I would also like to know what these indicate? My HAP AC lights are changing colors at regular intervals. The WiFi led, for instance, holds orange for 3 seconds and then momentarily changes to red and then back to orange again. The 5th port with POE out changes is similar but will blink red between...
Only RB941 but this is slower It is, actually, faster. CPU 650MHz (hAP lite) vs 400MHz (RB951-2n) More Mhz is not more powerfull. See the Honzam's comparation. http://forum.mikrotik.com/download/file.php?id=19763 The hAP lite is much faster than the 951-2n in my experience. Mikrotik tests the throu...
Is there an equivalent to RSTP on the RB2011 or CRS125 that utilized the switch chip instead of the CPU? I am hoping to increase the throughput and skip the CPU entirely. Currently I have a RB2011 with two Uplinks but the throughput will not go beyond 175mbps. No firewall rules or mangle rules setup...
I do not have any insight into this issue but I have a similar observation from ubiquiti wireless devices vs mikrotik wireless. Attached is a smoking graph where the switch from a Nanostation M5 to a Sextant5 is apparent.
I seem to be experiencing the same issue with my CCR3036. I can not attribute this to a load issue though. It seems that at any time of the day, SSL sites have a large delay initiating TCP transmission. Many banking sites are extremely slow and some practically unusable. Any insights into this from ...
Im terrible at Regular Expressions but there is probably a way to combine these REGEX into one L7 rule. Having a ton of Mangle/L7 Rules will give you a fairly large performance hit.
Wireless, Wired or Both? It's both. At the head end, I have a tough switch powering various access points, though. Can't do port isolation without implementing VLANs first on those devices.. So while clients can't speak with their next door neighbors (attached to the same rb2011 or cloud router swi...
You would effectively shut down your network....IPv4 requires Layer2 multicast and broadcast for ARP to work along with a number of other protocols. Limiting the rate of broadcast/multicast traffic would be a better solution...you accomplish this by turning on the firewall for bridge traffic in bri...
I played with the packet size and got up to 40 meg throughput. Better, but not what I was looking for. I did the pcq type queue and I saw full throughput. My question, Can I create separate pcq queues per ip address similar to what I was doing with simple queues? I read up on the pcq queues and it ...
Plisken; are you the owner of wirelessinfo.be? Are you JP? When yes: we mailed some time ago according wifi channels. When no: never mind :-) For firmware see this http://www.wirelessinfo.be/index.php/mikrotik/pages/rbupgrade While it doens't seem to be hard to upgrade the firmware, something goes ...
Ive looked at the profile while running speedtests, torrents, downloading files from known servers etc. Its always 80-90% idle and still limits to 30 meg. As soon as I lift the simple queue I get back to 100 meg from the same sources. add queue max-limit=100M/100M Name=Test Target=10.40.1.253 I get...
I think you are looking for this: http://wiki.mikrotik.com/wiki/DSCP_based_QoS_with_HTB As I understand it the DSCP prioritization would only really happen if you are hitting a bandwidth limit (either imposed by your connection speed or self imposed by queueing). Also, the QOS you are trying to acco...
If you are using simple queues for clients try changing the default queue size to something between 75-150 packets. The default queue type for simple queues is set to pfifo "default-small" which has a Queue Size of 10 packet. You can't push more than 12-20mbit to each customer at that buff...
enable Chain 0 and 1 at both ends. BTW, Your CCQ is really bad. :D This is Your problem. Thanks for the reply samsung172 but this image is just an example of what I saw. Its not actually the stats from this particular link. I check both sides and Chain 1 is enabled. Do you have any other ideas of w...
enable Chain 0 and 1 at both ends. BTW, Your CCQ is really bad. :D This is Your problem. Thanks for the reply samsung172 but this image is just an example of what I saw. Its not actually the stats from this particular link. I check both sides and Chain 1 is enabled. Do you have any other ideas of w...
I just setup a new PTMP link with a SXT-5-SaR and an SXT5-lite. The SXT5-lite as a CPE has terrible connections speeds. It connects at 60mbps/30mbps in an NV2 setup. 40mhz channel width as well. I just noticed CH1 does not show a Rx signal strength. Is this indicative of a polarization issue with re...
Does the bridge have 4 independent ports or are they part of a switch group? What hardware are you using? Not sure if this is how it works or if I'm just not doing things incorrectly but I have RSTP enabled on a bridge with 4 ports. I loop two of the ports together with another switch just to test a...
I just noticed this troubling behavior on a 750UP that I thought was working fine. Heres what I noticed... When in viewing anything related to POE out monitoring in WinBox or terminal(Bridge window or the Interfaces window in Winbox) the ports would flap and the logs reflected that. If I reboot the ...
Thanks for the notes. Ill double check disabling all ports other than the uplink and my connected port. I do not believe its a separate DHCP server as I have rogue DHCP detection set on my core but I will investigate...
I have a network that is bridged to clients. Mikrotik all the way through. CCR <-> Sextant5 <-> Toughswitch(at the POP) <-> Sextant5 <-> Sextant5 <-> RB2011rm(all bridged ports) <-> RB951-2n(CPE's) Bandwidth Test from the RB2011 to the CCR gets at lest 100mbps throughput in either direction. If I ru...
I am using RSTP between two sites as failover... 450G router, Port2 and Port3 are in Bridge1 and currently RSTP is blocking Port2. Failover works just fine but my question is does 450G perform RSTP on switch ports in the same fashion as it works on Bridge ports? If I removed the Bridge1 and slaved P...
I funnel all of my free hotspot traffic to an external Squid server using a simple Nat rule for port 80 traffic. What I would like to do is show a splash page to new users as well as users who have been idle for more than an hour. This splash page is probably too heavy for the built in web server. I...
I have a working hotspot setup with some banner advertisements in the login page that I change out pretty often. I have been trying to figure out how I can remotely view the mikrotik's web server. So, for instance, when I make a change to login.html remotely, how can i view what the Mikrotik is serv...