full with messages like: async,ppp,info vz: initializing... async,ppp,info vz: reseting link... async,ppp,info vz: ...

esorin0

I have done this on RB2011, but will it work on RB450G ? According to the guide here: http://i.mt.lv/routerboard/files/rb450G-qg_1377089382.pdf Powering The device accepts powering from either of the two power jacks, or from the LAN1 Ethernet port: • direct-‐input power jacks J801/J803(5.5mm outsid...

esorin0

Hello,

Does RBPOE-CON-HP work with input from telecom negative 48V?

esorin0

Sorry to revive this ancient thread, but I am interested in a working solution to power Mikrotik routers (RB450G or RB2011) from telecom -48V. Thanks!

esorin0

Thanks!

esorin0

Anyone?

esorin0

I just hope they support OpenVPN UDP. I just don't get it why MTK refusest to implement this feature. Their passive-agressive answers on this forum are at least weird. They are inviting you to look someplace else. Too bad, it is a great product, flawed by some really bad choices. Too much "russ...

esorin0

EdgeMax is not yet available for buying. And no idea how it will perform, as it is in the "baby" stage. I will buy at least 3 as soon as they are available

esorin0

Any updates in this area? Or is there any VPN tunnel fully supported in ROS, that works over UDP? Well, except L2TP...

esorin0

I've found a link from a guy that experienced a similar problem: http://rant.gulbrandsen.priv.no/mikroti ... olicy-bugs

esorin0

It's most likely the switch. Any idea if that is a feature that I should look on switches? Or do you know any 5p switch that works in this setup? I would rather change the switch than put even more scripts for workarounds.

Thanks!

esorin0

Hello! I am trying to setup 3 RB750s like that: - one site A - as L2TP/IPSec server - the other site B1 and B2 as clients to A. The network behind B1 and B2 is the same. The problem I have is that when I setup the IPSec policies with same subnets but different endpoints, it disables one of the rules...

esorin0

Hello!

Actually this was not a routing problem, but an IPSec problem, due to the fact that I have 2 different policies for the same networks, but with different endpoints. Once I disable one of the conflicting policies, it works fine. I will open another thread for that problem. Thanks!

esorin0

Any luck on this? I have more or less the same problem: it works fine falling to the backup, but once main is back, I have to wait over 2-3 minutes until the network computer see the virtual gateway.
Due to my setup I need to switch back to the main router, once this is back online.

esorin0

NAT is disabled on both routers. I do not see any kind of packet at the ends, with tcpdump.

Although I do not want NAT, I want to try that too. How do I enable NAT passthrough?

Thanks!

esorin0

Hello! I have this setup: PC A - RB750 A <- L2TP/IPSEC -> RB750 B - PC B I've made the setup according to this link http://wiki.mikrotik.com/wiki/L2TP_%2B_IPSEC_between_2_Mikrotik_routers The problem is that I am not able to reach PC B from PC A or PC A from PC B. I am able to reach PC B from RB750 ...

esorin0

Hello,

I am looking for N2N in ROS too. I really don't like openwrt approach!

esorin0

OpenVPN proto UDP works very well on high speed sat links (10mbps down/4mbps up), without PEP. Unfortunately, MTK implementation of OpenVPN does not support udp (and comp-lzo), so it makes it pretty useless. I wonder why is even implemented, since the main features of OpenVPN are not working. I've r...

esorin0

I've found a PEP for Linux - PEPsal, which seems to be implemented in openwrt. However, it is an older version and I am not really interested in an openwrt platform.

esorin0

Hello,

Did anyone implemented PEP (Performance Enhancing Proxies) with Mikrotik hardware, for enhancing VPN performance over high speed satellite links?

Thanks,

Sorin

Search found 36 matches

Chateau LTE6-US and US carriers

DC PSU for CCR2004-16G-2S+

Re: netPower 16P power design flaw

Re: netPower 16P power design flaw

netPower 16P power design flaw

Re: netPower 16P max total power

Re: netPower 16P High Low?

Re: netPower 16P max total power

Re: netPower 16P max total power

Re: netPower 16P High Low?

Re: Verizon UML 295 support

Re: RB2011 watchdog stuck after upgrade

RB2011 watchdog stuck after upgrade

Socat like proxy

Re: Pantech UML290 reset

Re: Feature request: OpenVPN compression LZO and UDP

Pantech UML290 reset

Re: multiple power input

RBPOE-CON-HP and neg. 48V

Re: RB 600 with Telecom power (-48v)

Re: IPSec not working multiple policies -same subnets

Re: IPSec not working multiple policies -same subnets

Re: Feature Request: OpenVPN [ovpn] udp tunnels

Re: Feature Request: OpenVPN [ovpn] udp tunnels

Re: Feature Request: OpenVPN [ovpn] udp tunnels

Re: IPSec not working multiple policies -same subnets

Re: Force ARP packet on VRRP Master state change

IPSec not working multiple policies -same subnets

Re: L2TP routing debug

Re: Force ARP packet on VRRP Master state change

Re: L2TP routing debug

L2TP routing debug

Re: Several features request

Re: Performance Enhancing Proxies

Re: Performance Enhancing Proxies

Performance Enhancing Proxies