MikroTik

fcucci

Hello, I have installed routeros 7.1.1 on a CCR1009-7G-1C-1S+ (tile) but I don't see packages listed; on terminal too: Immagine 2021-12-27 122604.jpg In ROSv7 only a few non-essential things come as packages, everything else is in a single monolithic intallation package. OK and how can I uninstall ...

fcucci

Hello,
I have installed routeros 7.1.1 on a CCR1009-7G-1C-1S+ (tile) but I don't see packages listed; on terminal too:

Immagine 2021-12-27 122604.jpg

fcucci

Hello,
we have 2 BGP Peers and we are adding another one that cannot send us a default route via BGP; is there a way to enable a static default route only when BGP session is UP ? In other words can we have a default route only when that peer is UP like if him send it us ?

Thank you in advance.

fcucci

Hello, with a /siystem/reboot it has begin to work good.

Thank you for your help.

fcucci

hello,
no it doesn't work; it take about 40/50sec to tell me:

add name=lo6-1
action timed out - try again, if error continues contact MikroTik support and send a supout file (13)

Maybe I have to reboot it but I hope it will restart.

fcucci

Hello, we have a border CCR1072 router with OSPF and BGP, IPv4 and IPv6, enabled and working; for error we have disabled lo6 (loopback bridge fro IPv6) and now we are not able to enable it again. Router seems to be stuck and if try to enable loopback bridge we have the following error: in bridge pr ...

fcucci

Hello All, we have 3 routers, BRAS1, BRAS2 and Core Router; two BRAS and Core are connected in a OSPF NSSA area; /32 routes connected at BRASes are advertised to CORE without problems. When a client with a static route connect to one of BRAS with "framed-routes" radius attribute, the stati...

fcucci

Hi doneware,

OK, now it works good.

Thank you so much !!

fcucci

Nobody ?

fcucci

Hi All, I have a problem with a script; it works good via shell but doesn't work on system/script also if I import the code exactly as is. {:if ([/routing bgp peer get [find name="CYMRU-1"] state] = "established") do={:global CYMRUSTATE;:delay 1;:set $CYMRUSTATE value="1&quo...

fcucci

Upgrade from 6.38.5 to 6.42.1, I had a bridge with 3 vlan inside and after reboot only one vlan is present in the bridge; we have added the remaining 2 vlan manually. Can you check that and why it appens ?

fcucci

Hello all,

in the 6.35.4 version the issue isn't solved. The dude is not able to connect to ROS devices in secure mode. Someone can tell me if have solved the issue in another way ?

Thank you.

fcucci

We have issue with the DB import from old dude v.4 on windows server to the dude v.6.35rc7 on x86; after the DB export and import ended without errors, we have all ROS devices cannot connect to dude and we see status "failed" as the attached image. From the device settings if we uncheck th...

fcucci

Dear System Admins, today I wrote a script to take some wireless information from a ROS device and bring them in PRTG network monitor; now in the ROS system log I view hundred lines like these: date/time system.info,account user ***** logged in from ***.***.***.*** via ssh date/time system.info,acco...

fcucci

The device is Groove A52HPn
The band is 5Ghz A/N
Country : Italy
The wireless interface is obviously activated

Now I write at support with screenshot and supout file.

Thank you.

fcucci

Hello All, I noticied that on some Groove 52HPn, after the upgrade to ROS 6.4, the TX power is at maximum power of 27dbm. If I set : 1.Frequency mode to Regulatory domain, TX Power mode to default and antenna gain to 13, the current TX power is always at 27dbm; 2.Frequency mode to Manual TX power, T...

fcucci

Yes, it is only required the registration table print command. The second global parameter doesn't need nothing, it work howerver.
Thank you, Francesco.

fcucci

Hello Skot, thank you for your reply! Your suggestion for "preferredAP" and command find vs. comment is valid! For "currentRN" if I use find command vs. mac address and that AP goes down, if I go to change it, the find command to search that mac address is not longer valid. I am ...

fcucci

@Uldis
I have tried to contact support@mikrotik.com without success; I have writed 3 mail in 15 days but I have no reply about this issue.
Thank you.
please provide with the support ticket number

Ticket#2013091366000633

fcucci

Hi All, I'm tring to write a script like this : # set variables # :global currentRN [/interface wireless registration-table get number=0 value-name=radio-name] :global preferredAP [/interface wireless connect-list get number=0 value-name=ssid] log warning message="Check AP connection vs. Connec...

fcucci

@Uldis
I have tried to contact support@mikrotik.com without success; I have writed 3 mail in 15 days but I have no reply about this issue.
Thank you.

fcucci

Before ros 5.15 now 5.25

Thank you.

fcucci

Hello Sys Admins, I want to share with you a strange issue with a PtMP AP (RB433AH), 2 radios (R52Hn), NV2 wireless protocol enabled, channel width 20Mhz, 25 client each radio connected. Until 10 days ago the clients connected to, have low latency (10/20ms) and good throughput 4/6Mb/s; likely, after...

fcucci

OK,
now work, thank you!

fcucci

Dear Colleagues, I need help on a script. I want to put an IP address without /netmask in a global variable to use later in the same script; the code is: :global address [/ip address get [find interface="lo"] address] :global addr [:for i from=( [:len $address] - 1) to=0 do={:if ( [:pick $...

fcucci

OK,
solved, thank you!

fcucci

OK,

thank you, but in this case the winbox start but ask me the address the user name and password; how can I send him the variables listed above ?

fcucci

Hi All,

why, when i use the winbox tool in the dude, I don't see the safe mode and undo button, the hide password flag ?

How can I solve the problem ?

Thank you.

fcucci

OK Normis,
I find the solution :

oid("1.3.6.1.4.1.14988.1.1.3.10.0")/10

Now it work correctly !
Thank you.

fcucci

Hello All,

why, when I use the OID ".1.3.6.1.4.1.14988.1.1.3.10.0", the temerature value is coming whith a 0 at the end?
In other words, if the temperature is 35° , on the Dude the value is 350.

Thank you for your answers.

fcucci

Hi,
I have purchased a new CCR1016; at first start up I noticed the ether4 in running state without any cable attached; if I put this interface in a bridge, the port flag change in Running and Slave.
Can someone tell me why this behaviour ?
Thank you.

fcucci

I didn't understand, explain me better,

thank you.

fcucci

Thanks to all, as I said in previous post, in our network I’m enabled LDP protocol and setup (on AP) VPLS Tunnels to travers some routers and arrive to my PPPoE concentrator; well, if I cross more than one OSPF area, the VPLS tunnel come up on both side, but with /ip neighbor discover I can view the...

fcucci

Hello Thierry,

thank you for your answer.

I am using LDP tunnels not TE . Why don't cross the OSPF areas ?

fcucci

Hi all, On my network I have enabled OSPF and MPLS to create some VPLS tunnels to traverse two or more routers and carry the PPPoE clients connection vs. my Core Router. If I use only one OSPF area, the VPLS tunnels come up and work regularly. If on each site, where are the AP, I create another OSPF...

fcucci

We have the same problem, when a solution?

fcucci

Hi All, i’m trying to reset the RB711 in the RB-Sextant, but without to open the case I don’t reach the switch reset button ; I have read the instruction manual when it says : "RouterBOOT reset button (access through the plastic door) has two functions" The question is : what is the “plast...

Search found 38 matches

Re: Mikrotik v7 BGP l2vpn-evpn

Re: v7.1.1 is released!

Re: v7.1.1 is released!

BGP Peer without default route

Re: lobridge disabled by mistake

Re: lobridge disabled by mistake

[SOLVED] lobridge disabled by mistake

OSPF Connected routes in NSSA Area doesn't propagate after PPPoE Interface flapping

Re: BGP Peer state

Re: BGP Peer state

BGP Peer state

Re: v6.42.2 [current]

Re: Dode doesn't connect to imported ROS devices: status connecting/failed

Dude doesn't connect to imported ROS devices: status connecting/failed

Prevent SSH login to be write in ROS system log

Re: Groove 52HPn , ROS 6.4, TX Power issue

Groove 52HPn , ROS 6.4, TX Power issue

Re: Blank radio name in script

Re: Blank radio name in script

Re: NV2 Latency and throughput issue after updrade

Blank radio name in script

Re: NV2 Latency and throughput issue after updrade

Re: NV2 Latency and throughput issue after updrade

NV2 Latency and throughput issue after updrade

Re: IP Address without netmask in a global variable

IP Address without netmask in a global variable

Re: is it possible to update winbox in dude ?

Re: is it possible to update winbox in dude ?

Re: is it possible to update winbox in dude ?

Re: Monitor CPU temp in DUDE RB1200

Re: Monitor CPU temp in DUDE RB1200

CCR1016 ether4 running without connection

Re: OSPF Areas and MPLS VPLS Tunnels

Re: OSPF Areas and MPLS VPLS Tunnels

Re: OSPF Areas and MPLS VPLS Tunnels

OSPF Areas and MPLS VPLS Tunnels

Re: RB750up at top of tower?

RB-Sextant Reset Switch